Love my tiny hawk race. Chopped my vtx antenna clean off after a wreck and was struggling to figure out what antenna would work for a replacement im only 2 months into the hobby but i figured out acro mode for the most part but learning flips and power loops sometimes end up in mean crash. Great video man. Its put me at ease.
I'm learning to solder and stuff AND how to fly drones. I love my TH2FS but I've slowly been upgrading it with 3D printed stuff. The VTX antenna is my next feat after I get soldering down. I've got the little ufl connectors coming, too. I plan on just soldering one of those on so I can upgrade the antenna easier later on. I have a foxeer lollipop for the time being, I'm going to eventually get a AXII mini lollipop. This way, once I get that new one, I can just pop the old one off and slap the new one on. Thanks for the video. Shows me that the board can, in fact, take the little ufl connector pad.
Hi! I have a TH2 Race also and the VTX antenna has been partly chopped off from the props and also from a crash. I use the Emax Transporter FPV Goggles 5.8G and I was wondering if that VTX antenna upgrade would still work with these goggles? If I use 5.8G antenna to connect to the goggles, I figured that it would do the trick, but since I am pretty new to FPV, I wanted to make sure. Thanks for your help!
Hello, I replaced the default VTX antenna in my Tinyhawk Race 2 with the same Micro AXII RHCP as you. I also replaced the receiver antenna with a new one (31.2mm of centre wire exposed). I'm now getting better image quality, but the signal is really bad. If my quad flies 5m behind me, I automatically lose the signal. Same if in front of me but slightly larger range. Help is so much appreciated
Careful does it ladies and gentlemen. I just broke my VTX(grey screen) with this operation. I thought myself pretty proficient at soldering and it seemed like it went off without a hitch but now I'm scrambling to replace my VTX. Don't be dissuaded, life is about trying new things just understand what you might be losing and be prepared to rectify and restore.
Just take your time and make sure you have a good tip and good solder and you'll do fine :-). If You enjoyed the video a sub to my channel is appreciated!
Hi, I lost the antenna and the little tiny pad in a crash. Then, I am not able to solder again a new antena to the vtx :( I think I have to replace the vtx. Can I do the vtx mod on the tinyhawk II race?
Hello, my tinyhawk 2 race had crashed little bit. After that, much jello phenomenon appears more and more on my goggle screen. Do you know how to fix it??
Nice video ! I might have to try this mod for my tiny hawk 2 race. I can’t find stock props anywhere, every place I check online is sold out. Do you know anywhere I could buy new props? I’ve tried the gemfan props and they are terrible. One crash or hard landing and they are toast. Any recommendations on good props for this thing?
@@DoRC Fair play, I'm still new to FPV, just killed my Freestyle with a crash, and don't trust my soldering skills to fix/upgrade. Will try the Freestyle 2, and use the spare parts from the original to try some mods eventually.
Bonjour superbe bravo belle vidéo l'ami, je viens de découvrir ta chaine superbe bien je m'abonne dut coup👍moi même je vient d'ouvrir ma chaine vtt et un autre loisir je t'invité a venir si tu le souhaite découvrir ma petit chaine et n'hésite pas a me dire se que tu en pense :) bonne sortie vtt à toi et merci pour ton travaille vidéo superbe bien bravo🚴 l'amie 👍 😀🌈
I always saw pictures of the final quad with everything on but no close up to show how to accomplish this. Thank you so much for making this!
Glad to help!
Love my tiny hawk race. Chopped my vtx antenna clean off after a wreck and was struggling to figure out what antenna would work for a replacement im only 2 months into the hobby but i figured out acro mode for the most part but learning flips and power loops sometimes end up in mean crash. Great video man. Its put me at ease.
Also maybe consider leaving a link to the antenna in the video description.
I don't like leaving links but you should be able to Google it pretty easily:)
As a cable tech i dont suggest soldering your inside coax. Great job on the soldering. Love your videos!
How would I attach it to the solder pad on the board?
@@DoRC I mean like internet coax cable. I have seen alot in my job. Just joking around with you.
I recommend running the shielding back the other way to expose less of the center wire.
I'm learning to solder and stuff AND how to fly drones. I love my TH2FS but I've slowly been upgrading it with 3D printed stuff. The VTX antenna is my next feat after I get soldering down. I've got the little ufl connectors coming, too. I plan on just soldering one of those on so I can upgrade the antenna easier later on. I have a foxeer lollipop for the time being, I'm going to eventually get a AXII mini lollipop. This way, once I get that new one, I can just pop the old one off and slap the new one on. Thanks for the video. Shows me that the board can, in fact, take the little ufl connector pad.
