Been watching your videos and thanks for sharing it helps me a lot understanding more. , I'm from South Africa and expanding my Key Promming business with ECU cloning as well. Looking at buying the Foxflash as well. Can you recommend a good HEX DECODER EDITOR available for VIN editing ?
Thank you, I’m really glad to hear that my videos are helping you! It’s great to see your key programming business expanding into ECU cloning. For VIN editing, I’d recommend looking into tools like WinOLS or ECU Flash. They both have good reputations in the community for hex editing
When cloning (I have hexprog2). I cloned a sim2k-240 and vehicle starts find BUT the prndl is incorrect as is. Drive on dash, only lights when the shifter is in park. And park only displays and vehicle will start when shifter is in drive. The shifter is backwards. My question is is the sim2k-240 the only part number I need to worry about ? What other numbers will confirm matching between OG and new pcm. Also everything works normally with OG PCM installed
Thanks for the video. Will the car start if eeprom checksum is not corrected in writing? I am cloning one with kt200 but I have an eeprom chk correction problem. Can I only write without correction.
Question..If I copy/flash from old Ecu eprom where are stroge vin number and put in new/replecmant /donor Ecu eprom it will car start?Or I must copy/clone ALL Ecu Data to new/donor Ecu that can start engine?Soory im new one and I learning
Can this be done with an Autel IM608 with Xp400pro? I have red both pin numbers and I was hoping I could reset the ECM so it could be coded. But it says it is locked. Can I swap Eeprom data? Or can it only be done by flashing the whole ECM on the bench?
I AM FOR NOW ,,,,,,,,,JUST CONCENTRATING ON FINDING CAN PROBLEMS. I WILL HAVE TO GET INTO THIS WORK SOON THANKS FOR THE GREAT VIDEOS !!!!!!
Appreciate you and the team.
Thanks for your work brother !!!
Thanks for your work❤
Nice video I would like to do that on a landrover evoque I need some guidance
Thank you
I am a newbie I also have a foxflash
Great video! Thank you!
Been watching your videos and thanks for sharing it helps me a lot understanding more. , I'm from South Africa and expanding my Key Promming business with ECU cloning as well. Looking at buying the Foxflash as well. Can you recommend a good HEX DECODER EDITOR available for VIN editing ?
Thank you, I’m really glad to hear that my videos are helping you! It’s great to see your key programming business expanding into ECU cloning. For VIN editing, I’d recommend looking into tools like WinOLS or ECU Flash. They both have good reputations in the community for hex editing
Do you have a video where you show how to make the connections?
When cloning (I have hexprog2). I cloned a sim2k-240 and vehicle starts find BUT the prndl is incorrect as is. Drive on dash, only lights when the shifter is in park. And park only displays and vehicle will start when shifter is in drive. The shifter is backwards. My question is is the sim2k-240 the only part number I need to worry about ? What other numbers will confirm matching between OG and new pcm. Also everything works normally with OG PCM installed
How did you find the correct schematic for the chipset?
Thanks for the video. Will the car start if eeprom checksum is not corrected in writing? I am cloning one with kt200 but I have an eeprom chk correction problem. Can I only write without correction.
Correction is necessary if changes were made to the dumps.
Can you use this tool to clone a sim2k 250?
Kia Boyz 🪛🚗💨
The password you mention in this video the same password (6 digits) to neutralize, teach,etc vehicle security ? or its tricore (chip) password only ?
Tricore
Question..If I copy/flash from old Ecu eprom where are stroge vin number and put in new/replecmant /donor Ecu eprom it will car start?Or I must copy/clone ALL Ecu Data to new/donor Ecu that can start engine?Soory im new one and I learning
Copy everything
@@globalcommerce7654 but why i need pin code then?
Can this be done with an Autel IM608 with Xp400pro?
I have red both pin numbers and I was hoping I could reset the ECM so it could be coded. But it says it is locked.
Can I swap Eeprom data? Or can it only be done by flashing the whole ECM on the bench?
08 Sonata
On this ecm there's also vehicle data in the flash so the entire thing must be copied over, what model pcm are you working on?
@globalcommerce7654 it's a SIM2K-141 in a 2008 Hyundai Sonata
Do you have a websites or contacts you could clone an Ecu for me?
Yes, globalcommerceca.com
Contact me to flash my Sorrento ecm