Diy Scissor Lift Table

แชร์
ฝัง
  • เผยแพร่เมื่อ 24 ธ.ค. 2024

ความคิดเห็น •

  • @SekAustria
    @SekAustria  5 ปีที่แล้ว +20

    the dimensions are available in my Patreon page www.patreon.com/posts/scissor-lift-24372931

    • @mototechtv.3774
      @mototechtv.3774 5 ปีที่แล้ว

      Sir saan po kau nkabili ng actuator

    • @dewaltxr7628
      @dewaltxr7628 5 ปีที่แล้ว

      Hanep hehe. Ok yung tiles kuya pede sa kusina yan. Di ko lng alam if pede yan pang worktable. Medyo manipis kc bakal at maliit.

    • @juanchopitti
      @juanchopitti 4 ปีที่แล้ว

      hello it have to pay to download the dimentions? sorry i dont understand how it works

    • @santycorrales
      @santycorrales 4 ปีที่แล้ว

      To high in lower position

    • @dasdas5725
      @dasdas5725 4 ปีที่แล้ว

      wow i want to give u 100 usd

  • @reloadnorth7722
    @reloadnorth7722 11 หลายเดือนก่อน +1

    Excellent work. I found my template. From Canada, Stay Safe and Vigilant.

  • @Nilezy
    @Nilezy 2 ปีที่แล้ว +3

    You need to add a safety mechanism. If those actuators fail when at full height, its' going to be a messy and danger disaster. Suggest a one way latch for the lower rolling mechanism that locks the top bed at intervals so if it fails, it will only drop to the last latch. You can make this unlatch when lowering and spring loaded with a return when it reaches the lowest position.

  • @TheHomePros6221
    @TheHomePros6221 2 ปีที่แล้ว +1

    Great build but I don’t like how u located the actuators you could have moved them back a lil bit so the table will fold up all the way to the ground and not raise up so high

  • @GiulianoAlessiani
    @GiulianoAlessiani 2 ปีที่แล้ว +2

    Nice flip flops

  • @jaspip1678
    @jaspip1678 5 ปีที่แล้ว +2

    Very good but why not make it so it goes all the way to floor?

    • @larssoerensen4978
      @larssoerensen4978 4 ปีที่แล้ว

      a scissorlift cannot raise the table from 0 deg position

    • @jaspip1678
      @jaspip1678 4 ปีที่แล้ว

      @@larssoerensen4978 that's why you put sides on it. When it sits flat on the floor the scissor is still at a slight positive degree.

  • @samjensen9873
    @samjensen9873 7 หลายเดือนก่อน

    Great video. Great design. I've been looking for something like this to learn how to put the bearings in correctly. My only suggestion would be adding some guarding on the outside of the bearing slots so that you dont accidentally pinch and crush your fingers as the table actuates up and down

  • @kurianthomas2350
    @kurianthomas2350 4 ปีที่แล้ว +2

    How much weight does the whole thing support.....200kg ???

  • @letslearnsomething30
    @letslearnsomething30 5 ปีที่แล้ว +1

    Thumbs up bro. Ang linis ng pag kakagawa

  • @leandersmith6184
    @leandersmith6184 ปีที่แล้ว

    How much kilo can the table hold?
    And the bottom rail can made so the frame rolls in and out while table goes up and down. So you won't trip over it.

  • @jm5710
    @jm5710 3 หลายเดือนก่อน +1

    Can you make a making video of Filmmaking Camera movement equipment, ( Telescopic Scissor Camera Jib Crane ) please?

  • @alexanderurezchenko6446
    @alexanderurezchenko6446 4 ปีที่แล้ว +5

    Hello, how are you going to use it? What is loading capacity?

  • @v-twintv471
    @v-twintv471 5 ปีที่แล้ว +1

    Chạy bằng xylinder điện khí nén ak anh. Có khỏe được như xylinder thủy lực không?

  • @danielnewkirk4731
    @danielnewkirk4731 4 ปีที่แล้ว

    I hope that isnt galvanized tubing you are welding?

