Я прочитал много комментариев и вижу, что задаются одни и те же вопросы. Итак, я попробую объяснить, что есть в сборке и почему. Это спиртовая печь. Как заявляли другие, можно использовать и другие виды топлива. Во время сборки примерно на 3:14 вы увидите, как он просверлит 3 маленьких отверстия. Эти отверстия, которые он сверлит, являются форсунками пламени. Похоже, он сверлит эти отверстия сверлом диаметром 1 мм. Что, если вы посмотрите позже, примерно в 9:20, первое горение нехорошее, струи слишком маленькие. Затем где-то в 10:20 кажется, что он увеличил размер жиклеров до 3 мм. Посмотрите внимательно на пламя, оно действительно кажется больше. Теперь многие спрашивают, зачем использовать веревку? Веревка используется как фитиль, чтобы втягивать топливо в трубу и предварительно нагревать его. Этот предварительный нагрев топлива в фитиле запускает испарение жидкого топлива. Испарение жидкости происходит при нагревании жидкости до температуры кипения. Это также повышает температуру жидкого топлива в баке. Это повышает давление в баке, вызывая испарение большего количества топлива. Повышение давления вызывает струйный эффект. Вы хотите сжигать только пар, а не жидкое топливо. Надеюсь, это поможет кому-нибудь понять эту замечательную маленькую печь. Я надеюсь, что это хорошо переводится.
You can't go wrong when you use JB weld and they have different types of adhesive some may be more or less resistant to heat it depends on what type of epoxy you need to do the job 👍👍👍👍👍
Have you tried using a silica wick in those? Im guessing regular wicks will get charred after some use. Silica wicks dont burn... They dont wick as good as cotton (at least for ecig juice), but its still pretty absorbant, and im guessing it would wick good enough for transporting alcohol pretty efficiently...
beware, glue copper coil will eventually explode. just had my explode on me, lucky no one was burned. Creator like such video need to at least warn viewer.
Saludos desd mi colombia , felicitaciones sera q c pued hacer con los tarros mas grandes , lo otro y en otra clac d material ejem: en cobre , acero y en lugar d s cemento en sus respectiva soldadura y gracias x la atencion prestada y q mi DIOS los bendiga.
Great video, and you can stand your pot on the coils too. One question: what is the purpose of the wick? Will the heat burn the wick? Will the stove heat and boil the fuel without the wick?
so the wick essentially makes the propellant creep up it, getting it into the copper tube, which is then heated up from the fire, at that point it heats it up to gas state and has pressure forcing it out the 3 small holes causing the jet flame.
My guess is there are NO holes in the tubing... The way ANY alcohol stove works is that the alcohol heats up (creating an increase in vapors), which then pressurizes the stove, forcing the vapors out the jets which are then burned by the flames... In most stoves, there is no direct heat being applied to the alcohol but there's enough radiant heat there to still cause expansion... In the case of THIS stove, the wick (inside the tubes) draws fuel up into the tubes, which is then SUPER-heated by the flames, hyper-expands the vapors and forces them back into the stove, which, in turn forces the vapors out of the jets at a greatly increased rate, giving it that "jet" sound.... A couple of problems I see with this design is (1) The increased pressure / heat generated by this design is going to exceed the JB Weld (glue) specs and probably fail very quickly... (2) The jet holes seem to be too small for the amount of pressure being forced through them which is right on the verge of blowing out the flames... I would either make the holes twice as big OR put 2 holes under each tube... Overall it's a good design (in theory), but that glue is going to fail and possibly be a dangerous situation... JB Weld is fine for use in stoves where there's no direct heat being applied to glued areas but this stove is purposely heating the copper which is only being held in place by glue... Be careful with that
You got it right John B, l would also question weather the JB weld would hold for any length of time under that heat, quick set 5 min. good for 230 deg. reg. JB high strength 24 hr set time 550 deg. l use a lot of JB great stuff.
