आप का समझाने का जो तरीका है वह बहुत ही अच्छा है इलेक्ट्रॉनिक्स के मामले में आपको बहुत ही बारीकी से ज्ञान है आप की जितनी भी तारीफ की जाए उतनी कम है मेरा नाम संजीव है मैं गाने सुनने का बहुत ही शौकीन शौकीन हूं और बहुत सालों से मैं speed king बनाता चला रहा हूं 11 से 85 और 12 से 30 के जमाने से
Electrical specifications Unless otherwise stated, the results in Table 5 below are given for the conditions: VCC = 20 V, RL (load) = 8 , ROSC = R3 = 39 k, C8 = 100 nF, f = 1 kHz, GV = 21.6 dB, and Tamb = 25 °C. Table 3. Absolute maximum ratings Symbol Parameter Value Unit VCCMAX DC supply voltage for pins PVCCA, PVCCB, SVCC 30 V VI Voltage limits for input pins STANDBY, MUTE, INNA, INPA, INNB, INPB, GAIN0, GAIN1 -0.3 to 3.6 V Top Operating temperature -40 to 85 °C Tj Junction temperature -40 to 150 °C Tstg Storage temperature -40 to 150 °C Table 4. Thermal data Symbol Parameter Min Typ Max Unit Rth j-case Thermal resistance, junction to case - 2 3 °C/W Rth j-amb Thermal resistance, junction to ambient - 24 (1) 1. FR4 with vias to copper area of 9 cm2 - °C/W Table 5. Electrical specifications Symbol Parameter Condition Min Typ Max Unit VCC Supply voltage for pins PVCCA, PVCCB, SVCC - 8 - 26 V Iq Total quiescent - - 26 35 mA IqSTBY Quiescent current in standby - - 2.5 5.0 µA VOS Output offset voltage Play mode - - ±100 mV Mute mode - - ±60 mV IOCP Overcurrent protection threshold RL = 0 3.8 4.2 - A TjSD Junction temperature at thermal shutdown - - 150 - °C Ri Input resistance Differential input 48 60 - k
pls advice where to buy 60watt Class D Mono amplifier with MIC input only. No Bluetooth, No Pen drive connection. Want to use Direct MIC only. with three potentiometers
Bhai mujhe ek sought hai yeh amplifier board par 10000 mah 24 volt ke battery fixed karke agar kai ghanto tak chalana ne se kya hoga aap next video banao agar yeh karne se🙏🙏🙏🙏🙏
sir aap ka revew bhut acha lga me be bhi ye kit mngawaya he aap ye btaye kaa kiya 12 v ke sply pe 2 board yani aik hi power sply pe chal sake ge ya nhi
Sir is me Crossover laga k woofer mid or tweeter laga sakte h kya?? Ya bina crossover lagae full range speaker laga k kaam ho jaega?? Or speaker b kharab nhi hoga??
thank you for such informative videos! i have TPA3118pbtl hoping to get 90-100w on a 4ohm 10" 120w subwoofer. what modifications should i do? inductors : stock is good? 10uH value good for base output? or a higher value for a lower corner frequency? decoupling caps value 2200uF? any other changes is needed? thanks again .
Use 3ohm or 2ohm load , run it at 24v provide shit ton of heatsink and pray it doesn't go up in flames when the bass drops 💀. Datasheet says it can do 100w at 1% thd if given 26v at 3ohm load but to be safe stay at 24v. Put 10000uf 25v caps (buy many small caps and put them in parallel ) & remive the reverse polarity protection diode.
Dear Sudhir, can we get mono output from it? if yes then please try to make a short video. I am making a 2.1 configuration system as you suggested in a couple of videos.
Beautifully explained video. Sir Which board is perfectly match to make a Tower with 35 watt ,with two speakers and one woffer. For pleasing comfort Bass for a room.
i have one question, i want to make one low frequency sound wave fire extinguisher using 10 inch subwoofer, icl8038 function generator, is it possible? if yes then which battery should i use to give power supply, or if no then which components should i use to make this?
