Hello. Great Video. My truck will not get in gear but there is no fault display. If I turn the switch to D, the screen still says N, when I turn the switch to Dm, it shows N and M . Same thing happens when I put in R, screen only shows N and when I put in Rm, It Show N and m. No change to D or R and there is no error code or alarm. Do you know why?
Thank you! If you don't have any fault code active it can be only one possibility.Every time i encounter this problem it was from the rnd switch.The switch from where you select gears.And a diagnose will help.to see in real time what happends when you select D or R.Good luck!
Hello.There can be two problems that causes that jumping.Either the Astronic has a problem,either the clutch kit,but you will need a diagnose to be sure.Have a good day
@@kylehoughton2578 Hello.First check under the hood in the top right connector box, if you have power on wire 43 300 when brake pedal is pushed.Also check all the abs and zbr fuses.If not some of the MAN trucks brake light switch location is typically situated near the brake pedal.
If this valve block is there.... Will it show on the dashboard.... I have 2008 MAN TGL 7.150.. D0834 engine ZF gearbox ... When I'm in first gear it shows 3rd on the dashboard... When I'm in 3rd gear it shows 6th gear on the dashboard....
Ussualy when this is happening it s because an electrical fault.A bad sensor inside the as tronic module,if it s about automatic gearbox.If its manual gearbox the problem is from the valve block.
Hi I have man 2014 TGM Automatic.It Is showing some time gearbox ecu also creating bit noise from the place of clutch booster. When I restart or restart after some time. It’s disappearing. May I know. What will be the issue.
Hello.First you will need a diagnose.The bit noise appears because clutch booster cannot engage, and the can be from the pressure plate,pressure bearing or clutch booster.So just to be sure you need to make a diagnose on the gearbox.
@@RelectrikRepairs because i face the same problem in man truck today and try soo hard to find the issues but i can't so i will release the parking brake and tray again. Thank you so much for answering me and keep going bro
@@osamamohamedaliismail6177 Many thanks!Do that and if that warning message still appears and also a beep, you can have a failed sensor on the parking brake valve,which indicates if the parking brake it s applied or not.Good luck!
@@osamamohamedaliismail6177 And also that warning message appear if the parking brake is released and the driver door open!Sometimes it is because a switch in the door lock
@@RelectrikRepairs i get your points So i will check this _Release parking brake _parking brake valve _door lock switch And i will try again Thanks a lot
Þhi mate i am.not sure if you can assist i have a man tgs 27 440 2012 model it takes all gears retard works but when u stop completely it goes to neutral N then u need to reselect D for it to move not sure what it could be
Hi.If you don't have any tcu or ffr fault on the screen ,you will need an diagnose to check everything on the gearbox and see exactly whats happening .Good luck🙏
@@RelectrikRepairs the writing is not English.when you start the engine,sometimes it starts and go off and when you start and the engine is stable,gas won’t accelerate and the gear won’t pick up
Mille Grazie per il vostro servizio🎉🎉🎉 Auguriiii! Happy new year 🎉🎉🎉
Thank you, bro! Happy new year🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉
I’m a same problem concerning the gear but at the same time, the gas doesn’t accelerate and sometimes the engine goes off when working
Happy New year Brother
Grasias amigo🎉🎉🎉🎉
❤❤❤
Merci frère
Hello. Great Video. My truck will not get in gear but there is no fault display. If I turn the switch to D, the screen still says N, when I turn the switch to Dm, it shows N and M . Same thing happens when I put in R, screen only shows N and when I put in Rm, It Show N and m. No change to D or R and there is no error code or alarm. Do you know why?
Thank you! If you don't have any fault code active it can be only one possibility.Every time i encounter this problem it was from the rnd switch.The switch from where you select gears.And a diagnose will help.to see in real time what happends when you select D or R.Good luck!
Thanks
i have man TGM
what is problem gear jumping from 2 to 6 and 8 ?
Hello.There can be two problems that causes that jumping.Either the Astronic has a problem,either the clutch kit,but you will need a diagnose to be sure.Have a good day
❤
Hello sir I have a problem with a Man tgs 33.360. I have no rear brake light. Just wanted to know where is the brake switch located
@@kylehoughton2578 Hello.First check under the hood in the top right connector box, if you have power on wire 43 300 when brake pedal is pushed.Also check all the abs and zbr fuses.If not some of the MAN trucks brake light switch location is typically situated near the brake pedal.
You didn't say it would have been adjusted
If this valve block is there.... Will it show on the dashboard....
I have 2008 MAN TGL 7.150..
D0834 engine ZF gearbox ...
When I'm in first gear it shows 3rd on the dashboard...
When I'm in 3rd gear it shows 6th gear on the dashboard....
Ussualy when this is happening it s because an electrical fault.A bad sensor inside the as tronic module,if it s about automatic gearbox.If its manual gearbox the problem is from the valve block.
@@RelectrikRepairs hello... Not seeing a valve block
@@alvesthegreat The valve block is that one wich has a round plug.On the top of the gearbox.
Good
I got same problem here eeesh
Hi
I have man 2014 TGM Automatic.It Is showing some time gearbox ecu also creating bit noise from the place of clutch booster. When I restart or restart after some time. It’s disappearing.
May I know. What will be the issue.
Hello.First you will need a diagnose.The bit noise appears because clutch booster cannot engage, and the can be from the pressure plate,pressure bearing or clutch booster.So just to be sure you need to make a diagnose on the gearbox.
@@RelectrikRepairs thank you so much
Great job
But why when you shift to D or R there is a warning massage "shift to natural" ?
Thanks
Thank you.Warning message was because the parking brake was not applied when i've shifted to D/R!
@@RelectrikRepairs because i face the same problem in man truck today and try soo hard to find the issues but i can't so i will release the parking brake and tray again.
Thank you so much for answering me and keep going bro
@@osamamohamedaliismail6177 Many thanks!Do that and if that warning message still appears and also a beep, you can have a failed sensor on the parking brake valve,which indicates if the parking brake it s applied or not.Good luck!
@@osamamohamedaliismail6177 And also that warning message appear if the parking brake is released and the driver door open!Sometimes it is because a switch in the door lock
@@RelectrikRepairs i get your points
So i will check this
_Release parking brake
_parking brake valve
_door lock switch
And i will try again
Thanks a lot
hy! what diagnose tool do you use?
Hello.I use launch and autocom,but launch it's better.
Thank You!@@RelectrikRepairs
Þhi mate i am.not sure if you can assist i have a man tgs 27 440 2012 model it takes all gears retard works but when u stop completely it goes to neutral N then u need to reselect D for it to move not sure what it could be
Hi.If you don't have any tcu or ffr fault on the screen ,you will need an diagnose to check everything on the gearbox and see exactly whats happening .Good luck🙏
I’m a same problem concerning the gear but at the same time, the gas doesn’t accelerate and sometimes the engine goes off when working
Hello.You may have also a problem on the edc(engine) because acceration don't work.What are the faults on the instrument cluster?
@@RelectrikRepairs the writing is not English.when you start the engine,sometimes it starts and go off and when you start and the engine is stable,gas won’t accelerate and the gear won’t pick up
@@eliyasukeshood3834 Does the N* blinks? Also it s important to me,what error code is shown on the display.
After you start,it will appear an error code on the display :an edc,tcu or ffr fault code
❤❤❤