@@DiyTechBd i have old tv circuit board can I do from that or do you know anyone other sources which will help me to build my own video transmitter.???
Sorry dear. Old Tv circuit only received video siglan. Do not transmit any video signal. You need those types of device which have build in video signal transmitter or you need to build your own transmitter Circuit.
Indoor range of this transmitter around 30 meters and outdoor range around 100 meters. If you want to increase range. You should increase the tx and rx antenna range
i actually make 10 transmitters: 3 is for color info, that separates red, green, blue. i,ll use 10 bit rgb instead of 8 bit, so the value is 0-1023 (not 0-255); the other 3 is for luminance, it,s brightness, contrast, sharpness; other 3 is for audio bass, treble, stereo; last 1 is programming, to get some programs and broadcast them. without the tansmitter i said at last one, it transmitts blank and clean white screen without any audio because there is no information to video and audio. i connect the ten transmitters on laptop, and the image and sound on laptop, especialy for videos, it transmitts the full image when transmitters are complete number
Fantastic! Please tell me, if I remove the original cable, will I find only three wires (output) and can I use the 3v3 output of arduino nano or AMS1117 instead of the regulator shown in the video? And could you please make a similar video using arduino and nrf module if it is possible of course. Looking forward to your answer
If you get a voltage regulator inside the cable. Then actual working voltage of your camera is 3.3volt. If not, then your camera's working voltage is 12 volt. For that you need to use a 12v power supply or a boost converter with 3.7/4.2 volt lipo battery. You can use any kind of 3.3v regulator for 3.3 volt power supply.
Great work It worked Very Well and the frequency is 206.5 I want to ask you two things What is the maximum voltage for it ?? The Audio did not work for me? it is able to transmit audio with video on the same channel?
I did not tested the maximum voltage range of the transmitter circuit. I think 5v -9v is ok. In this circuit there is a build in audio channel. You just need an audio amplifier And connect into the audio terminal on transmitter circuit.
@@DiyTechBd aaah. You mean that output rf behind a device like reveiver that transmits video and audio analogically to an other tv. There are some receivers and dvds that are made with a transmiter rf. Right? But i should should insert an antenna as if i want to catch a channel, Right? Like what you had done.
but me, with this circuit, i will connect it to av cable instead of camera to broadcast a pirate cds. for y pb pr, i will make 3 of transmitter circuit and i will separate colors in every transmitter
@@DiyTechBd i dont want ti jamm the tv signal..i want to have my "video" on any screen with this device. fo example you make a video with your iphone and that video can be transmitted to any Screen. i walk pass by a mega screen like the times square screens. I record the vid go with my device near the scren and my picturen or vid will be shown
You can replace the camera with any kind of analog video signal. This video transmitter circuit will transmitte your video signal on tv directly. Only analog video(AV) signal. Digital video signal does not work.
If you connect an antenna on tv antenna port then you need to tune manually on any tv channel. And if you connect an antenna on AV port( yellow port) then just press AV button on your tv remote after power up your transmitter, it will be tune automatically on your tv
Its not a led tube. Just connect two wire on a Fluorescent tube. It's Act like an dipole antenna. For better result you should use professional antenna. Thanks
This is a fun project which has 100-200 meter transmitting Range. If you want to broadcast your video all around the world. You should have to go your nearest tv broadcast station.🙂. Thank you.
Very cool man! I saw that your camera is a spare back camera of a car. Also you can try to put 0ohm resistor and a ceramic antenna. It works better for me
Software defined radio(SDR) is a digital chip base warless comunication system which also required specific software. I thik it is much complicated to build at home.
You can use similar NPN transistor like BC547,2N2222 etc on RF module. I think you mean that one which i solderd on a pitch of pcb. looks like a transistor. By the way that was not a transistor, that was a 3.3v voltage regulator ic.For more information, please check on the video description.