Lg hbs 730 headset k sth audio amplifier module use kiya h capacitor konsi value ka sahi rahega aur speaker h 4w 3ohm bass ate hi volume down or speaker dab raha koi solution please
Hi.. Sir, merepass jbl p2 studio speaker kharab hogaya, original board equal to new speaker pair. Please suggest the best amplifier board for jbl p2...
Sir man aap bola ke full vol pa es sound gayab ho jatie ha aap kah supply esu ha ya bord 60 watt ha man 18 0 18 5amp ka tarns or 50v 4700ka cap us kei ha to Kay kami hogee ab reply tell me Kay Karu sir please
Sir TPA 3118 Ko dc12v supply pr mere 2 speaker lagana h to is kit ke liye kitne ohm aur wt ka speaker suitable hoga aur sath me 1 twitter v connect krna h
10,12,15 inch ke speekar ke Karaoke ke spare parts ke bare mein puro knowledge ke sath ek video banaye sir jiska mai kaam karna chahta hu please sir you tube par koi bhi puri jankari wali vedio aaj tak nahi mili dekhne ko main 5 mahine se search kar raha hu 🙏🙏
What is best board for driving subwoofer above 50W ? Does MOSFET make difference for low frequency output quality ? Also make video on low pass filter DIY passive boards design.
Sir mujhe is board pe ek speaker & ek twitter chalana ha, kitna ohm ka speaker & kitna ohm twitter lagana ha & connect kaise karna ha, paralal ya siris me pls sir bataye
सर क्या 2092 आईसी का ड्राइवर सर्किट बन सकता है जो अलग से मॉसफेट लगाकर एक बड़ा एंपलीफायर बनाया जा सकता है इसके बारे में बताइए जैसे जैसे 500 w का बोर्ड होता है उसमें मॉसफेट एक्स्ट्रा लाकर क्या उसका पावर बढ़ाए जा सकता है
All these class D amps should be used Only for dialogue / speech hearing purpose or for Gaming purpose. For Music purpose only class AB amps should be used
Sir mere paas sony music system ke 2 box hai. 6ohm, 6.5 inch ke 50 watt + 50 watt ke speaker hai iske liye koun saa best amplifier rahega jisme voice or bass best ho plz tell me
Can you please make a video on tpa 3110 mono amp board. Because I have one borad but I think it is not giving proper output. It feels like Pam 8610 is more powerful than tpa 3110 mono.
I give 12v 2Amp supply & connect a 60watt 4ohm sub woofer work fine then I change the supply 24v 2.5 amp without any audio input after few minutes board short power adaptor indicator start blinking. Then I connect a 12volt 2 Amp adaptor same problem. My all adaptor working fine with other device. What is the issue? 24v + 60watt 4ohm damage the board orther components or IC? If IC then IC can work upto 26v in data sheet. But woofer say 8ohm. Any ideas from your end?
Sir muje ya puchna h ke tpa3118 amplifier board ka use krta hu. us mai battery connection bms ka use karta hu to muje ac to dc regulator ka use karana jaruge h kayyy.... Sir time mile to please sir reply kr deyna ,❤️
Hi bro ! I have a question . I have two class d amplifier TPA 3118 mono (60w) (8-24v)DC TPA 3110 stereo (15*2) (8-24v)DC Am using 19v3.45A DC adapter to opreate those two boards . But the problem is the board gets too hot . What to do bro? To reduce the heat . Although I placed two heat sinks respectively for each board but it become extreme hot and shut downs automatically.
hello sir, maine ye amp me 20 watt dc smps ke through diya and amp board achhi performance k baad ab koi sound output nahi de raha, mujhe nahi samajh a raha ki kya fault hui hai...plz reply and help us sir.
आप का समझाने का जो तरीका है वह बहुत ही अच्छा है इलेक्ट्रॉनिक्स के मामले में आपको बहुत ही बारीकी से ज्ञान है आप की जितनी भी तारीफ की जाए उतनी कम है मेरा नाम संजीव है मैं गाने सुनने का बहुत ही शौकीन शौकीन हूं और बहुत सालों से मैं speed king बनाता चला रहा हूं 11 से 85 और 12 से 30 के जमाने से
Class d diy is hard but just go for discreet ones. Their quality and working with them is a amazing and pleasure to make one .