  • @pragsharma8111
    @pragsharma8111 3 ปีที่แล้ว

    hi very nice .how much it coast .can guide me please from where you got parts.thanks

  • @CryptoWorld7507-f2h
    @CryptoWorld7507-f2h 2 ปีที่แล้ว

    @Sek Austria, where is the linear actuator connected so it can run? battery?

  • @mauriceeley621
    @mauriceeley621 5 ปีที่แล้ว +3

    How do you get your scooter / motorcycle onto the bench when it does,nt go down to the floor ?

    • @moimemesuis
      @moimemesuis 5 ปีที่แล้ว

      It never said it was for a scooter. This table is not designed for a motorcycle lift.

    • @jamesgoodwin2450
      @jamesgoodwin2450 5 ปีที่แล้ว

      maurice eley try reading the description

  • @poseidon3356
    @poseidon3356 4 ปีที่แล้ว +1

    Was ist das für ein Material?

  • @prasantapatro597
    @prasantapatro597 3 ปีที่แล้ว

    Dear friend can two people with 100 kgs stand on it?

  • @akileshs2652
    @akileshs2652 3 ปีที่แล้ว

    what is the type of bearing you used for wheel. share me a link

  • @eduki
    @eduki ปีที่แล้ว

    That's great. These linear actuators with pump are just electrical with screw inside, or are also hydraulic? Just wondering how many weight they could handle... Thank you!

  • @aksejtus
    @aksejtus 3 ปีที่แล้ว

    Para nagbebenta ba kayo ng ready to use?

  • @gagrinsingh100
    @gagrinsingh100 10 หลายเดือนก่อน

    Need drawing for installation of actuators

  • @tonex115
    @tonex115 4 ปีที่แล้ว

    Anong gamit mo dito na controller para sabay ang movement? May ganito ako ayaw nila sumabay.. mabilis ang isa kaysa sa isang acruator

  • @goisttv800
    @goisttv800 ปีที่แล้ว

    you can use it for motorcycle?

  • @viranegari6248
    @viranegari6248 5 ปีที่แล้ว +2

    I like your channel master

  • @robertcrowe984
    @robertcrowe984 2 ปีที่แล้ว

    What is the supplier of Electric motor for the lift table.

  • @saynomoremedia5674
    @saynomoremedia5674 2 ปีที่แล้ว

    what height 12v lifting pistons are they 20inch or higher thank you in advance

  • @recepcomert6820
    @recepcomert6820 6 หลายเดือนก่อน

    Mrhb kolay gelsin emeğine sağlık senden ricam olaçak profiller kaçlık kaçakaçlık profiller bilgi verirmisiniz ben yapacam motorlara bakım yapmak için motorsikletleri taşırmı😊

  • @AlrisSutan
    @AlrisSutan 2 หลายเดือนก่อน

    Di buat yg lebih besar seperti ini buat angkat mobil kuat nga ya..

  • @alanchuk8533
    @alanchuk8533 4 ปีที่แล้ว +1

    How much load capacity

  • @efrainciraco9670
    @efrainciraco9670 4 ปีที่แล้ว +1

    Hola me.podes pasar las medidas y que es lo que se nececita gracias

  • @gudvooy2
    @gudvooy2 3 ปีที่แล้ว

    Tnx for this video. I got an idea in making a wheel chair ramp for my car.

  • @dgb5820
    @dgb5820 4 ปีที่แล้ว

    You are a very clever man

  • @givemore605
    @givemore605 5 ปีที่แล้ว +7

    You are a champion, very professional, technical and precise in your work. Will be carrying your skills wherever I go

  • @mkpalermo945
    @mkpalermo945 3 ปีที่แล้ว

    Sir do you offer custom works?

  • @beniesenobs
    @beniesenobs 5 ปีที่แล้ว

    How could you even put the motorbike if it can't lay flat on it's wheels

  • @larssoerensen4978
    @larssoerensen4978 5 ปีที่แล้ว +6

    Hi - what is the length of the actuator when fully closed? I find no information on Banggood..

