I done everYthing Like you in the Video 100% and nothing happened. I set Limiter to 6700 and hysteris Like you. You Know Why? I deactivAted ews too. Thanks. And Good Tutorial by the way 💪🏻
Great Video!!! Could you please the link or the .xml file for the E36 ms41 ecu definitions. I've searched everywhere and I just can't seem to get the correct file. Thanks in advance
Hey can you make a video how to bridge the 20 pin connector with switch or can you tell me who's selling a connector like that. Im frustrated to properly bridging those connectors:(
Привет! По акценту слышу, что ты наш парень. Лачик 1.4, как ты уже понял стоковая отсечка совсем не звучит. Подскажи пожалуйста где искать нужную прошивку? Как ее залить я уже смотрел и даже необходимое оборудование для этого купил. Дело в том, что проживаю в Европе, катик и ЕГР на месте ибо с этим тут строго, евро 2 залить не получится. Возможно есть вариант покопаться в залитой прошивке и просто подкорректировать тайминги срабатывания отсечки вместо того, что бы заливать новую (неизвестную) прошивку? Я в этом пока, что очень мало понимаю, поэтому буду очень сильно благодарен за вразумительный ответ. Спасибо большое!
Hi i have got a rpm limiter at 5200-5400 грт. I think it's a kind of a limp mode on my e34 525 1990 m50b25 non vanos engine Bosh ecu. That type of limp mode is mostly caused by a broken or bad working abs/speed sensor. Is it possible to cheat the rev limiter?
I m following every step you are doing and everytime im facing the same problem in romraider logger which is " unable to send ecu init" and ihave been following all the steps in the romraider fourm - why we have to connect pin 14 to pin18
Здравей , подобрява ли нещо като поведения на колата или е просто за кеф да е по бърз. Знам че дават макс К.С. На 5500 оборота ? Пс. Евала за Инглиш контента и канала!
Hi, after flashing the ecu, i got crank no start situation and getting these codes 100 control unit self test failed 68 tank venting valve Fuel pump is working but it looks like there is no spark Any idea ? Thanks in advance
@@mershatamrat2282 thanks, I got it fixed a local shop reflashed my ic chip with old m52 code, it was not working properly but I revived the ecu with it and got it working again
hi crank!! i was looking my partial read on RR but on my (limiters) i only have vehicle speed limit, hard limiter and vss error. how can i see the hysteresis A/B like yours? thank you!!
I have the same issue but I only see Speed limit and hard limiter I do not see Vss error and im trying to change mine because like he says mine is limited to 5259 so just wondering were you ever able to figure it out ?
@@folst.3331 yess i did it!! You need to login first on RR web page and download the latest ms41 definitions.. add to the definitin manager and its done. i had a very old definitions version and that was all🤙🏼🤙🏼
@@wedepeixmen Do you by any chance have the Links Im using the ECU portal and I went thru the forums and I couln't find the link im sorry to bother you if you can help thank you and if not I appreciate the info
On MS 41.0 Vanos looks only for RPMs , on MS 41.2 you need VSS , but this signal is coming from the differential . And the wire that I'm talking about is from the instrument cluster to the ECU , so with or without it the Vanos is going to work
CRANK could you explain the benefits of ms41.0 to ms41.2 conversion if there is any? Cant seem to understand why so many people do it. Also can you do a video on how to have pop and bangs work on/off with the aircon switch. Thanks, youre videos are very helpful and save lots of time reading through the rom raider forums
@@crank3646 i blown up m52b28 2 weeks after set my revlimiter to 7000 and i had oil pump failure.Now swaped to new engine and welded oil pump star. Just saying, it can go south
I done everYthing Like you in the Video 100% and nothing happened. I set Limiter to 6700 and hysteris Like you. You Know Why? I deactivAted ews too.