❤❤❤❤Hi sir,4 door +dikky me 2 sub boofer verna car me music system lgana h. Kya 2 bord ko jood ker 4 door speaker+2 sub boofer banwa sakta hu???❤❤❤❤
3118 ek sath do board use karne par output badhegi kya
bohot kuch sikhne mila muje, thank you.
Sir can we use two 4 ohm speaker in series with this amplifier ?
Electrical specifications
Unless otherwise stated, the results in Table 5 below are given for the conditions:
VCC = 20 V, RL (load) = 8 , ROSC = R3 = 39 k, C8 = 100 nF, f = 1 kHz, GV = 21.6 dB, and
Tamb = 25 °C.
Table 3. Absolute maximum ratings
Symbol Parameter Value Unit
VCCMAX DC supply voltage for pins PVCCA, PVCCB, SVCC 30 V
VI Voltage limits for input pins STANDBY, MUTE, INNA, INPA,
INNB, INPB, GAIN0, GAIN1 -0.3 to 3.6 V
Top Operating temperature -40 to 85 °C
Tj Junction temperature -40 to 150 °C
Tstg Storage temperature -40 to 150 °C
Table 4. Thermal data
Symbol Parameter Min Typ Max Unit
Rth j-case Thermal resistance, junction to case - 2 3 °C/W
Rth j-amb Thermal resistance, junction to ambient - 24 (1)
1. FR4 with vias to copper area of 9 cm2
- °C/W
Table 5. Electrical specifications
Symbol Parameter Condition Min Typ Max Unit
VCC
Supply voltage for
pins PVCCA, PVCCB, SVCC - 8 - 26 V
Iq Total quiescent - - 26 35 mA
IqSTBY Quiescent current in standby - - 2.5 5.0 µA
VOS Output offset voltage
Play mode - - ±100 mV
Mute mode - - ±60 mV
IOCP Overcurrent protection threshold RL = 0 3.8 4.2 - A
TjSD
Junction temperature at thermal
shutdown - - 150 - °C
Ri Input resistance Differential input 48 60 - k
Sir how to convert aux output stereo to mono , kitna ohm ka resistance lagana padega ?
Sir es bord ham use karte ho ek problem dekha jab jab sound tej karte hue bord kam karna band kar deta hai.kue?
Active Band cross over ka vdo banaiye.
Frequency filter
Three type of band low, mid high.
Class D amplifier is the best
Sir, you're the best 👌. People who don't have great technical knowledge can understand things that we need. Thanks ❤
pls advice where to buy 60watt Class D Mono amplifier with MIC input only. No Bluetooth, No Pen drive connection. Want to use Direct MIC only. with three potentiometers
Bhai ji 10inch 2 spikro pr lga skte h bass ke liye please rply krna
Tpa 3110 vs tpa 3118 ka comper kre
Like first n then enjoying the hassle free knowledge.
Thanks for your valuable knowledge n hard work spreading with us.
Thanks bro.
@@WhatIThink sir kya yeh 12 volt car battery pe chl jayega
Bhai mujhe ek sought hai yeh amplifier board par 10000 mah 24 volt ke battery fixed karke agar kai ghanto tak chalana ne se kya hoga aap next video banao agar yeh karne se🙏🙏🙏🙏🙏
घर क् लिए आसान और बढ़िया bass का कोण सा बोर्ड ले और कीमत भी बताए
Sir aap Arduino ke baare me kuch samjha sakte h.... ye kya.... ha or kese kaam karta h
sir aap ka revew bhut acha lga me be bhi ye kit mngawaya he aap ye btaye kaa kiya 12 v ke sply pe 2 board yani aik hi power sply pe chal sake ge ya nhi
18 v 5 amp 4ohm de sakte hain ?