  • @mudharan
    @mudharan 4 ปีที่แล้ว

    What is the spec of hydraulic actuator used?

  • @bobetmotovlog9322
    @bobetmotovlog9322 3 ปีที่แล้ว

    Ang ganda ng output lodi solid

  • @kailashpaikra9015
    @kailashpaikra9015 4 ปีที่แล้ว

    Apka jack kaha se milega

  • @metalworkweldingfabricator5230
    @metalworkweldingfabricator5230 3 ปีที่แล้ว

    Kabakal tanong lang ano tawag jan sa jack na automatic mo saan mo siya ng nabili galing ng gawa mo naingit ako hehehe

  • @shanokhala
    @shanokhala 5 ปีที่แล้ว +2

    thanx, i always watch all yur vdos and learn a lot, thanx again

  • @pobydivers
    @pobydivers 4 ปีที่แล้ว

    So this lift weight limit is 200lbs. Right?

  • @devenbelanger8463
    @devenbelanger8463 5 ปีที่แล้ว +1

    Not bad but would be better if it sat all the way down. Maybe relocate the actuators?

  • @billybubba600
    @billybubba600 5 ปีที่แล้ว +3

    good job on the table. How much weight can it lift?

  • @xavierreivaxx
    @xavierreivaxx 5 ปีที่แล้ว +1

    How much is the cost per item??

  • @דודאשכנזי-ט4ע
    @דודאשכנזי-ט4ע 4 ปีที่แล้ว

    How much weight can it lift?

  • @kemmpatrickjalandoni7004
    @kemmpatrickjalandoni7004 5 ปีที่แล้ว +2

    where did you buy the hydraulic
    ?

    • @SekAustria
      @SekAustria  5 ปีที่แล้ว +1

      Its not hydraulic its motorized. Check my description i have a link there

  • @mrguide5748
    @mrguide5748 5 ปีที่แล้ว +1

    Có bán ko ah

  • @li7289
    @li7289 4 ปีที่แล้ว

    Are you able to make a smaller version from the ground up to 1M height? It is for a small child who can not walk to access an upper floor playhouse

  • @Sulaimantrichy
    @Sulaimantrichy 4 หลายเดือนก่อน

    Super work good working

  • @benzyblenaru9602
    @benzyblenaru9602 2 ปีที่แล้ว

    This 24 volt can be connected to a battery and also work outside the garage

  • @davidshelton5402
    @davidshelton5402 4 ปีที่แล้ว +2

    Great build, would be good, especially for working on ride on my mower, as I have a back injury.
    You've given me food for thought.

  • @spbse
    @spbse 5 ปีที่แล้ว +3

    Демо-вариантт. Хлипкая, как и почти все китайское. За идею - лайк.

  • @hannablom5803
    @hannablom5803 2 ปีที่แล้ว +3

    So cool!! Is it possible to put the linear actuator lower down so that the scissor lift is almost totally collapsed on the ground ( given that the stops you made was placed further away)- or does the linear actuator only lift the table if it is in a sloping degree?
    Thanks for your video! You did an awsome job!

    • @robertbutler8004
      @robertbutler8004 ปีที่แล้ว +1

      2hannablom5803 it would be possable but I do not know how there would be other people that is smarter than me that could do what you asked.This unit is way too high from the starting point.

  • @diegotejadamarquez2891
    @diegotejadamarquez2891 4 ปีที่แล้ว

    Hola, muy buena idea, pero yo acá en Colombia como consigo los actuadores, una descripción por favor, gracias

  • @madladpjl
    @madladpjl 5 ปีที่แล้ว +1

    how much weight can it lift up ? and great job

    • @SekAustria
      @SekAustria  5 ปีที่แล้ว +1

      Didnt test it. But it can lift most of things.

