This is really cool idea. One thing I would do differently though, I would add a chain cover. If you throw a chain from a worn out link it might take some skin with it if the chain fliys off of the sprocket just right.
A nice illustration of some mechanical principles - thank you. One of the more subtle issues is that more gearing is required because the centrifugal clutches are more of an on-off device, only fully engaging at over half the full rev range. This means that without the correct set of ratios they are always slipping or only work with downhill / gravity assistance, and a push start is absolutely needed. Am gonna have a go at a 3 or 5 speed rear internal geared hub 4 stroke engine version.
I really love how you showed us that motor all hooked up to nothing just vibrating and purring on the table. It's a raw obtainable cheap efficient power source. So many ideas. Could I power 4 wheels with 4 motors? Can you combine multiple motor powers like 3 motors to 1 wheel? Magical stuff man.
I have done those scooters back in the past 3 decades ago. You would have to change the sprocket ratio I believe right now your scooter won't move stand still you will have to push first to get it started especially with the clutch still on it. Also the clutch will burn out. The best way is to remove the clutch weld the lug nut on the motor shaft place the motor as closest possible to the tire with the lug nut firmly pressed against the tire weld motor in place and you're done.(you may have to fill up the tire with more air pressure) to start the motor you have to do is stand on the scooter with one foot with the other push yourself into the motor start and you'll keep driving you will hit about 20 to 25mph guaranteed
I have a near-identical engine in a powered earth auger (drills holes in the ground) and I agree with you: When it hits a rock, I reckon the kick from it could easily break your wrist of you weren't holding it the right way. I think that we all tend to forget just got powerful even small engines can be...
Wow...look at the expertise of armchair fabricators out there. I don’t know how they carry around the burden of so much wisdom 😂. Nice build - way to be resourceful with what you got 👍🏼
His home had refuse recycling. Hardly a young man of poverty and no means. But yeah, he uses his head. The scooter works and he inspired some kids that now want a stick welder, cutoff saw and drill press. You need the tools to build your dreams.
Hey man great job on using what you got and making a solid simple project I don't give a crap what people say on this you make do with what you got and you did and it looks good and functions.
incredible project if I were I would replace the platinum with a used one and send it to a mechanical turner to machine a flange to fit the pinion for the chain pinion and crown ratio kit I would never cut but It was sensational amazing job
Сразу видно что автор не вдавался в рассчёты, из-за этого самокат еле едит и движок только палит сцепление, а нормально разогнать никогда не получится. Проблема в слишком большой ведущей звезже, максимум она должна быть на 8 зубьев, но лучше 6. Сварка это отдельная тема и долго она не проживёт. Для того чтобы пластину на которой крепится двигатель не оторвало в первые минуты, нужно было приварить несколько расскосов.
Hey love the vid!! Do you think with a different gear ratio, you could go faster? I was thinking you could even use a bike cassette with several gears and you could have a manual shifter
Yeah, i was thinking the same. I even think i want to try installing battery/starter/sound system/alternator/proper seat/roof/mini fan/etc etc hahahaha..
Since this video covered needed aspects of the project, I'm not criticizing in any way ''at all'', but simply suggesting. I might've added a brace or braces to that vertical motor mount plate to help prevent your welds from cracking due to motor or bumpy road vibrations, however, since the frame was obviously heavy enough gauge steel that you could use a ''stick welder'', it may not matter. Instead of that plate, I may've welded another plate onto the frame to bolt the motor mount plate onto & added some slots to 1 of the plates so you could adjust the motor's position for whatever reason. Since you added that chain tension idler, the slots may not be needed to adjust your motor whichever way it ''might'' be needed . A very simple, yet excellent build. I've been wanting to build a 4-wheeled version of ''something'' powered with a weed-eater or chainsaw engine. I've torn apart chainsaws & know their drive setup, but since I haven't got around to tearing into 1 of these things yet, I wasn't sure what all was in 1 so this video was ''VERY BENEFICIAL'' in showing how simple the things are. GREAT JOB & GREAT VIDEO, SIR.
...ни фига себе!-, чё придумал!-, отличный получился мотосамокат!-, необходимо будет доделывать до ума:-ставить крылья над колёсами, кожух на цепь ну и конечно же покрасить!!!
Definitely cool and awesome if you to share the video to inspire and teach others how to do something like this. But be careful it would hurt to fall at that top speed of 3.5 miles per hour
Thank you I’m building somthing different a mini car and you helped me find out how to make the wheel move because I didn’t know I had to make the bolt thing for the chain had to be connected to wheel and spin with the wheel
nice vid hopefully you need to put a reinforcement steel bar on the side of the motor in addition more improvising for the ped itself. ride safe out there! and by nice motor you have ❤
The single plate needs more reinforcement to be a robust design. Currently, there is too much flexing and bending and welds be breaking at the bottom frame rails.
