Start at 2:23 finish at 2:50. If that was me, start swearing at 2:23, work ongoing and more swearing at 2:50. 4:25 work completed still swearing. 5:45 boat in driveway, swearing still at a level 8. 7:45 , neighbors peeking out windows swearing down to level 4 sustained with gust of level 7 as gear is packed back into the garage. 9:15 lights out swearing has subsided to light level 1, dog has come out of hiding, wife goes to bed with disgusted look back over her shoulder. Cooler is now empty, cans in the yard around boat and trailer. Great content and very helpful. If i wind up in this situation at least I know what has to be done. Still going to have a cussing fit but maybe not so bad.
Ty for sharing your knowledge with us! My favorite channel! If you had to replace your trolling motor because it burned up, what size, type, brand would you buy again for gigging?
Thank you for choosing Arby’s. 😂😂😂😂. I have 3 things in my pocket at all times. Knife,nail clippers and a small sharpening stone. If you would have had to. You could always find a rock to knock off a bur. Keep on keeping on brother. God Bless my friend. 😎
Couple of questions 😎 where did you buy those pre packed hubs? I have only replaced mine one time, bought the parts at NAPA & they didn’t have pre packed, could have been out though ,, What tells you when you need to replace the springs ? Another great video 😎
Got to do one tomorrow
quarts rocks all over alamama make great files in a tight!
I always put my tire back on before tightening the center bearing so I can use it to get the slack out exact then put my Carter key in .
The stuff you go through to make a video. Thanks for sharing.
lol, thanks brother!
CorrosionX do a wheel bearing grease. Sounds like you do a lot of trailer miles, it might make for an interesting product test.
A dual axle trailer jack is awesome, dont need to lug around a big plastic car ramp
I knew you was going to say that. thank you for choosing Arby’s.😂
Lol, I couldn't resist!
Start at 2:23 finish at 2:50. If that was me, start swearing at 2:23, work ongoing and more swearing at 2:50. 4:25 work completed still swearing. 5:45 boat in driveway, swearing still at a level 8. 7:45 , neighbors peeking out windows swearing down to level 4 sustained with gust of level 7 as gear is packed back into the garage. 9:15 lights out swearing has subsided to light level 1, dog has come out of hiding, wife goes to bed with disgusted look back over her shoulder. Cooler is now empty, cans in the yard around boat and trailer.
Great content and very helpful. If i wind up in this situation at least I know what has to be done. Still going to have a cussing fit but maybe not so bad.
Lol, good stuff brother! Thanks for the cleaver comment!
I would be the one who kept 4 spares. Cause that would be my luck LOL
Lol, me too!
Ty for sharing your knowledge with us! My favorite channel! If you had to replace your trolling motor because it burned up, what size, type, brand would you buy again for gigging?
Thank you brother! Minn Kota 112's tillers are tough as nails! I have thousands of hours on mine!
It may be the camera angle, but it looks like the rear axial shifted backward on the leaf springs.
GoPro distortion, axle is good.
Watchin' n scribin'.
Thanks brother!
Thank you for choosing Arby’s. 😂😂😂😂. I have 3 things in my pocket at all times. Knife,nail clippers and a small sharpening stone. If you would have had to. You could always find a rock to knock off a bur. Keep on keeping on brother. God Bless my friend. 😎
Lol!
Great tip capt. Always be prepared!!
Couple of questions 😎 where did you buy those pre packed hubs? I have only replaced mine one time, bought the parts at NAPA & they didn’t have pre packed, could have been out though ,,
What tells you when you need to replace the springs ?
Another great video 😎
I get my hubs locally from Northern Tool in Mobile. Springs about 2-3 years, it want be long. Thanks for commenting!
You working on bearings. I’ve seen that before 😂😂
Lol, once or twice brother!
How long did it take you to