    • @madladpjl
      @madladpjl 5 ปีที่แล้ว

      was thinking of building one @@SekAustria

    • @SekAustria
      @SekAustria  5 ปีที่แล้ว

      Goodluck bro. :)

    • @charlesteddy7578
      @charlesteddy7578 5 ปีที่แล้ว

      @@SekAustria i was thinking you are building a hydrolic lift, i doubt if it could lift a bike for example.. or a person, what you think Sir?

    • @jeujopogo3433
      @jeujopogo3433 5 ปีที่แล้ว

      @@charlesteddy7578 ikea hack dinning table...

  • @joeabad5908
    @joeabad5908 5 ปีที่แล้ว +1

    Good workmanship.. Keep on building..

  • @sukhwinderpalsingh4562
    @sukhwinderpalsingh4562 4 ปีที่แล้ว +1

    VERY NICE FABRICATION SIR. WHICH CYLINDERS ARE YOU USING ?

  • @pnuttybutty723
    @pnuttybutty723 4 ปีที่แล้ว

    whats the weight limit

  • @rogeliogonzales6744
    @rogeliogonzales6744 5 ปีที่แล้ว +1

    anong amp setting nyo sa welding machine sir?and anong welding rod gamit nyo?mejo nahihirapan kasi ako pagweld ng mga maninipis,thanks

    • @SekAustria
      @SekAustria  5 ปีที่แล้ว

      80amp and 6013 rod

    • @tonyioannoni4951
      @tonyioannoni4951 ปีที่แล้ว

      @@SekAustria 80 amps and 6013 rod, its good for very thin material, what gauge were your tubing, if I would guess, around 1mm or 20 gauge, I guess you went for your needs, and built it accordingly, BUT the design is great, I am thinking of building one this summer, the dimensions will be pretty different, and I probably use 1/4 inch tubing, but I am not yet settled with the lift mechanism, there are 3 possible methods, linear actuators, hydraulic pump or large threaded rod and screw, 2 of the actuators I have push 600 pounds each and for 22 inches...what made you chose actuators???

  • @shivamaroranawabganj1050
    @shivamaroranawabganj1050 4 ปีที่แล้ว

    How many kg can it can lift

  • @SekAustria
    @SekAustria  5 ปีที่แล้ว +8

    dimensions of this project will be posted on my patreon page soon. thanks and have a great day guys :D

    • @jonathanfernandes1242
      @jonathanfernandes1242 5 ปีที่แล้ว

      great build, very neat craftsmanship.... what is the payload capacity this design can handle.....

  • @bseant420
    @bseant420 4 ปีที่แล้ว +1

    i am going to build this. great video. except those tile pieces need a backer? they will just crack on their own.

  • @psalmboy_outdoor
    @psalmboy_outdoor ปีที่แล้ว

    Mga magkano inabot yung table?

  • @danielvandertorre7505
    @danielvandertorre7505 5 ปีที่แล้ว +1

    very professional work

    • @dasdas5725
      @dasdas5725 4 ปีที่แล้ว

      he is like a pro

  • @dattarajlawande5662
    @dattarajlawande5662 4 ปีที่แล้ว

    Can u tell us what is size and thickness of section used...?

  • @CristopherBombita
    @CristopherBombita 11 หลายเดือนก่อน

    San po nakakabili Ng hydolic nyan

  • @dipakagarwal9476
    @dipakagarwal9476 5 ปีที่แล้ว +1

    I want to build a table for industrial use with capacity to lift up to 1000kgs and at a height of 40 inches.
    Which calendar or piston shall I use and how many.

    • @SekAustria
      @SekAustria  5 ปีที่แล้ว +1

      Use a hydraulic one

  • @blessedalfredquansah4532
    @blessedalfredquansah4532 4 ปีที่แล้ว

    Hello....can i buy it?

  • @gadgetsgimmicksandtech
    @gadgetsgimmicksandtech 3 ปีที่แล้ว +1

    Nice build - what is the total cost for parts on this? I gave up with my stick welder and went flux core wire welding now - much easier! What is the load capacity for the table?

  • @iiXi-nz7cm
    @iiXi-nz7cm 3 ปีที่แล้ว

    What type of power supply for the actuator did u used?