Looks like the transmitter was salvaged from an old VCR. Here in the US that would transmit on either VHF channel 3 or 4 analog. It's just an AM transmitter, so you can use either NTSC or PAL. Audio, if used, is an FM sub carrier. Note that in the US you can't transmit on ANY TV channel. Not even under Part 15 rules. Video can only be transmitted by licensed broadcasters and Amateur Radio licensees. That being said... Don't expect to get any real range out a TV modulator like this. The picture will be quite snowy even when the transmitter is just a few feet away from the TV. You can do better by buying one of those 2.4 GHz camera and receiver combo with composite output. The video transmitter is FM. No snow (or very little). The range is a lot better, too. A solid 25 meters before the quality starts to fade.
Thaks for your advise. I already have 2.4ghz vtx and vrx. But this types of telemetry device are much expensive. But in this video, This transmitter much cheaper then other professional vtx. This analog vtx is for hobbies. Anyone can build there own tv/video transmitter.
Can I use any other RF module to build this transmitter. I have RF module in my old Sanyo TV laying idle in my house, can I use it ? Also, can AV output of a digital camera work fine with this circuit?
No. You can use only this types of RF module which is directly send Av signal to the TV receiver. Av output of a digital camera also work like charm. Good luck
@@DiyTechBd Thank you for your reply. Because am determined to replicate this project unfortunately I can't find an old VCD player but I found an old VCR player that has both RF input (antenna) and RF output(TV). Can this RF module work ? What other modifications can I make to make it work ?
What do you mean by connect in mobile?? I dont understand. If you have any questions, please leave them Below. I will try to answer Your questions. Thanks
Similar as Video signal's frequency. If you attache video and sound source on it. it will be transmit directly on tv with both audio and video signal like tv broadcast.
Sorry brother. Only analog camera/ analog video signal use korte parben jekono Source hote. Usb webcam digital. R webcam shora shori video signal o produce kore na. Er jonno specific decoder software use korte hoy pc te. Asha kori bujhate parsi.
No need to build any external receiver. Directly tune on TV. Just connect an antenna on AV port of a Tv. And press the AV button on tv remote. The camera signal tune automatic on your tv through Av port
Increase the input voltage 3.7/4.2 volt to constant 5volt. Then try again. And use a telescopic antenna on tv jack or avr input tarminal. Yellow one is the video input on TV. If you connect an antenna on Avr terminal on your Tv. no need to tune tv channel. Just press the av button on your tv remote, You will get the video signal automatically.
The modulators are designed to be plugged directly into the antenna input of televisions. They do not have the necessary power even to reach more than 10cm away. This circuit is useless.
The modulators are designed to be plugged directly into the antenna input of televisions. They do not have the necessary power even to reach more than 10cm away. What you did is useless.
I think you need more study about analog rf transmitter. At first Try it then talk. This is a build in audio video transmitter circuit and its really work. Thanks
@@DiyTechBd I have been an Electronics Technician for almost 30 years. I tried that many years ago. IT DOES NOT WORK. The only way that will work is to add a couple of stages amplifying the output.
Good to know you. For short range no need to amplify the rf signal. I can challenge you. It’s 100% work. You should try again according to this video. By the way I am also an Engineer ( Bachelor of science in Electrical and Electronic Engineering).
This is amazing. I wonder if you can make with simpler components, rather than using an already made board.
Ok. I will try. Thanks
বাহ! অপূর্ব! আমি এমনি একটি ট্রান্সমিটার খুঁজছিলাম।
Good luck.
Just awsome Brother,Go Ahead. Bangladesh is waiting for the next diy youtuber.
Thanks brother for your compliment.
Very good
I was searching for this video but your is the first one in the world. Nobody did it. Thanks lot for giving an idea.
Thanks for your compliment.
@@DiyTechBd do video will be available in onida dvd player. Pls explain it in next video only that was not clear.
Thanks. I will try..
@@DiyTechBd i have old tv circuit board can I do from that or do you know anyone other sources which will help me to build my own video transmitter.???
Sorry dear. Old Tv circuit only received video siglan. Do not transmit any video signal. You need those types of device which have build in video signal transmitter or you need to build your own transmitter Circuit.
On the schema at 7:20 the Vin and Vout are on the wrong side from the TP4056, it says both on out
I think you have to more research about TP4056 charging module. Thanks
Nice idea but one question how does florescent tube act as transmitter ? if its true then connection details plz.
Florescent tube does not act as a transmitter. It’s act like an bidirectional dipole antenna.