Bhai mere pass 30 watt 4 ohm ka spekear hai to kitna voltage mujhe dena padega
Sir is me Crossover laga k woofer mid or tweeter laga sakte h kya?? Ya bina crossover lagae full range speaker laga k kaam ho jaega?? Or speaker b kharab nhi hoga??
Very very nice video sir bhot badiya explain karta hai aap good work 🙏💕
Sirji kit ko transformr se chala ne ka video kijiye....smps to chale ga bt transformer me chalake video ki jiye plz....
Sir apne ek video me bataya tha shield wire uske bare me kuch batayenge
Hello Sir,
Isme 4ohms 25 watts ke do speaker series me connect kar sakte hai?
thank you for such informative videos! i have TPA3118pbtl hoping to get 90-100w on a 4ohm 10" 120w subwoofer.
what modifications should i do?
inductors : stock is good? 10uH value good for base output? or a higher value for a lower corner frequency?
decoupling caps value 2200uF? any other changes is needed? thanks again .
Use 3ohm or 2ohm load , run it at 24v provide shit ton of heatsink and pray it doesn't go up in flames when the bass drops 💀. Datasheet says it can do 100w at 1% thd if given 26v at 3ohm load but to be safe stay at 24v. Put 10000uf 25v caps (buy many small caps and put them in parallel ) & remive the reverse polarity protection diode.
Use 8 ohms speaker and 24v power supply this ic is not recommended for 4ohm load you can use tda7498 ic board which is 100×2 at 8ohm load
Sir please make a video on tda 7297 audio ic.... Clear high quality sound ke liea konsa best hoga ? Tpa 3118 Ya tda 7297 ??
Sir es amplifier board ky Sath 5inch ka subwoofer Chala sakty heen or Sirf bass nikaly ga ya sound bi .
Dear Sudhir, can we get mono output from it? if yes then please try to make a short video. I am making a 2.1 configuration system as you suggested in a couple of videos.
Ye mono hi hai ye wala particular board. Pbtl mode me hai
Beautifully explained video. Sir Which board is perfectly match to make a Tower with 35 watt ,with two speakers and one woffer. For pleasing comfort Bass for a room.
Phillips ka woox 2 speakers laga sakte he kya 6 ohm ka.... Aur 2 board se stereo bhi hoga na
60-60 watt k 2bspeaker lgne hai ya 30-30 watt k
Sir 10inch speaker jinki magnet 8 inch wali hoti uski liye konsa board use kru vadiya saaf awaz ke liye
Subwoofer mein LM1875 (Bass) ke badle yeh board use karne se longest clipping ho raha hein Quiu?
i have one question, i want to make one low frequency sound wave fire extinguisher using 10 inch subwoofer, icl8038 function generator, is it possible? if yes then which battery should i use to give power supply, or if no then which components should i use to make this?
Sir pls reply agr m is module me 12v dekar 30w lu Or woofer chalau kya mujhe acha bass or sound milegi
Lg hbs 730 headset k sth audio amplifier module use kiya h capacitor konsi value ka sahi rahega aur speaker h 4w 3ohm bass ate hi volume down or speaker dab raha koi solution please
Sir 3118 mai 2 way system 6 inch 8 ohm woofer pair box chalega kya
Hi.. Sir, merepass jbl p2 studio speaker kharab hogaya, original board equal to new speaker pair. Please suggest the best amplifier board for jbl p2...
Test this with better subwoofer, hitting is very good in this board
I have tested in 9"×6" sony coaxial speaker
Ye board me kaun si power supply pe best output milegi smps ya transformer based supply?
SMPS
Sir man aap bola ke full vol pa es sound gayab ho jatie ha aap kah supply esu ha ya bord 60 watt ha man 18 0 18 5amp ka tarns or 50v 4700ka cap us kei ha to Kay kami hogee ab reply tell me Kay Karu sir please
Speaker output me ac voltage bhi measure karke dikhye sir
Sir TPA 3118 Ko dc12v supply pr mere 2 speaker lagana h to is kit ke liye kitne ohm aur wt ka speaker suitable hoga aur sath me 1 twitter v connect krna h
Sir Keya hum is board par do 20w speaker series connection karke chala sakte hain?
