Thanks for video. Just tore my son's 2001 Honda 400ex down last night. It was turning over slow despite replacing one way bearing and starter. Much to my consternation the crank and piston stood erect when jug came off. Crank is discolored blue telling me it is heat seized. Still rotate, barely, by hand. As a result I have been scouring internet for upper and lower rebuild/big bore/stroker kit. This particular kit is one of the two I had already narrowed possibilities to. Looks like I too will be purchasing and building along. Tore my 2004 Yamaha Warrior down as well my son blew up when riding. It too was a result of crank bearing failure. Jug cracked, piston broken, but fortunately case not cracked. Trying to focus on the positive. Looks like I will be installing upper and lower rebuild/big bore/stroker kit on it as well. Going to be a busy and expensive winter! New subscriber and look forward to following along with your build while I do my two. Already purchased some goodies for Warrior that are going on too; like oil cooler and new shifter. Already put new Banshee front shocks and 300ex rear on Warrior; makes it sit and handle better for 50yo, 6ft, 240lb man than factory. Never thought I would be so excited to put 300ex shock on anything let alone improve rideability without breaking the bank. Been out of quad scene for about 25yrs. Built big bore/stroker, 411cc, 1985 Honda 350x engine in 1999 that I put in 300ex I had. Took swingarm off 350x (little longer), put front wheels on backwards (little wider), and Works shocks all around. Smoked stock 400ex back then with extra gear (350x was 6spd). I was just physically too big at 6ft/220lbs for 300ex frame. Hoping for similar performance out of my 2004 Warrior once it is finished. Warrior fits my body type much better than 300ex; especially now after minimal modifications.
That's just what comes along with these older bikes bro. I have other videos splitting and rebuilding 400ex bottom ends that should be very helpful for you
@@garagemcmatt measured piston on 400. 440 Franken kit of some sort in it already. For 440 she must have been tightening up since I purchased in April. Based on previous Honda ATVs I have owned, this should have performed better than it did as a 440. Or, stock starter just struggled with higher compression piston. Anyhow, thought I would be catching up with my Warrior 400 rebuild. In light of new info and 465 kit going on 400ex I will still get smoked in the open by my boy! Thanks again for video, comment, and info.
While I'm waiting for parts, bought winch and light bar for my 1998 Kawasaki Prairie! Put new tires on the old girl this spring; finally replaced factory, Dunlop, bologna skins! Always tell friends and family they picked the wrong 400 when they choose the Honda 400ex over the Kawasaki 400 Prairie! And she at least isn't blown up! These new mega quads with independent suspension and 4wd (Can Ams, King quads, etc.) make trail riding challenging when they are rutted up and the old Prairie is stuck from high centering with live rear axle! Wading through mud and water with come along was getting old to drag her out! Can't throw this machine around by hand like the Warrior and 400ex. Bring it into 21st century with an electric winch and handle bar mounted LED light bar! The Prairie 400 May not be a sport quad but she is reliable; and still running at this point. Happy new year!
im defintely tuned in... new to your channel and i work on alot of 400exs and your videos definitely i see are going to be helpful. keep me tuned in because oneday im going to buy one of these custumers rolling chassis and start me some videos and build me uo one myself. keep em coming
Keep up the great videos. Just picked up an 04 myself and these videos are a lot of help. Maybe some time in the future you can do a jetting video. How to choose and decide on what jets to run
Do you have to have your cases machined for that cylinder cuz I just bought 89 mm cylinder and I had it sleeve by BP racing and I got to have my cases machined
I'm waiting for my appointment at the one place I like to go to for stuff like that to be done then I'm ready to build the quad. That's the only thing holding me up. Did you use my promo code for 10% off at bpratv.com?
@@garagemcmatt he's building the cylinder right now he said he charged me when he's done I'll use the promo code I appreciate that thanks bud hey seems that you have a whole lot of ATV parts either some parts that you want to sell I'm putting one together for my wife from scratch .
Ever run a crf450r timing chain? Thats what i run in my stroker 440 build and its pretty much bullet proof. It didnt require any mods. It fits in the stock guides but its 2 full plates wider per link.
@@garagemcmatt also just a heads up. The hotrods cranks right out of the box are at or above the service limit out of true. I shipped mine out to crankworks to be balanced and trued. Had to have mine balanced for my custom 87mm stroker piston. I stroked the 416 bore for reliability. With your 465 build you will be needing a minimum of a 39mm carb. It will benifit greatly from a 41 or 42mm though. The stock 400ex carb will be incapable of properly fueling it. I tried with my build and had a 230 main and a 60 pilot and still couldnt keep it from being scary lean.