Thanks. And Good Tutorial by the way 💪🏻
Great Video!!! Could you please the link or the .xml file for the E36 ms41 ecu definitions. I've searched everywhere and I just can't seem to get the correct file. Thanks in advance
Hey can you make a video how to bridge the 20 pin connector with switch or can you tell me who's selling a connector like that. Im frustrated to properly bridging those connectors:(
Здравей колега!
Имам няколко въпроса относно програмите които използваш.
Ще се радвам да може да се свържем!
П.с. следя редовно канала!
Hi. I want to idle the ms41. I want to increase to 70rpm. Can you describe it with video. Thanks
Hi! What is ‘Immediate’ and ‘Resume Delay’ ? Can u explain pls.
Thanks.
Привет! По акценту слышу, что ты наш парень. Лачик 1.4, как ты уже понял стоковая отсечка совсем не звучит. Подскажи пожалуйста где искать нужную прошивку? Как ее залить я уже смотрел и даже необходимое оборудование для этого купил. Дело в том, что проживаю в Европе, катик и ЕГР на месте ибо с этим тут строго, евро 2 залить не получится. Возможно есть вариант покопаться в залитой прошивке и просто подкорректировать тайминги срабатывания отсечки вместо того, что бы заливать новую (неизвестную) прошивку? Я в этом пока, что очень мало понимаю, поэтому буду очень сильно благодарен за вразумительный ответ. Спасибо большое!
What hardware ID does MS4X flash ask for when you initially set the program up to get the license generator?
Can you still get the fast rev limiter if you keep the rpm around 6500-6600 ?
Yes
running fast rev on 328 with 360KM at 7K RPM 😈
Nice video,good start of the day☀️👍
Thanks :)
Hello. can you tell me what i need to change in the map to get soft popcorn without fire from the exhaust? ms41 bmw e39 523i driver.
Hey budy im interested to make the same options to my m54b30 can you make a video or give me some advice how to do it ?
Адмирации за усилията да направиш толкова полезни видео материали! Наличен ли е за свободно сваляне софтуера?
Nice video man, thank you! Where can buy this cable and the program? Thanks
Hi i have got a rpm limiter at
5200-5400 грт.
I think it's a kind of a limp mode on my e34 525 1990 m50b25 non vanos engine Bosh ecu.
That type of limp mode is mostly caused by a broken or bad working abs/speed sensor.
Is it possible to cheat the rev limiter?
I m following every step you are doing and everytime im facing the same problem in romraider logger which is " unable to send ecu init" and ihave been following all the steps in the romraider fourm - why we have to connect pin 14 to pin18
Is this software suitable for this engine? M62B44 bmw 540i e39
Will this work on m52b25 ?
Thanks for all the videos !
Like a charm
Здравей , подобрява ли нещо като поведения на колата или е просто за кеф да е по бърз. Знам че дават макс К.С. На 5500 оборота ?
Пс. Евала за Инглиш контента и канала!
I have an M50 manifold on my m52b25 can I use the program u use to make adjustments to the map as IV lost power down low since M50 manifold mod
Hi, after flashing the ecu, i got crank no start situation and getting these codes
100 control unit self test failed
68 tank venting valve
Fuel pump is working but it looks like there is no spark
Any idea ?
Thanks in advance
Brick ecu
@@mershatamrat2282 thanks, I got it fixed a local shop reflashed my ic chip with old m52 code, it was not working properly but I revived the ecu with it and got it working again
Please show how to do pops and bangs on ms41
www.romraider.com/forum/viewtopic.php?f=58&t=11393&start=465 rekur te viss ir rakstīts un izdarīt elementāri
Sanāca pat šādi bet aizdegās zondas vads un uzliku parastu popkornu
instagram.com/p/CChHqF-DKpW/
When I remove the catalytic converters , probably will do :)
Hopefully we will see launch control soon from you as ive seen itdone but for some reason people removed the video
do you have the links to the cables please?
Thanks sir TH-cam training course
Where do i download ms41 definitions? Romraider is down.
Bro i have a question, can u program this on the orginal ecu or do u need a siemens ms41 ecu please help
Ms41 is the original ecu
can i increase rpm limit in automatic transmission m52b28?