Oo ho bhut acha banaya hai super camar
Thanks Buddy.
Hello sir i have modern dvd player so i only found scart jack module and i dont know where to solder antenna and camera
What is the model number of you dvd Player?
Wow, great video!
thanks vay.
Yes Copyright Music.
What is the transmitting video distance and how to increase transmiting distance to high range say kilometers?
Indoor range of this transmitter around 30 meters and outdoor range around 100 meters. If you want to increase range. You should increase the tx and rx antenna range
@@DiyTechBd you also could add antena amplifiers
Yes
Why you use a rube lite for antenna ???
Coz i didn't had any other option🙂
i actually make 10 transmitters: 3 is for color info, that separates red, green, blue. i,ll use 10 bit rgb instead of 8 bit, so the value is 0-1023 (not 0-255); the other 3 is for luminance, it,s brightness, contrast, sharpness; other 3 is for audio bass, treble, stereo; last 1 is programming, to get some programs and broadcast them. without the tansmitter i said at last one, it transmitts blank and clean white screen without any audio because there is no information to video and audio. i connect the ten transmitters on laptop, and the image and sound on laptop, especialy for videos, it transmitts the full image when transmitters are complete number
can you help me with that??
I am trying to make tv transmitter circuit
Ok. I will make a video like "simple home made tv transmitter circuit".
Fantastic! Please tell me, if I remove the original cable, will I find only three wires (output) and can I use the 3v3 output of arduino nano or AMS1117 instead of the regulator shown in the video? And could you please make a similar video using arduino and nrf module if it is possible of course. Looking forward to your answer
If you get a voltage regulator inside the cable. Then actual working voltage of your camera is 3.3volt. If not, then your camera's working voltage is 12 volt. For that you need to use a 12v power supply or a boost converter with 3.7/4.2 volt lipo battery. You can use any kind of 3.3v regulator for 3.3 volt power supply.
Great work It worked Very Well and the frequency is 206.5
I want to ask you two things
What is the maximum voltage for it ??
The Audio did not work for me? it is able to transmit audio with video on the same channel?
I did not tested the maximum voltage range of the transmitter circuit. I think 5v -9v is ok. In this circuit there is a build in audio channel. You just need an audio amplifier And connect into the audio terminal on transmitter circuit.
Sir once more mini micro bluetoth wireless spy camera will be make you for me
Ok. I will try
Can we use the rf cir uit in the crt tv?
No. You Don't. Coz the rf circuit in the crt tv is a rf receiver circuit. You need transmitter circuit.
@@DiyTechBd aaah. You mean that output rf behind a device like reveiver that transmits video and audio analogically to an other tv. There are some receivers and dvds that are made with a transmiter rf. Right? But i should should insert an antenna as if i want to catch a channel, Right? Like what you had done.
but me, with this circuit, i will connect it to av cable instead of camera to broadcast a pirate cds. for y pb pr, i will make 3 of transmitter circuit and i will separate colors in every transmitter
Great
Can I use crt TV's audio video rf circuit please tell me
No. You need this types of analog rf circuit.
I don't have the fluorescent tube. Can I make the antenna by just extending the wire? Will it work?
Yes. You can. Also you can use any types of telescopic antenna. Good luck
can i use a winding of wire instead of antenna
I think Yes. you can.
If I can use Webcam, please tell me
No. Coz webcam produces digital signal. This transmitter circuit works with analog signal only.
how to build a transmitter to interrupt a tv signal like one on the time square?
Did you mean TV/Video signal jammer??
@@DiyTechBd i dont want ti jamm the tv signal..i want to have my "video" on any screen with this device. fo example you make a video with your iphone and that video can be transmitted to any Screen. i walk pass by a mega screen like the times square screens. I record the vid go with my device near the scren and my picturen or vid will be shown
You can replace the camera with any kind of analog video signal. This video transmitter circuit will transmitte your video signal on tv directly. Only analog video(AV) signal. Digital video signal does not work.
what channel you’ve use this transmitter on tv
If you connect an antenna on tv antenna port then you need to tune manually on any tv channel. And if you connect an antenna on AV port( yellow port) then just press AV button on your tv remote after power up your transmitter, it will be tune automatically on your tv
@@DiyTechBd ‘cause all i want is to broadcast on channel 38. how can i adjust the channel broadcast
You have to tune rf transformer on transmitter Circuit.