Ye Tpa3118 Mono bord 12 Volt k Supply pe 4 Ohm pe Kitni Output deta hai ..
Waiting for 3110. Please suggest the idea to make soundbar from 3110.
Bhai mere pas 120watt ki subwoofer he
Usme kaun sa amplifier lagana chahiye??
Please suggest me
is board me 60w 8ohm subwoofer uskar sakta hu kya use Kiya do punch bass milega kya please pataye
Sir bahut achcha knowledge date ho
Namaste sir jee , 25w + 25w 8ohm speaker chalane k liye koi amplifier aur power supply suggest karenge please....?
Class D me tpa3118 aur AB me TDA2050 le sakte hain. Dono ki video hai aur power supply bhi batai hai maine
Thank u sir jee
Sir tpa 3116d2 & tpa 3118 ka pro logic amplifier board kaise hoga plz videos uploaded kare
Sir आप जो इसमे स्पिकर use किये है उसके बारे में जानकारी दीजिए... Please
TPA 3118 se 60watt subwoofer chala sakte hai kya
Sir ! Aisa tpa3118 ke do board ko bluetooth module se stereo sound produce kiya ja sakta h? Please sir ...
10,12,15 inch ke speekar ke Karaoke ke spare parts ke bare mein puro knowledge ke sath ek video banaye sir jiska mai kaam karna chahta hu please sir you tube par koi bhi puri jankari wali vedio aaj tak nahi mili dekhne ko main 5 mahine se search kar raha hu 🙏🙏
What is best board for driving subwoofer above 50W ? Does MOSFET make difference for low frequency output quality ?
Also make video on low pass filter DIY passive boards design.
Sir mujhe is board pe ek speaker & ek twitter chalana ha, kitna ohm ka speaker & kitna ohm twitter lagana ha & connect kaise karna ha, paralal ya siris me pls sir bataye
How did you manage to eliminate the noise in the speakers? What potentiometer did you use? Thanks for the video!
You can use any potentiometer as volume control on input.
Use 10k pot. 50k gives u more noise.
Sir isme bas eak speaker chla sakte hai 60 watt ka
Mere pas 15 watt ke 4 speakers hai mai un charo ko isme chlaumga to kya koi problem hogi
Hello sir 24 volt par kon sa borad accha chle gya
Tpa 3116 jaa tpa 3118
सर क्या 2092 आईसी का ड्राइवर सर्किट बन सकता है जो अलग से मॉसफेट लगाकर एक बड़ा एंपलीफायर बनाया जा सकता है इसके बारे में बताइए जैसे जैसे 500 w का बोर्ड होता है उसमें मॉसफेट एक्स्ट्रा लाकर क्या उसका पावर बढ़ाए जा सकता है
Ban sakta hai but class D ka circuit itna easy nahi hota...Bahut sare parameters hote hain.
Ye subwoofer konsa hai ..achchha bounce karta hai
Sir iyspe max kitna watt output nikalta hai or kitne watt ke spkrs laga sakte hai
40 watts
3110 vs 3118 kaunsa jyada powerfull hai
Kiya hum kisi bhi class d out put me manually inductor laga sakte hai
Isse 12v transformar se connect kar saktey hai ya 12v dc battery se hi chalega
All these class D amps should be used Only for dialogue / speech hearing purpose or for Gaming purpose. For Music purpose only class AB amps should be used
Sir mere paas sony music system ke 2 box hai. 6ohm, 6.5 inch ke 50 watt + 50 watt ke speaker hai iske liye koun saa best amplifier rahega jisme voice or bass best ho plz tell me
tpa 3116d .bhai
Sir ye 19 volt 3 amp laptop adapter se operate kr skte hai ya ye burn kr jaega plz reply sir
Sir,please tell me can i use sweton 2 woofer 20 watts 6 inches with it with 12v 7amps battery please Reply🙌🙌🙌🙌
Sir Kya hum 12v pe 4ohm 4owatt ka load de sakte hain 1speaker, amplifier kharab ya heat to nahi hoga please reply anyone
It will work.