если не ошибаюсь, то при такой передаче и оборотах в среднем 4500 в минуту....скорость самоката будет около 60-70 км час или буксовать сцепление..поездишь недолго.. шестерня напрямую....значит средние обороты 4500 минимум... это в минуту.. умножим обороты на 60 минут в часе...разделим передаточное на 3, приблизительно... возьмем 10 дюймовое колесо где-то 0,75 метра на оборот... итого 4500*60=270000 затем делим на 3 =90000 умножаем на длину 0,75 и делим на тысячу =67,5 средняя скорость...ну как то не реально....точнее немыслимо...плюс подшипник быстро выйдет из строя
Dang!thats gonna be awfully high geared!For a little motor,I would use as small of a sprocket on the clutch as I could find,like 10 or 11 tooth,so it will have good takeoff.(shoes and a rear brake would be advised...just sayin')
This is really cool idea. One thing I would do differently though, I would add a chain cover. If you throw a chain from a worn out link it might take some skin with it if the chain fliys off of the sprocket just right.
Df
You used what you had and made something awesome, I respect it
Dude that's awesome, on top of that, you're probably the only one who actually showed us what you were doing. Thanks :)
Zz
A nice illustration of some mechanical principles - thank you. One of the more subtle issues is that more gearing is required because the centrifugal clutches are more of an on-off device, only fully engaging at over half the full rev range. This means that without the correct set of ratios they are always slipping or only work with downhill / gravity assistance, and a push start is absolutely needed.
Am gonna have a go at a 3 or 5 speed rear internal geared hub 4 stroke engine version.
Excellent project 👍
I really love how you showed us that motor all hooked up to nothing just vibrating and purring on the table. It's a raw obtainable cheap efficient power source. So many ideas.
Could I power 4 wheels with 4 motors? Can you combine multiple motor powers like 3 motors to 1 wheel? Magical stuff man.
Shut up guys
Nvm
Hanya hanyah hshshc
T-)sk
Oo
Amazingly clever 👍🏻
I have done those scooters back in the past 3 decades ago. You would have to change the sprocket ratio I believe right now your scooter won't move stand still you will have to push first to get it started especially with the clutch still on it. Also the clutch will burn out.
The best way is to remove the clutch weld the lug nut on the motor shaft place the motor as closest possible to the tire with the lug nut firmly pressed against the tire weld motor in place and you're done.(you may have to fill up the tire with more air pressure) to start the motor you have to do is stand on the scooter with one foot with the other push yourself into the motor start and you'll keep driving you will hit about 20 to 25mph guaranteed
Pretty neat nice video 👍
62cc string trimmer? Wow, that’s “Shaking hands with danger”..... I love it
I have a near-identical engine in a powered earth auger (drills holes in the ground) and I agree with you: When it hits a rock, I reckon the kick from it could easily break your wrist of you weren't holding it the right way. I think that we all tend to forget just got powerful even small engines can be...
What Kindve speed you get?
My kll see
There are scooters with smaller engines 💀💀
Классная идея! Советую сделать Защиты на случай разрыва цепи.
I like this scooter great job. I'd only recommend a chain guard. Hope you are still enjoying it after about a year!
thanks man I needed this gave me some thoughts about my 3 wheel trike
He can he. Ja. Be cue. Know. Byword. Cush yo he bugs. Ions. Bhsojs. He I x
สุดยอดครับผมจะทำใช้บ้าง
Wow...look at the expertise of armchair fabricators out there. I don’t know how they carry around the burden of so much wisdom 😂. Nice build - way to be resourceful with what you got 👍🏼
Thank you ❤️😂
🤔🤓🤓🤓🤓🤓👊
His home had refuse recycling. Hardly a young man of poverty and no means.
But yeah, he uses his head. The scooter works and he inspired some kids that now want a stick welder, cutoff saw and drill press. You need the tools to build your dreams.
Next project honda ivtec and turbo?
Mr IMBUS How fast?
Thank you for the idea, will be doing something similar soon 👍🏼
very good !! I also made one with a 150cc engine
Hey man great job on using what you got and making a solid simple project I don't give a crap what people say on this you make do with what you got and you did and it looks good and functions.
Welding over paint, a true DIY'er
really cool. how did you build the back wheel? i wonder how to put a gear on mine.
