Thank you sir... Maine aapka simulation wala sab videos dekha aapne bahut hi ache se samjhaya hai... Thank you so much for teaching me... Aal videos are very useful for us...
Thank you for the video! I have a question -what if I want to apply the force not on the surface but on the line, but not the edge line. How this can be achieved? How to add the force application line to the model?
Hi this is a really powerfull tool, I'm interested in simple flexure design and I would like to know if it possible to introduce the young modulus into solidwork to verify is your displacement won't go over the elastic range of a specific material on a specific hardness?
The materia information you can find in Metals hand book in ASTM standard dealing. Check the SOLIDWORKS value. But after make the fem simulation build the prototype validate real. Noting will be proved til you validate your project. Becarfull this is the most common engineer mistake
Thank you sir, I am very grateful for what I am learning from you. just a question about the yield strength. shouldn't it be that its red arrow goes up by applying less force? you know because it is showing the maximum acceptable yield strength and at the best it should exceed the highest applied stress. Also about the factor of safety. Should we compare it to for example 1.5 or there some other way to check it? thank you again
very nice sir can you compare solid works simulation with ansys simulation...... i mean if it is necessary to learn ansys after learning solid works simulation.....
May I ask what program do you use to record the screencast? cool tutorial and very useful And kindly do more videos on static analysis with all the external loads
Why is the mesh on the top face, mid way and to the back of the metal not even as it is in other areas, what has distorted the mesh. I don't mean near the holes, the mid way rear section....(on the left when facing the part that is bending)
When I'm being asked to define The Maximum Factor of Safety for applied force tension to tube member and to get the rid of applied forces into that member in a table, how can we solve this?
Good video, but I can tell you are not a structural engineer! Strain does not have a unit! There is no 'mm' or other unit for strain, it's just a dimensionless figure!!
Thank you sir...
Maine aapka simulation wala sab videos dekha aapne bahut hi ache se samjhaya hai...
Thank you so much for teaching me...
Aal videos are very useful for us...
deserve 1 million like good for refresh the steps for static analysis
please more video on simulation.thank you for your tutorials.
Vegen K Massihi Soon i will start full series of Solidworks Simulation,
@@CADCAMTUTORIALBYMAHTABALAM
Hey!
Do you have simulation tutorials for large assemblies?
this is the best youtube teacher
I hope u understand that’s good one I like it
Thank you for the video! I have a question -what if I want to apply the force not on the surface but on the line, but not the edge line. How this can be achieved? How to add the force application line to the model?
Hi this is a really powerfull tool, I'm interested in simple flexure design and I would like to know if it possible to introduce the young modulus into solidwork to verify is your displacement won't go over the elastic range of a specific material on a specific hardness?
The materia information you can find in Metals hand book in ASTM standard dealing. Check the SOLIDWORKS value. But after make the fem simulation build the prototype validate real. Noting will be proved til you validate your project. Becarfull this is the most common engineer mistake
Sir also make videos on other types of simulation.
Thank you sir, I am very grateful for what I am learning from you. just a question about the yield strength. shouldn't it be that its red arrow goes up by applying less force? you know because it is showing the maximum acceptable yield strength and at the best it should exceed the highest applied stress.
Also about the factor of safety. Should we compare it to for example 1.5 or there some other way to check it?
thank you again
Thank you very much Sir
very helpful - thanks
Please make video in braided hose sir
very nice sir
can you compare solid works simulation with ansys simulation......
i mean if it is necessary to learn ansys after learning solid works simulation.....
Ansys has more options than Solidworks simulation, i will try to cover Ansys in Future tutorials,
@@CADCAMTUTORIALBYMAHTABALAM you are the best teacher of solide works thank a lot
super . do some ansys tutorial
Thanks i will try ansys in future tutorials,
Can you show
How to change part area or volume
With safety
May I ask what program do you use to record the screencast ? cool tutorial and very useful
sir will you please make an video on shortcut settings and customization. thank you sir
Sabari Pandian sure i make soon for setting & customization tutorials,
CAD CAM TUTORIAL thank you sir for your fast response and i love the way you teach.🙌
Hi sir can I say one question can you send for me your emailadress
May I ask what program do you use to record the screencast? cool tutorial and very useful
And kindly do more videos on static analysis with all the external loads
u can use ice cream screen recorder
So non linear and linear dynamic study only available in premium version right?
weird thing is it still shows that it deforms even if I put 1N of force. it shouldn't do that.
Thank you
sir my results doesnt display strain result. may i ask how can i enable that? thanks you so much
Why is the mesh on the top face, mid way and to the back of the metal not even as it is in other areas, what has distorted the mesh. I don't mean near the holes, the mid way rear section....(on the left when facing the part that is bending)
When I'm being asked to define The Maximum Factor of Safety for applied force tension to tube member and to get the rid of applied forces into that member in a table, how can we solve this?
A box is placed on top of a aluminum plate, how do i simulate it to check if the aluminum plate can handle the weight of the box?
Define a remote load
Your breathing air is directly touching microphone and keep making bursting noise.
can you adjust the angle please?
Thank you.
Thanks i will take care in coming tutorial,
Good video, but I can tell you are not a structural engineer! Strain does not have a unit! There is no 'mm' or other unit for strain, it's just a dimensionless figure!!
Please clear your concept first then make videos....Though it's helpful for understanding how software works
Bloult