I like this explanation but I still can't understand how the tubes create vapor that pressurizes the can AND draws fuel up the wick. Doesn't the rush of vapor out the tubes prevent fuel from being drawn up?
Really really nice!! Congrats my brother! I really want to make something like this now! Haha But I have to ask, how we "turn off" it? I need to wait it burn the whole alcohol inside it? If i just "kill the flame" doesn't will still letting the gas goes out of it? If there were some way to close the thin hole that let the gas out can it work to "turn off" the stove? Anyway, congrats for the nice project you have done!
I have read through many of the comments and see the same questions asked. So, I will try and explain what is in the build and why. This is an alcohol stove. They are using alcohol. As others have stated, other types of fuel can be used. During the build at about 3:14 you will see him drill 3 small holes. These holes he is drilling are the jets for the flame. Looks like he is drilling these holes with a 1mm bit. Which if you watch later, at about 9:20 the first burn is not good, jets are to small. Then at about 10:20 it looks like he has increased the size of the jets to 3mm. Look closely at the flame it does look bigger. Now, many have asked why use the rope? The rope is used as a wick, to pull fuel up into the pipe and pre-heat it. This pre-heating of the fuel in the wick starts a vaporization of the liquid fuel. Vaporization of a liquid occurs when a liquid is heated to its boiling point. This also raises the temperature of the liquid fuel in the tank. Which raises the pressure in the tank, causing more fuel to vaporize. The rise in pressure causes the jet effect. You want to burn only the vapor not the liquid fuel. Hope this helps someone out there understand this great little stove.
Good job... Please When you insert the small pease in the top large one... are you shuted it by soldering or by devicon or just close it titly... Warm regards
Ya entendí el funcionamiento, al calentarse los tubos de cobre con las mechas húmedas de alcohol se gasifica y aumenta la presión y sale expulsado por las tres perforaciones minúsculas de 0,6 mm. Excelente vídeo, felicitaciones y saludos cordiales desde Quito Ecuador.
Hd hd3 does that copper tubing has little tiny holes for the alcohol to jet spray? There will be no fire whatsover if theres no flamable outlet would it?
Temperature rating of normal JB Weld is listed as 500F continuous, 600F for 10 minutes. I'd be willing to bet those copper loops are getting up pretty close to that!
@@aleehene Probably, I wouldn't be surprised to find it gives off toxic fumes when heated too. I would personally use silver solder or fire cement, though I doubt solder would bond to aluminium cans
Good idea, but as said below the JB weld could fail, it needs tested to destruction. I use a trangia stove with my M-kettle, works great, but I think I'll make one of these to suit, the boil time is much quicker by a good 3 mins.
its a pressure type stove. The three coils act as a heating element. As temperature increases, pressure builds up which results into pressurized ejection of alcohol. Its efficiency is increased because of the small diameter of the holes (the small ones in between the coil). If you check out "how to make Fancy Feast stoves", they'll explain why you have to make a pressure hole. That being said, since its just a stand alone experiment/demo, you'll have to make one (if you're bored) to compare boiling times with other types of alcohol stove.
@@beeeean I can't say much about it since I haven't made one but here's my take: Its effecient despite the hassle of the assembly required. It took this stove 5mins to boil water while it roughly takes 6mins to boil. Its worth the build as long as you have junk lying around. The U shaped copper coil is, what I think, the hardest part to look for. The only thing I know that has a U shaped copper coil is the refrigerator. This stove needs a cook stand that also acts as a wind barrier. Just like the one used in the video. If you put your pot on the coil, it could risk damaging the burner. This could be used as a secondary stove for boiling noodles and water. If you want to do quick fry, I think you'd have to increase the fuel capacity. The main drawback for this,IMO, is refueling between uses. You would wait for the burner to be cool to the touch to refuel or risk hurting yourself.