  • @mojloginjuzzajety4071
    @mojloginjuzzajety4071 3 ปีที่แล้ว

    1. Very nice welding.
    2. But, like many other comments: some support seems neccessary under the tiles
    3. Why the actuator was put there? It limits the range (initial height is quite high) and puts very high load on the starting point: the lever works against it.

  • @павелсоловьев-э4п
    @павелсоловьев-э4п 5 ปีที่แล้ว +1

    Well done. But I'd like to know what the purpose of this device.

    • @lionhec
      @lionhec 5 ปีที่แล้ว

      Same question. What is it for?

    • @MrPhatNOB
      @MrPhatNOB 5 ปีที่แล้ว

      павел соловьев
      A height adjustable workbench. Perhaps to adjust to optimal height depending on the project in order to prevent worker fatigue/strain ect.
      Also handy for moving awkward or heavy projects about and lifting them to a particular height.

    • @павелсоловьев-э4п
      @павелсоловьев-э4п 5 ปีที่แล้ว

      @@MrPhatNOB what about carrying of this device?

    • @MrPhatNOB
      @MrPhatNOB 5 ปีที่แล้ว

      павел соловьев
      Carrying capacity or actually carrying the device around?
      Not sure about the capacity, maybe 50kg or so according to the specs of the actuator.
      As for moving the table, it’s on castors so I say you just wheel it around the workshop then lock the castors when it stops.

  • @tantan4662
    @tantan4662 3 ปีที่แล้ว

    Best Project Dude 🤗🤭👏👌

  • @bigrockets
    @bigrockets 5 ปีที่แล้ว

    not sure what he intends to put or lift on this table? has a limited range of motion for putting something on it such as a motorcycle? nice job on the build however its too bad it doesnt go down lower.

  • @irohnperpedia4958
    @irohnperpedia4958 5 ปีที่แล้ว +1

    Ayus idol quality pagkakagawa

  • @tomsdreamshopworx
    @tomsdreamshopworx 5 ปีที่แล้ว +20

    Is the steel galvanized? If so, the fumes from welding it are very bad for you. You should grind the steel around the weld first to remove the galvanized coating. Pleas be careful. Also, as someone else said, The tiles look very fragile and are not designed to support any weight. They are designed to late flat on the floor below them.

    • @kazykamakaze131
      @kazykamakaze131 5 ปีที่แล้ว +1

      Just use a respirator in a ventilated area. No need to grind anything then. In any case you should always wear a respirator welding/grinding ect anyting metal related generally rule of thumb is use a respirator.

    • @Tsalinger
      @Tsalinger 5 ปีที่แล้ว

      He's stick welding aluminum genius. His big issue is that he didn't super clean the joints before welding.

    • @tomsdreamshopworx
      @tomsdreamshopworx 5 ปีที่แล้ว +2

      T salinger1026 - I am not a welding expert, but I’m pretty sure the caster plates are steel as is the small square stock he used to guide the sides of the bearings. Please search down in the comments were Toro Bravo asks if it is steel or aluminum. His response is “iron”.

    • @J1I9M7M4Y
      @J1I9M7M4Y 5 ปีที่แล้ว +4

      @@Tsalinger Wow, you really know stuff.. 😂 (not really, totally clueless)

    • @J1I9M7M4Y
      @J1I9M7M4Y 5 ปีที่แล้ว

      @Y T Uhm.. Im not sure i understand what you´re talking about?!

  • @enklum
    @enklum 5 ปีที่แล้ว +7

    Really nice job
    You better have to add some supports underneath the tiles, or it will break very quickly

    • @tomsdreamshopworx
      @tomsdreamshopworx 5 ปีที่แล้ว +1

      I agree!

    • @g.e.o.r.g.e...
      @g.e.o.r.g.e... 5 ปีที่แล้ว

      They look like some kind of fiber cement board. They aren't regular porcelain or ceramic.