Is it better than xy 100 L? Just in terms of quality
Sir I want to purchase 2 original bord from you
I purchased this bord from amazon but it was duplicate 28 pin
Can you please make a video on tpa 3110 mono amp board. Because I have one borad but I think it is not giving proper output. It feels like Pam 8610 is more powerful than tpa 3110 mono.
I give 12v 2Amp supply & connect a 60watt 4ohm sub woofer work fine then I change the supply 24v 2.5 amp without any audio input after few minutes board short power adaptor indicator start blinking. Then I connect a 12volt 2 Amp adaptor same problem. My all adaptor working fine with other device.
What is the issue? 24v + 60watt 4ohm damage the board orther components or IC? If IC then IC can work upto 26v in data sheet. But woofer say 8ohm. Any ideas from your end?
सर जी क्या इसमें १८वाट ५ampiyar ट्रांसफीमर से दे सकते पावर
Good afternoon sir mobile me kon si ( IC ) lagti or iski ek vedio banaiye
Aapne jo Bluetooth module use kiya hai uske make ka link share kijye please. Mujhe yaad aa raha aapne iska make upload kiya tha.
Sir tpa3118 d 2 par 30-30 watt ke speakers chala sakte hai
Yes but total ohms 8 hona chaahiye.
Ok and thanks
Sir series ya parallel connection me se kaun sa karna hai
Tpa 3118 d2 me speakers ke connection parallel karne hai yaa series kyoki 8 ohm banana hai.
sir 4 ohm 60w subwoofer chlane l liyein kitna volt dena hoga iss board ko?
Sir apka channel Mai nayahun iss board ke baremey janjari chahiye TPA3116D2 120W+120W Wireless Bluetooth 4.0 Audio Receiver Digital Amplifier Board
Sar isme directly Bluetooth panel laga sakte hain
Bro tpa3116d2 mono board ka rewiew de do na plz i want to buy it....
Sir muje ya puchna h ke tpa3118 amplifier board ka use krta hu. us mai battery connection bms ka use karta hu to muje ac to dc regulator ka use karana jaruge h kayyy....
Sir time mile to please sir reply kr deyna ,❤️
Not required
Bhai mene 1 bord liya he uska no sound hogya he,kya kare,sound nahi aarha,speaker wire short hogya he,repair hoga kyA
Hi bro ! I have a question . I have two class d amplifier
TPA 3118 mono (60w) (8-24v)DC
TPA 3110 stereo (15*2) (8-24v)DC
Am using 19v3.45A DC adapter to opreate those two boards . But the problem is the board gets too hot . What to do bro? To reduce the heat . Although I placed two heat sinks respectively for each board but it become extreme hot and shut downs automatically.
what is the load?
Sir isme hm 24v to nhi de sakte h pr iske power supply pr4700 ka capacitor lagane pr 24 v pr chala sakte h ki nhi sir jarur marg darshan karayiyega
subwoofer amp banane ke liye achhi lug raha h.
Ismein kitne inch aur kaun sa subwoofer lagaen deep bass Ke Liye please bataiye sar
Sir is board ke liye best output ke liye Power supply kitni deni hogi
Can I use 12v 3amp transformer
Sir out of pam8610 and tpa3118 which is one is best???
Isme 12 wat 8ohm ka 4 speaker chala sakte ha kya parallel
Bhai achhi quality ka speaker suggest kijiye bluetooth speaker banane k liye personal use k liye
Jo speaker ham amplifier board me connect karte to vo speaker ka watt kam hona chahiye ki jyada?
Very good sound quality, but unfortunately this board tpa3118 failed with no audio output. Two boards failed in the same way.
hello sir, maine ye amp me 20 watt dc smps ke through diya and amp board achhi performance k baad ab koi sound output nahi de raha, mujhe nahi samajh a raha ki kya fault hui hai...plz reply and help us sir.