@@brentpfeiffer4043 I'm going to true the crank myself. I was looking at a 39mm fcr or a lectron, I'm not sure which way I'm gunna go with the carb yet tho
@@garagemcmatt Great idea! My research confirmed that hotrods doesnt make a bad product. Most of the early failures were from being shipped not secure enough. When crankworks sent me my crank back it was like chissling a fossil out of rock. It was wrapped and spray foamed and wrapped and spray foamed and inside a box full of packing peanuts. Wrapped that in bubble wrap and in a second box lol. They made absolutely sure it could be used as a football and not hurt anything. I measured mine at .010 out of the box. Had crankworks confirm my findings. They measure it at closer to .009. But the factory service limit was like .007 or .005 something of that nature. (Its been 2 years since my build). When i got it back from crank works it was at .002! Keep up the good content man! Bringing back the 400ex for sure! Here i thought i was the only one crazy enough to drop that kind money on one lol
how familiar are you with tuning carbs? i have a 416 big bore kit with a stage 2 hotcam and Full race port and polish head assembly with valve cover and a race exhaust. any recommendations on what jets i should use ?
Was there anything you had to modify on crank cases dealing with the 465 build? And also did you run stock clutches or did you go high performance and if so what brand would you recommend?
#portedhead. Great video bro. Only thing I'd like to know is what size crank u have? +2 mil? +4mil???? Have u tried any other stroker crank for these trx400? Bro that fly on the camera though lol Arturo Medina
I used bpratv.com a few times, I don't have any complaints with my experience with them. This exact kit I used to build my engine is all built just sitting on the shelf if u just want to buy a fully built engine. Garagemc549@gmail.com
Wait till you guys see the video I filmed today it's longer then my normal videos but I can't wait to hear your guys comments on it.
Thanks for video. Just tore my son's 2001 Honda 400ex down last night. It was turning over slow despite replacing one way bearing and starter. Much to my consternation the crank and piston stood erect when jug came off. Crank is discolored blue telling me it is heat seized. Still rotate, barely, by hand.
As a result I have been scouring internet for upper and lower rebuild/big bore/stroker kit. This particular kit is one of the two I had already narrowed possibilities to. Looks like I too will be purchasing and building along.
Tore my 2004 Yamaha Warrior down as well my son blew up when riding. It too was a result of crank bearing failure. Jug cracked, piston broken, but fortunately case not cracked. Trying to focus on the positive. Looks like I will be installing upper and lower rebuild/big bore/stroker kit on it as well. Going to be a busy and expensive winter!
New subscriber and look forward to following along with your build while I do my two. Already purchased some goodies for Warrior that are going on too; like oil cooler and new shifter. Already put new Banshee front shocks and 300ex rear on Warrior; makes it sit and handle better for 50yo, 6ft, 240lb man than factory. Never thought I would be so excited to put 300ex shock on anything let alone improve rideability without breaking the bank.
Been out of quad scene for about 25yrs. Built big bore/stroker, 411cc, 1985 Honda 350x engine in 1999 that I put in 300ex I had. Took swingarm off 350x (little longer), put front wheels on backwards (little wider), and Works shocks all around. Smoked stock 400ex back then with extra gear (350x was 6spd). I was just physically too big at 6ft/220lbs for 300ex frame. Hoping for similar performance out of my 2004 Warrior once it is finished. Warrior fits my body type much better than 300ex; especially now after minimal modifications.
That's just what comes along with these older bikes bro. I have other videos splitting and rebuilding 400ex bottom ends that should be very helpful for you
@@garagemcmatt measured piston on 400. 440 Franken kit of some sort in it already. For 440 she must have been tightening up since I purchased in April. Based on previous Honda ATVs I have owned, this should have performed better than it did as a 440. Or, stock starter just struggled with higher compression piston.
Anyhow, thought I would be catching up with my Warrior 400 rebuild. In light of new info and 465 kit going on 400ex I will still get smoked in the open by my boy! Thanks again for video, comment, and info.
While I'm waiting for parts, bought winch and light bar for my 1998 Kawasaki Prairie! Put new tires on the old girl this spring; finally replaced factory, Dunlop, bologna skins! Always tell friends and family they picked the wrong 400 when they choose the Honda 400ex over the Kawasaki 400 Prairie! And she at least isn't blown up!