Meu caro IRIS, por acaso vc não conhece algum Japonês ou brasileiro que conheça Língua Japonesa!?! Nos caninhos de Cobre não tem nenhum Furo; vc também pode utilizar caninhos de Alumínio. > O furinho está na BASE(no meio + -) de onde foram encaixados os tubos de cobre. WhatsApp+5511-9-9134-9944; São Paulo, SP - Zona Leste(Penha).
Я прочитал много комментариев и вижу, что задаются одни и те же вопросы. Итак, я попробую объяснить, что есть в сборке и почему. Это спиртовая печь. Как заявляли другие, можно использовать и другие виды топлива. Во время сборки примерно на 3:14 вы увидите, как он просверлит 3 маленьких отверстия. Эти отверстия, которые он сверлит, являются форсунками пламени. Похоже, он сверлит эти отверстия сверлом диаметром 1 мм. Что, если вы посмотрите позже, примерно в 9:20, первое горение нехорошее, струи слишком маленькие. Затем где-то в 10:20 кажется, что он увеличил размер жиклеров до 3 мм. Посмотрите внимательно на пламя, оно действительно кажется больше. Теперь многие спрашивают, зачем использовать веревку? Веревка используется как фитиль, чтобы втягивать топливо в трубу и предварительно нагревать его. Этот предварительный нагрев топлива в фитиле запускает испарение жидкого топлива. Испарение жидкости происходит при нагревании жидкости до температуры кипения. Это также повышает температуру жидкого топлива в баке. Это повышает давление в баке, вызывая испарение большего количества топлива. Повышение давления вызывает струйный эффект. Вы хотите сжигать только пар, а не жидкое топливо. Надеюсь, это поможет кому-нибудь понять эту замечательную маленькую печь. Я надеюсь, что это хорошо переводится.
Japanese are excellent at taking an idea and making it great ...Wow well done I've never seen anything like this ...Amazing!!!
He is Indian
The fact that you got this to behave like a kerosene pump stove off just alcohol is impressive, very good design friend keep tweeking it to perfection
This is cool, very clever! BTW I love how the cat stops by periodically to check on the project.
Great idea👍
so gonna have to try making one of these. THANKS VERY MUCH for showing me how. Great work n keep it up
High, a very interesting construction with the tubes. Kindly Fiete
Good 'ol JB weld. I've used it on several alcohol stoves on fittings. Works great!
THANKS FOR WATCHING
超かっこいいですね！！
欲しいです…
Muito bom!
Vou fazer e ver se dá certo e depois farei em escala maior.
面白い！コッパーの代わりにアルミパイプを使ってもいいですかね？
Nice share video ..awsm 📱👍
You can't go wrong when you use JB weld and they have different types of adhesive some may be more or less resistant to heat it depends on what type of epoxy you need to do the job 👍👍👍👍👍
Great concept.... I love it.
Have you tried using a silica wick in those? Im guessing regular wicks will get charred after some use. Silica wicks dont burn... They dont wick as good as cotton (at least for ecig juice), but its still pretty absorbant, and im guessing it would wick good enough for transporting alcohol pretty efficiently...
muito bom...alias exelente ... obrigado 🇧🇷🇧🇷🇧🇷
good. thanks for your video. It's very helpful
Terima kasih dari Indonesia !
Exelente una gran creatividad felicitaciones muy bien
Mnogo ti hvala! Dobra idea! Thank you! Good idea!
THANKS FOR WATCHING
How long can you use the burner in one application for given cc of Alcohol?
Hi, it works with oil diesel or gas too?
Olá, ele funciona com óleo diesel ou gasolina também?
