Wow, this video was an absolute game-changer for me! I've been tirelessly searching through countless courses for hours, I truly felt stuck and overwhelmed as a beginner. This video covered everything I needed to know, and it made me feel like a happy kid again :DDDD Also, the way you divided this video into parts is incredibly helpful Thank youuu so much Robert!!
Thank you, i usually select the component and use the command "Align to the Grid". One tip, in the panel "PCB Rules and Violations" you can run directly only one rule by selecting it, right click "Run DRC Rule Class(..).".
I have just also looked the wohle pcb form this schematic. I noticed that there are differential pair Con-USB_N/P. the layout is just two layers. Belows the differential pair Con-USB_N/P , there is no complete GND, even there are slots . is that right?
I am getting the Unknown Pin: Pin R1-1 but I checked the symbol and it has pins 1 & 2 and I checked the footprint and it has pads 1 & 2. Why am I still getting this error?
Great video Robert, why when you place a resistor, diode or p-channel mosfet after VCC altium says " VCC has only 1 pin " ? VCC>-------------/\/\/---------- another components. if you add 2 resistors in parallel after VCC the warning is not shown.
Hey m8, I would like to comment something. Why don't you just enable inside Clearance rules the box "Ignore Pad to Pad clearances withing a footprint" ?
It depends what your goal is. For example, if you need to be sure a PCB manufacturer with specific manufacturing capabilities needs to be able to manufacture your PCB, you may need to know about all the critical places on your PCB (including between pads) and fix the problem. "Ignore" doesn't fix problems, it only hides them (but there can be rules where it could be useful).
Great video! Yes the pin problem was noticed here after some strange errors and i found out that in my schematic i used pin 0 and 1 (programmers thing? 🙈🙈😂) and the footprint uses pads 1 and 2. I learn a lot because of Robert, very happy with your video’s!
Bro you're a Legend. You cover important topics that no one else cares. Thank you
Wow, this video was an absolute game-changer for me! I've been tirelessly searching through countless courses for hours, I truly felt stuck and overwhelmed as a beginner. This video covered everything I needed to know, and it made me feel like a happy kid again :DDDD
Also, the way you divided this video into parts is incredibly helpful
Thank youuu so much Robert!!
"Tadaaa no warnings!" That cracked me up! Great video Robert, thanks!
Thank you, i usually select the component and use the command "Align to the Grid". One tip, in the panel "PCB Rules and Violations" you can run directly only one rule by selecting it, right click "Run DRC Rule Class(..).".
Does "align with grid" works always reliably? PS: I didn't know about the right click, thank you for the tip!
@@RobertFeranec tnx sir today i solved the unknown pin issue .wity ur help.tnx
What a great video Robert!!! This could be a great debugging point for new Altium designers!! Thank you for your effort, keep going!!!
Thank you very much nikos antoniou
I have being days trying to fix my "pin error", really thanks, nice video and nice tutorial
Man, you saved me, Thank you very much for time spent on this video. Wish you all the best ^^
Amazing!! starting with Altium and got all of the errors :)
Thank you. You helped me a lot.
Great video Robert! I away learn something with your publications! Thanks!
Thank you for your all effort you are master of this job 👍
Thank you so much Robert I am very grateful for your videos
Sir I m a big fan of your teaching
This error always gets me. Even in your arduino pcb designing i could not figure out why did i have this error. Thanks for making it.
Yeah, I also do not know why this is happening - especially the cannot found footprint problem.
Thank you Robert, you're the Altium God
Here are my master again... Thanks a lot
Thank you very much Robert, you are great.
Great work sir..keep going on.. I found an error while updating sch to PCB that footprint is move to bottom layer and designator is in top overlay..
you are a genius!!! Thanks for all
Saved me so much time with that tip in fixing library issues. Thank you so much!
Great Video. Thanks Robert.
Very good explain!
Thanks, very helpful!!!
Regarding the off-grid problem, everything starts from that historical imperial unit. It should have been replaced with metric long time ago ;-)
Спасибо тебе, добрый человек. Какой-то негодяй назвал пины в своей библиотеке PCB не 1 и 2, а A и B, а я ее использовал и ничего не получилось.
TNQ Very Much
Sir please make a video on orcad on common error in schematic , PCB layout and essential point in pcb layout
Thanks for video
very nice video, very helpful
Is it absolutely necessary that we fix the off grid issue ? What happens if we ignore it provided the connections are properly done.
I have just also looked the wohle pcb form this schematic. I noticed that there are differential pair Con-USB_N/P. the layout is just two layers. Belows the differential pair Con-USB_N/P , there is no complete GND, even there are slots . is that right?
I am getting the Unknown Pin: Pin R1-1 but I checked the symbol and it has pins 1 & 2 and I checked the footprint and it has pads 1 & 2. Why am I still getting this error?
Please, help me. Fix error "Silk to solder mask clearance constraint " & "Un-routed net constraint" in PCB Rules and Violations
sir i have extra pin in net problem come when i go to schemtic to pcb layout , please sir help me
Thank you!
Great video Robert, why when you place a resistor, diode or p-channel mosfet after VCC altium says " VCC has only 1 pin " ? VCC>-------------/\/\/---------- another components. if you add 2 resistors in parallel after VCC the warning is not shown.
Hey m8, I would like to comment something. Why don't you just enable inside Clearance rules the box "Ignore Pad to Pad clearances withing a footprint" ?
It depends what your goal is. For example, if you need to be sure a PCB manufacturer with specific manufacturing capabilities needs to be able to manufacture your PCB, you may need to know about all the critical places on your PCB (including between pads) and fix the problem. "Ignore" doesn't fix problems, it only hides them (but there can be rules where it could be useful).
@@RobertFeranec This is true :-)
You are GOD!
Altium is the clunkiest program I have ever used compared to other board design programs, holy crap I hate it right now lol.
No connection IC pin makes a floating input pin error. How to fix it?
thanks man
Great video! Yes the pin problem was noticed here after some strange errors and i found out that in my schematic i used pin 0 and 1 (programmers thing? 🙈🙈😂) and the footprint uses pads 1 and 2.
I learn a lot because of Robert, very happy with your video’s!
Thank you Remy