    • @brettpeters5777
      @brettpeters5777 4 ปีที่แล้ว +2

      @@g.e.o.r.g.e... they are ceramics im a tiler by trade the only thing id suggest is to add another support under the centre of those tiles especially for a road bike application

    • @g.e.o.r.g.e...
      @g.e.o.r.g.e... 4 ปีที่แล้ว

      @@brettpeters5777 so you're saying the fibers we can clearly see are just decorative?

    • @andrewsantos171
      @andrewsantos171 4 ปีที่แล้ว +1

      I noticed that also the tiles.even if he add sipport on that still breaks.maybe 1inch plywood then a thin metal plate on the surface

  • @arthurconrod9825
    @arthurconrod9825 5 ปีที่แล้ว +1

    is this a heavy duty massage table.

    • @liamfahey6110
      @liamfahey6110 5 ปีที่แล้ว

      I wouldn't sit on it in a fit

  • @luisvera9539
    @luisvera9539 4 ปีที่แล้ว +1

    Donde se puede comprar esos brazos hidráulicos? Desde ya gracias.

  • @soobokkim7782
    @soobokkim7782 3 ปีที่แล้ว

    Great help. My imagination materialized. Thanks

  • @bra_nkay7756
    @bra_nkay7756 4 ปีที่แล้ว

    What is the full length description of the linear actuator?

  • @backpackstories5766
    @backpackstories5766 4 ปีที่แล้ว +1

    if sa sasakyan po anong materiales kailangan?

    • @SekAustria
      @SekAustria  4 ปีที่แล้ว

      Gumamit kanalang ng winch or hydraulic. Mahina lang mga actuator nayan

  • @michelboisvert5684
    @michelboisvert5684 4 ปีที่แล้ว

    hi, what are you putting on there, I hope it's not a lawn tractor because you're missing height, your folding table doesn't go all the way to the ground.

  • @Purowalangkwenta
    @Purowalangkwenta 4 ปีที่แล้ว

    depende kung gaano ka lakas yung Linear actuator. pang magagaang na bikes pwede yan. bag malalaki di kaya

  • @Zoreil0683
    @Zoreil0683 4 ปีที่แล้ว

    Very good job !!! Congrat

  • @ledinhanh
    @ledinhanh 5 ปีที่แล้ว +1

    nice video

  • @richardwomack9196
    @richardwomack9196 5 ปีที่แล้ว +1

    60mmx60mm Tiles? Looks more like 60cm to me and we don't use the metric system.

  • @bidouilleheure
    @bidouilleheure 4 ปีที่แล้ว

    Hello how did you manage to drive the cylinders

  • @maxhammontree3169
    @maxhammontree3169 2 ปีที่แล้ว

    Looks great. Will it hold any weight?

  • @etenor
    @etenor 3 ปีที่แล้ว

    hello, I love what you are doing, I would like to do the same, can you please tell me what are the reference of your linear actuator,
    I have 2, of 12 volts which are the same but smaller with 300 mms and 400N .. yours seem the good power, by thanking you.
    good to you

  • @fabrizio9022
    @fabrizio9022 5 ปีที่แล้ว +2

    very nice job! i like it!

  • @lcf4359
    @lcf4359 5 ปีที่แล้ว +1

    Can you give me all the mats used not the dimensions

  • @Bite0fBread
    @Bite0fBread 5 ปีที่แล้ว +1

    What Welding Machine are you using???

  • @paatsankhan8504
    @paatsankhan8504 5 ปีที่แล้ว +2

    sir this remp full size tell four pipe side engaged in his size what o

  • @hzx6n9
    @hzx6n9 5 ปีที่แล้ว +1

    Destination??????

  • @fernandojunior2343
    @fernandojunior2343 5 ปีที่แล้ว +1

    How much load this lift you made support?

  • @TPL034
    @TPL034 2 ปีที่แล้ว

    Hi Sir, I’m one of your kababayang pinoy. Sir I would to ask some tips on how to install a proper wiring on “linear actuator” that you used regarding with this video. It’s a big help for me sir as a beginner who want to be a pro someday on Welding Industry.