Excelente Gracias
excellent video ...thanks
I like it great idea for tiny hole for most power full fire just like a gas stove burn
ダディハートさん
何時も興味を持って拝見させて頂いてます。
動画を拝見していて、アルコールストーブを作って見たくなりました。
色々作られてますが、（Jet stove Coil Alcohol Stoveアルコールストーブ超強力HD型）
や同じ同管を使ったWコイル型・同管をアーチ状に3ケ配置して缶に穴を開けるタイプ等
ありますが、強力なタイプはどれに成りますか？
後もう一点、火力調整が出来ないと思いますが複数個作成して入れ替えるしかないですよね？ あの接着剤は私もバイクの整備などで使用しています。
熱には強いんですね！？
最近、年甲斐もなくディオにJF06エンジンのリーディオ作りました。
KOSO30キャブと排気ポート加工＋リア12インチでかなりスピード伸びます。
beware, glue copper coil will eventually explode. just had my explode on me, lucky no one was burned. Creator like such video need to at least warn viewer.
I was going to make a few, but something didn't seem right. All that fire with 3 little holes. Potential explosion is what I saw.
I had one explode too haha
This is so cool. I have so many questions, though. wish the captions were in English.
x2
This is a pretty efficeint stove about 5 minutes boil...not bad.
Good job. 4 tubes would be perfect for me.
THANKS FOR WATCHING
Saludos desd mi colombia , felicitaciones sera q c pued hacer con los tarros mas grandes , lo otro y en otra clac d material ejem: en cobre , acero y en lugar d s cemento en sus respectiva soldadura y gracias x la atencion prestada y q mi DIOS los bendiga.
Congratulations man
thanks
Great video, and you can stand your pot on the coils too. One question: what is the purpose of the wick? Will the heat burn the wick? Will the stove heat and boil the fuel without the wick?
so the wick essentially makes the propellant creep up it, getting it into the copper tube, which is then heated up from the fire, at that point it heats it up to gas state and has pressure forcing it out the 3 small holes causing the jet flame.
Bagus banget bro..? ide kreatifx..👍 ini buat contoh untuk kita semua..supaya kita terdorong untuk menciptakan sesuatu yang bermanfaat..amin.
THANKS FOR WATCHING
My guess is there are NO holes in the tubing... The way ANY alcohol stove works is that the alcohol heats up (creating an increase in vapors), which then pressurizes the stove, forcing the vapors out the jets which are then burned by the flames... In most stoves, there is no direct heat being applied to the alcohol but there's enough radiant heat there to still cause expansion... In the case of THIS stove, the wick (inside the tubes) draws fuel up into the tubes, which is then SUPER-heated by the flames, hyper-expands the vapors and forces them back into the stove, which, in turn forces the vapors out of the jets at a greatly increased rate, giving it that "jet" sound.... A couple of problems I see with this design is (1) The increased pressure / heat generated by this design is going to exceed the JB Weld (glue) specs and probably fail very quickly... (2) The jet holes seem to be too small for the amount of pressure being forced through them which is right on the verge of blowing out the flames... I would either make the holes twice as big OR put 2 holes under each tube... Overall it's a good design (in theory), but that glue is going to fail and possibly be a dangerous situation... JB Weld is fine for use in stoves where there's no direct heat being applied to glued areas but this stove is purposely heating the copper which is only being held in place by glue... Be careful with that
Absolutely. You need to solder or braze the tubes on.
You got it right John B, l would also question weather the JB weld would hold for any length of time under that heat, quick set 5 min. good for 230 deg. reg. JB high strength 24 hr set time 550 deg. l use a lot of JB great stuff.
And also the wick will burn and turn to carbon.
I like this explanation but I still can't understand how the tubes create vapor that pressurizes the can AND draws fuel up the wick. Doesn't the rush of vapor out the tubes prevent fuel from being drawn up?
Super idea
Very cool. What is the purpose of the little holes beside the main filler hole? Improves adhesion of the JB to the nut?
grip?
Yes.......alway use small holes when you use jb weld.....acts as an anchor
He could also just scratch the can to create a better grip between the adhesive and the surface
Muito criativo aliás altamente engenharia alto padrão
This material inside the coils do not get burned inside? It must pass al the way through in a single piece?