It is interesting but it may be illegal radio wave in Japan...
I think it is legal in every country with limit range.
How did you made the antenna
Which antenna?
Made from LED?
Its not a led tube. Just connect two wire on a Fluorescent tube. It's Act like an dipole antenna. For better result you should use professional antenna. Thanks
Ok thank :)
Can we use phone audio video instead of camera reply 🙏🙏
No. If you convert your phone's digital audio video signal into analog audio video signal. You can use
Then how durdharshan sent recorded audio video signals into analog signals please make a video 🙏🙏🙏🙏🙏🙏🙏🙏🙏
Can we get this rf module in market
Please tell
I want to sent signal to crt tv 🙏
How can I aim an antenna or dish and broadcast a video signal out and just like aim it out the sky at planets and galaxies?
This is a fun project which has 100-200 meter transmitting Range. If you want to broadcast your video all around the world. You should have to go your nearest tv broadcast station.🙂. Thank you.
Very cool man! I saw that your camera is a spare back camera of a car. Also you can try to put 0ohm resistor and a ceramic antenna. It works better for me
Thanks
Wow!! Absolutely brilliant & a work of art. I had a question bro. Can RTL-SDR receiver be made at home. Can u suggest any idea? Plz advise.
Software defined radio(SDR) is a digital chip base warless comunication system which also required specific software. I thik it is much complicated to build at home.
@@DiyTechBd ok bro. Thanks.
You welcome.
can i adjust the frequency of this transmitter to make a different channel??? i want to broadcast on channel 37!
yes. you can
How i can a long distance ? For example: Home from Work ( 35km)
I think you need to buy professional TV broadcast station.🙂
can i use higher voltage for this to make the transmission more far
Yes. The voltage limit 12 volt maximum.
how to adjust the frequency of this transmitter
For adjust the frequency. You have to tune the rf transformer.
As i know car rear camera work only 12v not 4.2v li-ion battrey 🤔
There is a hidden voltage regulator on power cable in every rear and front view camera. Real working voltage is 3.3v
@@DiyTechBd can we use phone audio video instead of camera
If you convert your phone's digital audio video signal into analog audio video signal. You can use
Many it's the led needs 12 volts
Very Nice ...
Good Try...
👌👌👌
Thanks
All the dvd player board are same ?
I think similar.
Hey I have a project transmitting a video into outer space. Do you know how I would do that?
What do you mean by outer space? Please explain it first. Then i will try to answer you.
Was this project done in India?
No
In Bangladesh
Yes brother.
Bro can we use another type of transistor here
Yes. You can
Pls name them and thanks
You can use similar NPN transistor like BC547,2N2222 etc on RF module. I think you mean that one which i solderd on a pitch of pcb. looks like a transistor. By the way that was not a transistor, that was a 3.3v voltage regulator ic.For more information, please check on the video description.
which is the frequency that the television transmitter uses and also if it transmits in Pal or ntsc?
This Transmitter uses Reguler tv tuning frequency in both Pal and Ntsc.
Looks like the transmitter was salvaged from an old VCR. Here in the US that would transmit on either VHF channel 3 or 4 analog. It's just an AM transmitter, so you can use either NTSC or PAL. Audio, if used, is an FM sub carrier. Note that in the US you can't transmit on ANY TV channel. Not even under Part 15 rules. Video can only be transmitted by licensed broadcasters and Amateur Radio licensees. That being said... Don't expect to get any real range out a TV modulator like this. The picture will be quite snowy even when the transmitter is just a few feet away from the TV. You can do better by buying one of those 2.4 GHz camera and receiver combo with composite output. The video transmitter is FM. No snow (or very little). The range is a lot better, too. A solid 25 meters before the quality starts to fade.
Thaks for your advise. I already have 2.4ghz vtx and vrx. But this types of telemetry device are much expensive. But in this video, This transmitter much cheaper then other professional vtx. This analog vtx is for hobbies. Anyone can build there own tv/video transmitter.
Can I use any other RF module to build this transmitter. I have RF module in my old Sanyo TV laying idle in my house, can I use it ?