Is it the same thing for ms42?
What difference read partial and read full?
Great video👌
@Vincent Duncan where the fuck did you find my comment on this sick e36
Do you have to have the bridge on the cable? I have a basic Inpa K+Dcan cable, no bridge switch, will it work?
For flashing the ECU you need a bridge
@@crank3646 Thank you for your replies! Looking to do this and the camshaft swap to my car too. Maybe M54 camshaft, hard to find S52 ones haha
@@anton6299 In my opinion the M54 camshaft upgrade is not worth it
@@crank3646 do you need to bridge pin 2 with pin 17 and pin 14 with pin 18 or just pin 14 with pin 18
THIS WORKS ON A M52B20?
Do you have map file for m50 intake ?
This very good
hi crank!! i was looking my partial read on RR but on my (limiters) i only have vehicle speed limit, hard limiter and vss error. how can i see the hysteresis A/B like yours? thank you!!
I have the same issue but I only see Speed limit and hard limiter I do not see Vss error and im trying to change mine because like he says mine is limited to 5259 so just wondering were you ever able to figure it out ?
@@folst.3331 yess i did it!! You need to login first on RR web page and download the latest ms41 definitions.. add to the definitin manager and its done. i had a very old definitions version and that was all🤙🏼🤙🏼
@@wedepeixmen Do you by any chance have the Links Im using the ECU portal and I went thru the forums and I couln't find the link im sorry to bother you if you can help thank you and if not I appreciate the info
@@wedepeixmen So I believe I found the definitions was it the 45.09 xml but I still don't see what I need any ideas ?
@@folst.3331 try removing from the RR local folder the car def and ecu def xml´s. and then add from RR the 45.09 definition. it worked for me
Интересно видео ще е да направиш 2step или burble tune☺️
Трябва да си премахна катализаторите преди това , че ще заминат за норматив
👍😎
What version of romraider you use?
Just use the latest version of rom raider and it should be fine
Does the ecu not need vss for vanos to work?
On MS 41.0 Vanos looks only for RPMs , on MS 41.2 you need VSS , but this signal is coming from the differential . And the wire that I'm talking about is from the instrument cluster to the ECU , so with or without it the Vanos is going to work
CRANK could you explain the benefits of ms41.0 to ms41.2 conversion if there is any? Cant seem to understand why so many people do it. Also can you do a video on how to have pop and bangs work on/off with the aircon switch. Thanks, youre videos are very helpful and save lots of time reading through the rom raider forums
Hello my frend ,how are you ?
Hy can you give me a link for the definition files. In my definition files I have only the rev limiter, no hysteria
i have the same probleme right now did you found a solution ?
drive.google.com/file/d/10lDUjm8u7j30V8XcB_18FHvlfXHuzjss/view FOUND !
very nice video, thanks
So glad I'm the 666 thumbs up.
What a devil
Направи същия клип самоче по български език
👍
Мотора двоен ванос ли е ?
Не единичен
CRANK а с мс43 как може да ттане това ? Понеже съм с м54б30
@@BGDHP В romraider форума има достатъчно информация за това
Можели помощ.Оборотите ми играят на M50B20 1991
7k is to much,stock oil pump will get loose and you will blow engine
This is not M54 3.0L , so doubt I will have problems with that :)
@@crank3646 i blown up m52b28 2 weeks after set my revlimiter to 7000 and i had oil pump failure.Now swaped to new engine and welded oil pump star. Just saying, it can go south
@@jahamuha2 I have done this to several cars and they see a lot of abuse . Still no failure . But everything is possible
@@crank3646 ihave 7200rpm lol
Yes, IF you use wrong, or dirty oils and oil changes is too long. My m52 is driven about 400 thousand kilometres and oil pump is working still fine.
Brat izmori me da te slusham 🤣
😪💔
По русски базарь!
Hello bro how are you can I email you I have question about bmw's tool