Really really nice!! Congrats my brother!
I really want to make something like this now! Haha
But I have to ask, how we "turn off" it? I need to wait it burn the whole alcohol inside it? If i just "kill the flame" doesn't will still letting the gas goes out of it? If there were some way to close the thin hole that let the gas out can it work to "turn off" the stove?
Anyway, congrats for the nice project you have done!
（＾＾）
感謝
You have a creative brain
（＾＾）
Excelente pa el Café y la Maruchan o ramen
Excelente trabajó
you are so smaaaaart 😉😊
Wow! How many time on the fire?
does the copper tubing have tiny holes under the arch ?
Wow! Very good
こんにちは
各種パーツの熱の影響はどうですか？
パイプ内の麻と接着剤は2液タイプをしようとのことですが
これだけ圧がかかり高温になると破損が怖そうです。
Sounds just like a torch
Very nice build! 🤟😎
THANKS FOR WATCHING
c'est quoi cette merveille. bravo j'adore
THANKS FOR WATCHING
thank you
Awesome!
PARABÉNS BRASIL RIO DE JANEIRO
I have read through many of the comments and see the same questions asked. So, I will try and explain what is in the build and why. This is an alcohol stove. They are using alcohol. As others have stated, other types of fuel can be used. During the build at about 3:14 you will see him drill 3 small holes. These holes he is drilling are the jets for the flame. Looks like he is drilling these holes with a 1mm bit. Which if you watch later, at about 9:20 the first burn is not good, jets are to small. Then at about 10:20 it looks like he has increased the size of the jets to 3mm. Look closely at the flame it does look bigger. Now, many have asked why use the rope? The rope is used as a wick, to pull fuel up into the pipe and pre-heat it. This pre-heating of the fuel in the wick starts a vaporization of the liquid fuel. Vaporization of a liquid occurs when a liquid is heated to its boiling point. This also raises the temperature of the liquid fuel in the tank. Which raises the pressure in the tank, causing more fuel to vaporize. The rise in pressure causes the jet effect. You want to burn only the vapor not the liquid fuel. Hope this helps someone out there understand this great little stove.
The cooper tube is drilled?
Thanks a lot
Very nice
Отличная работа.
Good job... Please When you insert the small pease in the top large one... are you shuted it by soldering or by devicon or just close it titly... Warm regards
Ficou..Muito bom..Mas está música ficou ruim de mais..kkkkkkkkk
Excellent!
Ya entendí el funcionamiento, al calentarse los tubos de cobre con las mechas húmedas de alcohol se gasifica y aumenta la presión y sale expulsado por las tres perforaciones minúsculas de 0,6 mm. Excelente vídeo, felicitaciones y saludos cordiales desde Quito Ecuador.
コメントありがとうございます
No es q se caliente el tubo de cobre es el alcohol el q prende fuego
Es así de simple amigo
すごい
Hd hd3 does that copper tubing has little tiny holes for the alcohol to jet spray?
There will be no fire whatsover if theres no flamable outlet would it?
dude watch and learn...damn or read some comments... about 5 other ppl have asked.
Witch size of drill bit you use for the jet ?
Dizel ile çalışır mı? Nasıl söndürebiliyoruz?
Nicely done, though I would use heat resistant stove sealant/fire cement instead of JB weld ;)
THANKS FOR WATCHING
Temperature rating of normal JB Weld is listed as 500F continuous, 600F for 10 minutes. I'd be willing to bet those copper loops are getting up pretty close to that!
@@aleehene Probably, I wouldn't be surprised to find it gives off toxic fumes when heated too. I would personally use silver solder or fire cement, though I doubt solder would bond to aluminium cans
オートウエルドはどこに売っていますか？
Thanks
Great!