Also, can AV output of a digital camera work fine with this circuit?
No. You can use only this types of RF module which is directly send Av signal to the TV receiver. Av output of a digital camera also work like charm. Good luck
@@DiyTechBd
Thank you for your reply. Because am determined to replicate this project unfortunately I can't find an old VCD player but I found an old VCR player that has both RF input (antenna) and RF output(TV). Can this RF module work ? What other modifications can I make to make it work ?
Yes. It should be work. First, you have to identify the powe and video input terminal. 2nd, you have to determine the working voltage.
can i connect 12v in this transmitter
I did not tested yet. I think the ideal voltage should be Between 5-9 volt dc.
@@DiyTechBd i really want to connect this on 12v to transmit signal more farther radius
Then you can try 12v on your own risk.
if you increase the receiver battery e.g. 11v 1500 ma , the screen will be more detailed.
Thanks for your advise. I will try
Can we connect in mobile plz tell i need
This is important for we
What do you mean by connect in mobile?? I dont understand. If you have any questions, please leave them Below. I will try to answer Your questions. Thanks
@@DiyTechBd CAN i connect this transmitter in the mobile
No. You can only connect with tv.
@@DiyTechBd 😣😣😫😫 can you make a transmitter to connect in mobile
Ok. I will try.
Awsome bro sahi 🙏👍
Thanks brother.
What is the frequency of audio signal
Similar as Video signal's frequency. If you attache video and sound source on it. it will be transmit directly on tv with both audio and video signal like tv broadcast.
@@DiyTechBd I detected the frequency band. It is 95.5MHZ.
@@DiyTechBd what is its range?
I didn’t test yet. I think 100m in outdoor. Range also depends on antenna length.
@@DiyTechBd what is suitable length of antenna
Muy bueno se puede amplificar y mejoraria la calidad de imagen
I don’t understand your language. Plz text me in English.
usb camera kjvabe setup korbo dekhan jemon webcam
Sorry brother. Only analog camera/ analog video signal use korte parben jekono Source hote. Usb webcam digital. R webcam shora shori video signal o produce kore na. Er jonno specific decoder software use korte hoy pc te. Asha kori bujhate parsi.
Can I see it's footage in phone
If yes, than which app
No. You can't. Coz this have only analog signal
@@DiyTechBd toh kya aap koi mini camera banaa sakte hoo jiski footage haam mobile per dekh sake drone kai liya
Sorry dear. You should have to buy professional drone camera
@@DiyTechBd mera drone aak small drone hai vo iitna weight lift nahi kar sakta
Micro Fpv camera only 6 gram. I Think It's ok for your micro drone. Good luck
You have made an excellent project... C an you plz tell me how to make av output (offcourse, wired) instead of rf ???? I am keen to have your reply..
For av output from car rare view camera, you should have connect directly yellow(video) & black( GND ) cable to the AV port of TV receiver.
How to make a receiver
No need to built receiver. Just connect an external dipole antenna on TV. And search the frequency on any Channel
Good job,, BTW go ahead bro😍
Great work
Thanks 💕
Can i buy it
No dear. Not for sell
PAL-B/G ?
Both
Do we need permission from the government of India to broadcast if we have to broadcast inside a building?
I think it is legal in every country with limit Range.
Alright thank you :)
Bhai apna resiver kasabanaya ha
No need to build any external receiver. Directly tune on TV. Just connect an antenna on AV port of a Tv. And press the AV button on tv remote. The camera signal tune automatic on your tv through Av port
@@DiyTechBd ok thanks
Good job
Thanks
Good work
Thanks
Hi Sir, is 3,7 too much? And 2x 1,5v aa batteries? Thanks, make more videos!
No. For good result you should have to use 5v-9v instead of 3.7v
a project mujhe milage price
Not for sell bro.
Make a simple mobile 📱FM 🤔 transmitter 🇮🇳👍
Ok. I will try next time
@@DiyTechBd
Ok
you are amazing
Thanks.
Tell mee music name
Please Check on the description below
are you bangladeshi?
Yes I am.