Маленькая скорость.А ещё сиденье надо, а вообщем неплохо.А главное своими руками, а не куплено в магазине. И ведь это радует!
The burnout was the next finishing touch, awesome
Kopp kopp kopp kip i9 on o ok pop ok ok
No, it was just ridiculous.
Great job 👍👍👍
what do i watch at 1 am:
Good work but as they have mentioned you have to put smaller sproket8 to avoid clutch slipping and wear
Hello, have a question is it needed to put the engine a bit up or we can put it on the frame close to the wheel?
incredible project if I were I would replace the platinum with a used one and send it to a mechanical turner to machine a flange to fit the pinion for the chain pinion and crown ratio kit I would never cut but It was sensational amazing job
Thank you!
I love the brake stand burn out!
"...CROCKS! HE'S WEARING CROCKS! YOU'RE DRIVING THIS SMOKE HOUSE AROUND ON A SCOOTER... WITH CROCKS???"
From SNL sinkhole skit.
Have you had a decent wipeout?
great video
Great job
Need to put a roller on to keep the chain tension but solid first little diy build
hello. interesting video well done, but please tell me why the star that is attached to the gearbox? Thanks.
Gooddddd
Nice ... Joint silencer ..
Love from India
can i know which engine you have usen
You need to put a smaller sprocket on engine to allow it to rev higher. That should be going a lot faster for a 62cc engine
Сразу видно что автор не вдавался в рассчёты, из-за этого самокат еле едит и движок только палит сцепление, а нормально разогнать никогда не получится. Проблема в слишком большой ведущей звезже, максимум она должна быть на 8 зубьев, но лучше 6. Сварка это отдельная тема и долго она не проживёт. Для того чтобы пластину на которой крепится двигатель не оторвало в первые минуты, нужно было приварить несколько расскосов.
@@TomRaily d
@@TomRaily no. Th-2uv
Hes probably got it geared down
@@luismartinez4081
Awesome!! If I could add one thing as a scooter designer? I'd mount the all 4 bolts to the engine. It'll last a lot longer .
Will you please include links to Amazon for the back wheel
Nice
I have taken inspiration to this design and made it an L bracket that screws in just like yours does.
Зажёг резину!Крутяк!
mother of invention, love when a great idea comes together god bless
Это сцепление где звёздочка приварена не расчитано на боковое давление цепи, долго не прослужит. Но лайк за труд
👍🤝
Next Elon Musk for sure...
Very cool
Nice project 👍
What type of rear tire did he use and what type of brakes did he use
Very smart and clear video!!! Does that kind of engine have a centrifugal clutch? (It seemed to me) thank you!!!
its a commercial strimmer engine they all have that clutch bud
Hey love the vid!! Do you think with a different gear ratio, you could go faster? I was thinking you could even use a bike cassette with several gears and you could have a manual shifter
Yeah, i was thinking the same. I even think i want to try installing battery/starter/sound system/alternator/proper seat/roof/mini fan/etc etc hahahaha..
Bracket holding engine should have been designed to cover all the 4 screws
or on both sides
This is a great quick and easy diy project for me and my 8yo boy this spring thanks a million and keep up the good work my brother god bless all
A
Can i have your parts list?
it's a nice project, can you share the scooter dimensions, good work
Any ideas on how to trick out my powerchair i have a 1450d jazzy ??
I meed some ideas since im always in it.
Predator 670cc v-twin! 😂😂😂
Andrew Savage 😂💀
@@andrewsavage1872 dobladora de ángulo
Колесо от садовой тачки. А ось какая?
Would of liked to see the wheel set up
Since this video covered needed aspects of the project, I'm not criticizing in any way ''at all'', but simply suggesting. I might've added a brace or braces to that vertical motor mount plate to help prevent your welds from cracking due to motor or bumpy road vibrations, however, since the frame was obviously heavy enough gauge steel that you could use a ''stick welder'', it may not matter. Instead of that plate, I may've welded another plate onto the frame to bolt the motor mount plate onto & added some slots to 1 of the plates so you could adjust the motor's position for whatever reason. Since you added that chain tension idler, the slots may not be needed to adjust your motor whichever way it ''might'' be needed . A very simple, yet excellent build. I've been wanting to build a 4-wheeled version of ''something'' powered with a weed-eater or chainsaw engine. I've torn apart chainsaws & know their drive setup, but since I haven't got around to tearing into 1 of these things yet, I wasn't sure what all was in 1 so this video was ''VERY BENEFICIAL'' in showing how simple the things are. GREAT JOB & GREAT VIDEO, SIR.