Congratulations
Saka moko
ダディーハートさんは色々な銅管コイル型ストーブを制作してお見えですが、どの型が一番火力が強いでしょうか？宜しければお教えください。
こんばんは（＾＾）
どの作り方をしても銅管を太くすると火力が増します
でも５ｍｍ以下で作った方がいいです
火力が増すとアルミ缶だと持たないことがありますから
この動画の銅管は４ｍｍを使用してます。
Great
For How long does It burn ??? 🤔....
Nice
i think this way less alcohol will be used with thes ame outcome
你好，你好嗎？我是從哥倫比亞麥德林給你寫信，是提前問一下你的爐子上用的是什麼膠水，非常感謝
Muito bom, parabéns
THANKS FOR WATCHING
I like this build but a English translation would be nice
Good idea, but as said below the JB weld could fail, it needs tested to destruction.
I use a trangia stove with my M-kettle, works great, but I think I'll make one of these to suit, the boil time is much quicker by a good 3 mins.
Very Nice!!! Kotira Airuton fron burajiru
Muy bueno
عاشت يدك يا بطل
would be awesome to see this and have english audio
Awesome
Great video..thank you for sharing ...but for 5 minute how many CC alcohol do you need? Thank u👍👍👍
Wish this had english translation or english version of this. Curious how it works exactly
its a pressure type stove. The three coils act as a heating element. As temperature increases, pressure builds up which results into pressurized ejection of alcohol. Its efficiency is increased because of the small diameter of the holes (the small ones in between the coil). If you check out "how to make Fancy Feast stoves", they'll explain why you have to make a pressure hole.
That being said, since its just a stand alone experiment/demo, you'll have to make one (if you're bored) to compare boiling times with other types of alcohol stove.
@@buki7474 Hmm do you think this works as a camping stove? With wind and all
@@beeeean I can't say much about it since I haven't made one but here's my take:
Its effecient despite the hassle of the assembly required. It took this stove 5mins to boil water while it roughly takes 6mins to boil.
Its worth the build as long as you have junk lying around. The U shaped copper coil is, what I think, the hardest part to look for. The only thing I know that has a U shaped copper coil is the refrigerator.
This stove needs a cook stand that also acts as a wind barrier. Just like the one used in the video. If you put your pot on the coil, it could risk damaging the burner.
This could be used as a secondary stove for boiling noodles and water. If you want to do quick fry, I think you'd have to increase the fuel capacity.
The main drawback for this,IMO, is refueling between uses. You would wait for the burner to be cool to the touch to refuel or risk hurting yourself.
hola, muy bonito y practico
THANKS FOR WATCHING
The holes drilled in the bottom of the tubing?
meu amigo caninho de aluiminio também serve.
THANKS FOR WATCHING
show...show. ..show. ....obrigado
Не выёбывайся.
Are those small holes where the gas will be expelled? can someone answer me please
Sim, os três furos é por onde sairá o vapor do álcool quando aquecido.
Genial 👍 😁
THANKS FOR WATCHING
بسیار عالی متشکرم👍👏
Cuánto tiempo dura encendido?
✓Amazing 👍 *Greeting from Indonesia ❤️🇮🇩❤️
Vc fez algum furos nos tubos de cobre para queimar o álcool ou por onde sai o vapor????
Meu caro IRIS, por acaso vc não conhece algum Japonês ou brasileiro que conheça Língua Japonesa!?!
Nos caninhos de Cobre não tem nenhum Furo; vc também pode utilizar caninhos de Alumínio.
> O furinho está na BASE(no meio + -) de onde foram encaixados os tubos de cobre.
WhatsApp+5511-9-9134-9944; São Paulo, SP - Zona Leste(Penha).
Pelo micro furos da lata.
このバーナーの銅パイプを真鍮にしたら耐久性は落ちますかね？
こんばんは（＾＾）
どうなんでしょうね？
真鍮のが耐久性あると思いますよ
銅管は火の熱で赤くなりますし
そうなると銅はとても柔らかくなりますから
まぁ、試したことないですけど。