Me too.🇧🇩
I'm a ece student and hell I can't figure out how u can't use a fluorescent as a antenna , just tell me it's a joke
no It's not a joke. Fluorescent tube acts like a bidirectional antenna
@@DiyTechBd damn I didn't know it's really unbelievable
Try it first. Then you will Believe
@@DiyTechBd I will try but I can't get such components like transmitter and a monitor
Is car cam is analog or digital?
Analog.
Sir hame Tv pe signal nahi arrre.
Increase the input voltage 3.7/4.2 volt to constant 5volt. Then try again. And use a telescopic antenna on tv jack or avr input tarminal. Yellow one is the video input on TV. If you connect an antenna on Avr terminal on your Tv. no need to tune tv channel. Just press the av button on your tv remote, You will get the video signal automatically.
One more question sir.
I have one old webcam can we use it to transmit video signals.
No. Coz Webcam produce digital signal. You need analog signal for transmit.
Good 👍 job
Thanks
What dvd model nombar
Actually I don’t know. All Most every cd/dvd player has this types of rf circuit.
No dvd player name and dvd model nombar
Panasonic
Player modal nombar
like by #wayank channel from indonesia
Thanks Buddy
Yes way!
Even if I plug this into a CRT TV, it's just still not getting the good quality that you deserve!
for good picture quality. You should have to increase the input voltage of transmitter up to 5v.
The modulators are designed to be plugged directly into the antenna input of televisions. They do not have the necessary power even to reach more than 10cm away.
This circuit is useless.
At first try it then talk.
Hey 3 tane bfr91 transistor kullanarak çıkış gücünü yükselt öyle konuş
Nice
Ben vcd video çıkış katından güçlendirerek 5km mesafeye gönderdim😂
Well done.
Very good
Thanks
lovely
Thanks
Thanks
You welcome
Super
Thanks
Real or fake?
100% real. you can try.
ক্যামেরাটার দাম কেমন হবে? এবং কোথায় পাবো?
Car accessories shop a paben. Price 350/450 taka theke Start.
@@DiyTechBd এটি ভারতীয় টাকাতে নাকি বাংলাদেশি তাকাতে? যদি বাংলাদেশি মুদ্রাতে তবে কত ভারতীয় মুদ্রায় পাওয়া যাবে?
আমাকে একটা বানায়ে দেন ৷ কত খরচ পরবে ?
Sorry.
@@DiyTechBd ekta radio transmitter banano dakhan please
OK. I will try
Not Bad !
Thanks
खाली घुमा घुमा के देखा से नही समझ में आता है बोल के भी बताओ कौन सा सर्किट कितने पॉवर का है
English plz.
This is a build in RF circuit of a vcd/dvd Player. You can find it on any old dvd/ vcd player.
Ohhh Man .. i can buy u a New Soldering Iron if these really works ... heheh
You can try. It's really work.This soldering iron is my favourite since 2006. Now i am waiting for a new one from you.🙂
@@DiyTechBd Oooohhkee! no probs . ill try that first : )
So where is my new soldering iron??
wow
👌
👍
The modulators are designed to be plugged directly into the antenna input of televisions. They do not have the necessary power even to reach more than 10cm away.
What you did is useless.
I think you need more study about analog rf transmitter. At first Try it then talk. This is a build in audio video transmitter circuit and its really work. Thanks
@@DiyTechBd I have been an Electronics Technician for almost 30 years. I tried that many years ago. IT DOES NOT WORK. The only way that will work is to add a couple of stages amplifying the output.
Good to know you. For short range no need to amplify the rf signal. I can challenge you. It’s 100% work. You should try again according to this video. By the way I am also an Engineer ( Bachelor of science in Electrical and Electronic Engineering).
Its car camera 😂 😂 😂 😂 😂 😂 😂 😂 lol
And great vid
Awesome bro
Keep it up brooo 😎
Yes dear. It is🙂
MASHAALLAH
Thanks
Is this legit?
Like will it work or not :| ?
100% Work.
@@DiyTechBd 1 more thing, where did you get that circuit board?
I get that circuit board from my old cd player
Ok
Op
What do you mean by Op??
*squinches eyes
It's not great 😣
100% work
zzzzzzzzzzzzzzzzzzzzzz
Zzz
L
F
👍👍👌🤏
Good job
Thanks