Nice vid, thanks, i have no problem with the vtx, but i put a xm+ and have good range now, i love that little ripper.
Hi! I have a TH2 Race also and the VTX antenna has been partly chopped off from the props and also from a crash. I use the Emax Transporter FPV Goggles 5.8G and I was wondering if that VTX antenna upgrade would still work with these goggles? If I use 5.8G antenna to connect to the goggles, I figured that it would do the trick, but since I am pretty new to FPV, I wanted to make sure. Thanks for your help!
Hello, I replaced the default VTX antenna in my Tinyhawk Race 2 with the same Micro AXII RHCP as you. I also replaced the receiver antenna with a new one (31.2mm of centre wire exposed). I'm now getting better image quality, but the signal is really bad. If my quad flies 5m behind me, I automatically lose the signal. Same if in front of me but slightly larger range.
Help is so much appreciated
Careful does it ladies and gentlemen. I just broke my VTX(grey screen) with this operation. I thought myself pretty proficient at soldering and it seemed like it went off without a hitch but now I'm scrambling to replace my VTX. Don't be dissuaded, life is about trying new things just understand what you might be losing and be prepared to rectify and restore.
Yeah this is a fairly finicky soldering job for sure. A sub is appreciated :-)
My antenna came off in a crash. I've never soldered before. Wish me luck :(
Just take your time and make sure you have a good tip and good solder and you'll do fine :-). If You enjoyed the video a sub to my channel is appreciated!
Nicely done video! Love the channel. Thanks for the tip. Happy flying.
Thanks!
@@DoRC You're welcome!
Hi, I lost the antenna and the little tiny pad in a crash. Then, I am not able to solder again a new antena to the vtx :( I think I have to replace the vtx. Can I do the vtx mod on the tinyhawk II race?
Yes. It has the same fc as the tinyhawk freestyle. You just need to make sure you have enough room under the canopy.
Would it be worth it/possible to solder a u.fl connector to the VTX to make it easier to attach/switch antennae?
Is it possible to soilder an xt60 as my parallel charger is all xt60 plugs ? New to this lol
Nice video!
You would like to see my homemade 1/5 49cc RC buggy!
Hello, my tinyhawk 2 race had crashed little bit. After that, much jello phenomenon appears more and more on my goggle screen.
Do you know how to fix it??
First thing to check is if the camera itself is loose. Let me know if that's the issue!
Awesome drone video...
Thanks:)
Nice video ! I might have to try this mod for my tiny hawk 2 race. I can’t find stock props anywhere, every place I check online is sold out. Do you know anywhere I could buy new props? I’ve tried the gemfan props and they are terrible. One crash or hard landing and they are toast. Any recommendations on good props for this thing?
I've only used the stock props so I can't give you suggestions. Sorry. Thanks for watching a a sub is appreciated!
I found some for sale on emax website. Thank you. Good video
What camera is this? A Nano 3? Thinking about change the camera cause the nano3 is much lighter
No it's a foxeer nano toothless.
@@DoRC okay thank you!
Awesome Channel I subbed!
Thanks!
Nice! Are you planning on picking up the Freestyle 2?
No. It's a nice quad but I already modded my freestyle to higher specs:)
@@DoRC Fair play, I'm still new to FPV, just killed my Freestyle with a crash, and don't trust my soldering skills to fix/upgrade. Will try the Freestyle 2, and use the spare parts from the original to try some mods eventually.
Dam
I'm an idiot
I missed up the antennas
Soldered the wrong one 🥴
big like from Xpertboost. keep it up. love your videos. new subscriber here.
Do you think I can cram a runcam split nano on this setup?
Yea I did
You micht have to cut a little of the camera holder tho
Just to allow it to stretch a little
I might do this to my TH2 Freestyle :) THX
Good man good man !
Cool
Thanks. I'm doing surface videos for a while so if you're interested in those be sure to subscribe and check them out :-)
cool bro
subbed man
🖐️🤠👍
:)
2:05 glad it's not your dog......
Bonjour superbe bravo belle vidéo l'ami, je viens de découvrir ta chaine superbe bien je m'abonne dut coup👍moi même je vient d'ouvrir ma chaine vtt et un autre loisir je t'invité a venir si tu le souhaite découvrir ma petit chaine et n'hésite pas a me dire se que tu en pense :) bonne sortie vtt à toi et merci pour ton travaille vidéo superbe bien bravo🚴 l'amie 👍 😀🌈