SUPMIX first cuts and a ride on the Side by Side.
ฝัง
- เผยแพร่เมื่อ 19 ส.ค. 2024
- Today I am right out of firewood so a good time to try out my new Supmix 54cc clone chainsaw.
I take the Hisun 700 Rhino clone side by side on the trails to haul the wood back home. **PLEASE CONSIDER SUBSCRIBING
🇺🇸 **USA AMAZON LINK TO THIS SAW *BLUE AND WHITE-amzn.to/42CHP8I
*RED-amzn.to/4bNser0
* REPLACEMENT CHAIN amzn.to/3UFSKML
*HUSQVARNA BAR OIL GREAT STUFF amzn.to/3SH3uYN
* SIDE TENTIONER UPGRADE amzn.to/4byShlx
*UPGRADED TOP HANDLEBAR amzn.to/4bDvLrO
*UPGRADED 20” OREGON BAR amzn.to/49BBKv9
CANADIAN AMAZON LINKS ONLY BELOW
🇨🇦
*** HERE’S A LINK TO THIS SAW-
amzn.to/3vYRoz6
Awesome video, great too see the wildlife running around .
@Jay Ferris thanks ya they love to be around where theirs noise. Feel safe from the Cougars,wolves and bears.
Getting wood keeping you busy 😎👍
@NORMS ATV yes sir that job never ends for me but I enjoy.
How’s your Poulan running?
@@Indeewoods i have never had a problem with it once start it idle great have had few poulans got more than my money worth .
Some yrs cut around 75 or so trees across atv trails never fails me 👍
@NORMS ATV awesome! Ya mine have been great as well. I cut lots of trees off the trail with my old wild thing lol
just got the same saw today lots of torque runs nice but the trottle lock was of the saw and in the saw bag so i glued it the center piece is missing i see its on yours. nice vid im fr nova scotia cheers
@waynebabin3646 yes the throttle locks are garbage and common to break especially in the cold.
I made a video not long ago how to fix that.
Great video bro 👍✌️
@eastcoastcabinfever thanks!
What kind of strew driver works the high an low strews. I got none that works it seems to have a little hole inside the turn strew
@eastcoastcabinfever for what saw the Supmix?
The Radley saws
@eastcoastcabinfever oh, ok you were commenting on my Supmix video so I was wondering what you meant there. Yeah it’s a special tool for the Radley. If you check that video I just put out on the Radley 3 year review It shows the tool that you need in there and it also has the link for the tool in the description of the video. You can order it off Amazon. It’s pretty cheap and you need it otherwise you can’t adjust the carb.
Always enjoy watching your vids. Did you ever find a solution to the weak on/off toggle switch? I guess worst case scenario a guy could jam the switch in the on position and kill the saw with the choke, but there must be a better way lol
@justindubya458 I tried trimming the rubber where the switch is thinking that there wasn’t enough of a gap, but it kept shutting off and honestly I’ve never fixed it yet, but I think the only fixes a different kill switch but of the same type. I have the same style switch on a couple of my other Clones and I have no issues so I think it’s just a low quality switch.
You could probably just go to a hardware store and get one from them that would be better quality.
I may throw a different style switch on it though when I get back into it
@@Indeewoods thanks, I'll search locally first if need be
Soup mix runs good!
That Chinese side by side really can take a load! Wow….
@Crazy Feller that was just a baby load compared to the last 6 or 7. Lol
@Crazy Feller and ya it runs good but it has lots of little issues you’ll see on up coming video when I go into more detail with it.
I picked up a neotec ncs6200 for $127 US recently. 34 stroke and 46 piston.
56.5 cc based on my calculations.
I was hoping it would be closer to what was advertised than many of the other clones-oh well….
Overall, not overly impressed with the quality of that one! Haven’t run it yet, tore it apart for some ticking first. Plastics are cheap, fitment is poor and the cylinder chamfers are bad…
I have been through 4 farmertec and their plastics are better, but the poor quality cylinder chamfers are similar. This is my fifth Chinese saw. After seeing how badly the piston wear is on my first 372, usually by the intake, I don’t even run them without pulling them apart first.
2nd 372- and two 288’s, just tore them apart before running them. They were running a deal on the 288 about this time last year for $239 US, so I picked one up.
My brother was so impressed, I sold it to him and bought another. Only problem with that one was the oil pump and the pistons are not right- bit pingy.
New oil pumps and meteor piston- all good. Starts up cold with 4-5 pulls, no air leaks- good saw…..
@Crazy Feller ya this one is going to need work. I can’t believe the sawdust that is bypassing the filter.
My Radley had some issues as well that I came up with a fix so hopefully I can figure these out because 166.00 CND is as cheap as it gets and they do make good power.
I never measured this one myself I was just going off what Kevin told me his measured out at.
54.5 c I think he said.
I’ll tear into it and see
The old shell has no ethanol. I was reading comments about the new 93 vpower and guys were saying they add ethanol to it now. Should test it.
Saw sounds like it's ported
@JalenRose02 it sure does I thought the same.
Looking forward to that old coal mine video
@Jack Blakeman yes I better finish Part 7 of my last excursion then onto new video series.
Lol 😂bought the same tuke! Not much snow up there
@peirules154 lol nice.
And there’s a couple feet here but higher up it’s 3-4 feet.
I have the same saw and my chainbreak doesnt work at all, the chain also likes to loosen, im hoping its just a bad chain and when i get a name brand itll stay tight
@The Canadian Wilderness hey just an update. So my chain was getting loose for the first few tanks but I just burned a full tank of fuel and my chain never got loose at all and after filing this chain and then my Stihl RS chain they feel the same harness.
The Supmix chain cutters are slightly wider and it cuts awesome!
Make sure your oiler is set high and keep a good sharp chain with good bar oil ( I use Husqvarna or Klondike bar oil.
@@Indeewoods gotchya! Appreciate the update, glad to hear the chain is ok
Another great outdoor adventure. I get a kick out of the crappy Chinese chainsaw names. What the names should be in my opinion 1. Radley=Crappy 2. Supmix=Soupmix=a recipe for disaster ! I will admit that they are better than nothing. Just kidding ! It will be interesting to see if you can modify them enough to get some use out of them, like you have done with the POOLANS. 😄😄😄
Haha “recipe for disaster” I love it!
Yes I have a little over 300 bucks tied up in those two saws so whats that 190.00 USD? No much and You’d be surprised that Radley is a good saw. For how long? I guess we’ll see but over two years old now and it cut piles and piles of firewood.
I really need to finish up my review on it.
Watch my videos on these clone saws they work great with proper fuels
Ya mine run good too I use good fuel/oil.
Not sure i can watch it... feels like I'm cheating on my radley....
@Rich Hubert lol