VMC Programming- Radius and Chamfer Cutting Program. Radius Program on VMC. Chamfer Program on VMC.

[@With_KDA_2765]

Sir douts clear krr diya aapne
Thank you❤🙏

[@premprakashshrivastava5710]

Sir radiaus banane ke liye end mill hum kisi bhi dai ka le skte h radius par effect nhi padega

[@premchandmahawarsp9359]

Good

[@onlineshoppingr.c3841]

Sir agar ham geometry mein tool Daya dal dete Hain to kya radius ya chamber program banane mein tool Daya calculate nahin karna padta kya

[@HinditechnicalHub]

yes

[@cadcamcncvmc]

Good job sir

[@Binodkumar-kb2pn]

Very knowledge full video guru ji 🙏

[@ManishSingh-wp8oq]

Sir ji
Fanuc series O-M
Es machine me ( D ) ki valu kaise daalte hai ,esme offset me samjh nahi aa raha ,kaise kar sakte hai please bata dijiye

[@sumitkumarsingh6450]

Good sir

[@vasimansari1919]

Very knowledge full video

[@sunilkumarverma9998]

Sir senter lene ke liye dia me tool ka half krke to senter lete h 75 +5 =80

[@DawonH]

Thank you always for good information. I hope to make many good videos in the future

[@HinditechnicalHub]

Okay dear

[@AjayKumar-mw3st]

Sir mujhe cmm report ke bare me jankari leni hai sir please ek bar btaiye sir

[@meeneshsharma8323]

Haas m same program chalega

[@someshwarraut4748]

Square block par upar half roud programme kaise banaye agar length jyada ho to

[@SUNILKUMAR-jm2tt]

Square pocket cavity cutting using g41' 42 ...plzz

[@HinditechnicalHub]

Okay

[@anangpalsingh9371]

Sir Mitsubishi me redius me kase dalte he g

[@pradeepr760]

sir please do tapper in vmc milling program

[@rahulkumawat8144]

Nice

[@thepb10rider]

Sir I. J. Ke value se bhi cornar radius lagta hai ya nhi ya only circle radius

[@someshwarraut4748]

Sir square block par upar radius half round kaise banaye

[@vasimansari1919]

Very good sir

[@shahrukhsheikh5378]

Pura side mill ka chamfer ka program banaye

[@NeerajSingh-cr2qs]

Sir jo apka job hai uska R6 hai and tool radies 10 hai kese

[@aloksen9650]

thank you sir

[@jasonjason3526]

Nice 👌👌👌👌

[@HinditechnicalHub]

Thanks

[@niteshkumarcnc8139]

Snap gauge setting karne ka tarika Dail snap gauge setting karne ka vedio daliye Sir ok

[@pratapsinhzala4875]

Thanks

[@lostghost8697]

Sir manual program banao na

[@vasimansari1919]

Radius ke program me.r.plus.kab.hoga.r.minus.kab.hoga.plz.sir.video.banaae

[@kishanlal7593]

r + - nahi ata

[@atulkhot7147]

Super 👌🏻🙏

[@rhjtcutes7457]

Sir aapse urgent help cahye

[@HinditechnicalHub]

Betao

[@niteshkumarcnc8139]

Bore gauge ka vedio daliye Sir ok Aap

[@HinditechnicalHub]

Okay

[@abhishektiwari-fp1pm]

Sir please explain setting in g54

[@SudhakarSudha-bf6ye]

Thanks sir

[@pradeepupadhyay3208]

Without G42 & G41 chamfer value kaise nikale

[@HinditechnicalHub]

Please Go to My Website = hinditechnicalhub.com

[@jogindermehra6211]

VMC machine me circumference Ka program kese bnaye

[@HinditechnicalHub]

drawing send kro. Controller kon sa gai

[@saxophonesongs6944]

Make prog. For 50 mm thick plate

[@HinditechnicalHub]

Drawing???

[@saxophonesongs6944]

Take any drg.

[@natureonwheels1222]

Sir ap sign X ke sign ulte kyu leye !! Left me X + hota he of right me - X hota he

[@sumitkumarsingh6450]

Good sir

[@nareshbabu980]

Nice