ЗАПУЛА
I have an idea and I want to develop it and need your help I would like to visit you
Wow
... Forward
excelente trabajo,yo usaria un piñon de bicicleta,y no haria ese desgaste innecesario al neumatico al final del video.felicitaciones
Сыроват конечно и не продуман агрегат, но в целом дети будут довольны.
Согласен
А ты сам то что нибудь собрал?
@@user-vt2iv7xp5l да. А ты?
...ни фига себе!-, чё придумал!-, отличный получился мотосамокат!-, необходимо будет доделывать до ума:-ставить крылья над колёсами, кожух на цепь ну и конечно же покрасить!!!
Would it go faster with a smaller sprocket on the wheel or would it be more strain on the motor and end up going slower?
A smaller sprocket on the wheel would result in less torque but could spin faster
Definitely cool and awesome if you to share the video to inspire and teach others how to do something like this. But be careful it would hurt to fall at that top speed of 3.5 miles per hour
Que velocidade andar tão rápido assim me dá até estresse desse dele e saio caminhando
Сцепление сразу развалилось? Вал то на одном подшипнике
Nice build ! 👍
Nice machine
😋👍👍👍
Wouldn't it over heat?
😯👍
Where did you get the rear sprocket on the wheel ?
Whelp, know Ik what to do with my old weed Wacker. Turn it to an epic go-kart/motor bike
I won't go very fast so I suggest selling it to make money for a pred engine
Hey what's the top speed on this awesome build
Wow amazing love it
Thank you I’m building somthing different a mini car and you helped me find out how to make the wheel move because I didn’t know I had to make the bolt thing for the chain had to be connected to wheel and spin with the wheel
Хрошый самокат неодин ласик Радом нестоял 👍,акитайский самокат .
what direction does your engine rotate when viewed from the clutch side when running? clockwise or anti clockswise.
Counter-clockwise
Can you tell me where you got the motor mounts? I purchase one of these motors, but it didn’t have a mount included
Why you weld with our removing the paint tho 🤦🏻♂️
6011 can burn it off 🤘👍😎
@@briantruck2284 or 6010
@@briantruck2284 thx inform
Smaller sprocket on the engine required, this is just riding/slipping the clutch all the time.
Na it just has very short hearing the back sprocket needs to be smaller
needs smaller front sprocket OR larger rear sprocket !
Hopeless gearing ratio !!anyone that has done this are laughing 😂
Top
Which engine is it
Aeosome 😀😃 good luck
Man flip flops 😂 can't weld toes back on.
Boohoo pussy.
I was thinking the same thing but then remembered I've welded in crocs before aswell
@@robspear03 poopy green.
I've welded in basket ball shorts crocs and a wife beater with no gloves but you shouldn't
Рама хлипкая, развалится на первой кочке. Передаточное отношение слишком мало. Нужно хотя бы 9 к 1 (900 об мотора =100 об колеса). Сцепа буксует
Maybe late to the party but beautiful work 👌
Todos esta bien pero la cadena tiene que tener un protector, asi es muy peligroso, la cadena se puende soltar como tambien romper. 👍
nice vid hopefully you need to put a reinforcement steel bar on the side of the motor in addition more improvising for the ped itself.
ride safe out there!
and by nice motor you have ❤
The single plate needs more reinforcement to be a robust design. Currently, there is too much flexing and bending and welds be breaking at the bottom frame rails.
You might want a smaller sprocket for more top speed
Whats the top speed limit?
So simple and good job
Quantoes lvatra
Happy to subscribe.❤
Super!
I wonder if this motor will work on a wheel chair
если не ошибаюсь, то при такой передаче и оборотах в среднем 4500 в минуту....скорость самоката будет около 60-70 км час или буксовать сцепление..поездишь недолго.. шестерня напрямую....значит средние обороты 4500 минимум... это в минуту.. умножим обороты на 60 минут в часе...разделим передаточное на 3, приблизительно... возьмем 10 дюймовое колесо где-то 0,75 метра на оборот... итого 4500*60=270000 затем делим на 3 =90000 умножаем на длину 0,75 и делим на тысячу =67,5 средняя скорость...ну как то не реально....точнее немыслимо...плюс подшипник быстро выйдет из строя
Top, Cool.
Dang!thats gonna be awfully high geared!For a little motor,I would use as small of a sprocket on the clutch as I could find,like 10 or 11 tooth,so it will have good takeoff.(shoes and a rear brake would be advised...just sayin')
я с вами согласен. без тормозов это до первого переулка....
Exelent video brother
hello! cool idea! Can you tell me how to put a gearbox on a bike? Thanks.
62 CC and you got this thing to run at a brisk walking speed, that's downright hilarious