Hello Sergey, in the video we have explained the general process, of course, during the fabrication time, we will cut the elbows at the indicated degrees using the level and meter and make turns in the spool. We will make like videos on next weeks
@@Piping-engineer Hello, thank you for the answer. I also have a question. It means that I can obtain the actual length of the pipes using the SolidWorks program instead of using your method for calculating the length of the pipes. In short, the SolidWorks program is effective or what?
Thanks for watching and comments.We have many videos for calculation pipe length, my friend. please see below links videos: th-cam.com/video/msctTnSZ8SI/w-d-xo.html th-cam.com/video/msctTnSZ8SI/w-d-xo.html th-cam.com/video/0aBkOajy-AM/w-d-xo.html th-cam.com/video/XryP3LY-1Us/w-d-xo.html th-cam.com/video/4z-IPYv1AWA/w-d-xo.html
Very naiys vidio
Very good calculation
Please more descriptions sharing
bravo ,good channel
Super video
Very nice video
👍👍👍👍
🤗🤗🤗👍👍👍
Easy calculation video
So nice this lecture sir
Thank you for your work.
Thanks sir.... For this video..
Very nice you have convenced but do the practical
Long albwo center. Tan{90÷2}×1.5×3×25.4=114mm.albwo.center.hota.hai
Gaiprod 6mm.
Tan{90÷2}×1.5×3×25.4=114mm.albwo center.
114+114+6=234mm
400-234=166mm.pipe.ka.linght.hai
Weld neck flange PCD.
Tan{90÷2}×1.5×3×25.4=114
Weld neck flange. 65mm
Gaiprod. 6mm
114+65+6=185mm
200-185=15mm.pipe.ka.linght.hai
Thanks for watching
Could You please explain this in English
Hello master! How do you find degree of both elbows?
Hello Sergey,
in the video we have explained the general process, of course, during the fabrication time, we will cut the elbows at the indicated degrees using the level and meter and make turns in the spool. We will make like videos on next weeks
@@Piping-engineerhello. Please tell me the degree of both elbow. How do you calculate it, because its not 90 degree. Thanks
Bravo,good team
Very nice !
Many thanks
Super sir
I have a question: If a person can draw using the SolidWorks program and then measure these pipes, is this correct without these calculations ?
Reply me eftersom I use it.
I use Sketcup program
@@Piping-engineer Hello, thank you for the answer. I also have a question. It means that I can obtain the actual length of the pipes using the SolidWorks program instead of using your method for calculating the length of the pipes. In short, the SolidWorks program is effective or what?
Super!!!
Many thanks for comments
Why you don't explain how did you calculate this? It have no sense when you just put some numbers, then people just starts wondering why, from where
Thanks for watching and comments.We have many videos for calculation pipe length, my friend.
please see below links videos:
th-cam.com/video/msctTnSZ8SI/w-d-xo.html
th-cam.com/video/msctTnSZ8SI/w-d-xo.html
th-cam.com/video/0aBkOajy-AM/w-d-xo.html
th-cam.com/video/XryP3LY-1Us/w-d-xo.html
th-cam.com/video/4z-IPYv1AWA/w-d-xo.html
Türkce
Зачем описание делать на русском...
Many thanks for watching and comments. Russian subtitles were added
@@Piping-engineer tanks)