These new mega quads with independent suspension and 4wd (Can Ams, King quads, etc.) make trail riding challenging when they are rutted up and the old Prairie is stuck from high centering with live rear axle! Wading through mud and water with come along was getting old to drag her out! Can't throw this machine around by hand like the Warrior and 400ex. Bring it into 21st century with an electric winch and handle bar mounted LED light bar! The Prairie 400 May not be a sport quad but she is reliable; and still running at this point. Happy new year!
@@jasonsippola183 I liked the Prarie we had here it was fun for as heavy as it was
I have a 465 stroker 400ex that I trail ride . People say there not reliable but if you build it right they last .
I heard that too. Thanks for the comment bro
@@garagemcmatt love the videos keep up the great work
@@owenvedder7882 thanks bro wait till you see tomorrow's video
@@owenvedder7882 how do you like your 465 is it fast
@@garagemcmatt I beat 450s with eis.
Would love to try this kit out, can’t wait to see you ride this thing!
Me too bro me too. Thanks for the comment
Love to see a 416 build🤘🏽🤘🏽personally working on trying to get one done
I have one coming in for the other 400ex from bpratv.com
im defintely tuned in... new to your channel and i work on alot of 400exs and your videos definitely i see are going to be helpful. keep me tuned in because oneday im going to buy one of these custumers rolling chassis and start me some videos and build me uo one myself. keep em coming
You came at the rite time the 465ex is getting started this week. If u are looking for a roller holla at your boy I got them stacked up over here
I just recently discovered your channel. Looks like some nice 400’s come from your garage! I miss the 400ex keep up the good work
Thanks bro stay tuned we are going to do a 400ex give away in the hopefully near future at a certain amount of subs. Thanks for the comment.
Keep up the great videos. Just picked up an 04 myself and these videos are a lot of help. Maybe some time in the future you can do a jetting video. How to choose and decide on what jets to run
Yeah I'll cover that when the time comes. I'm thinking of what carb I want to order. Thanks for the comment
Great video always got our back thank you
Thanks bro. Thanks for the comment
Do you have to have your cases machined for that cylinder cuz I just bought 89 mm cylinder and I had it sleeve by BP racing and I got to have my cases machined
I'm waiting for my appointment at the one place I like to go to for stuff like that to be done then I'm ready to build the quad. That's the only thing holding me up. Did you use my promo code for 10% off at bpratv.com?
@@garagemcmatt he's building the cylinder right now he said he charged me when he's done I'll use the promo code I appreciate that thanks bud hey seems that you have a whole lot of ATV parts either some parts that you want to sell I'm putting one together for my wife from scratch .
@@donaldsearles817 email me garagemc549@gmail.com if I have it and don't need it I'll sell it
Ever run a crf450r timing chain? Thats what i run in my stroker 440 build and its pretty much bullet proof. It didnt require any mods. It fits in the stock guides but its 2 full plates wider per link.
I have heard of it that's probably what this (super heavy duty) chain is originally
@@garagemcmatt also just a heads up. The hotrods cranks right out of the box are at or above the service limit out of true. I shipped mine out to crankworks to be balanced and trued. Had to have mine balanced for my custom 87mm stroker piston. I stroked the 416 bore for reliability. With your 465 build you will be needing a minimum of a 39mm carb. It will benifit greatly from a 41 or 42mm though. The stock 400ex carb will be incapable of properly fueling it. I tried with my build and had a 230 main and a 60 pilot and still couldnt keep it from being scary lean.
@@brentpfeiffer4043 I'm going to true the crank myself. I was looking at a 39mm fcr or a lectron, I'm not sure which way I'm gunna go with the carb yet tho
@@garagemcmatt Great idea! My research confirmed that hotrods doesnt make a bad product. Most of the early failures were from being shipped not secure enough. When crankworks sent me my crank back it was like chissling a fossil out of rock. It was wrapped and spray foamed and wrapped and spray foamed and inside a box full of packing peanuts. Wrapped that in bubble wrap and in a second box lol. They made absolutely sure it could be used as a football and not hurt anything. I measured mine at .010 out of the box. Had crankworks confirm my findings. They measure it at closer to .009. But the factory service limit was like .007 or .005 something of that nature. (Its been 2 years since my build). When i got it back from crank works it was at .002! Keep up the good content man! Bringing back the 400ex for sure! Here i thought i was the only one crazy enough to drop that kind money on one lol
@@brentpfeiffer4043 lmao no your not the only one bro wait till you see my next video to just how crazy I am. 😜
how familiar are you with tuning carbs? i have a 416 big bore kit with a stage 2 hotcam and Full race port and polish head assembly with valve cover and a race exhaust. any recommendations on what jets i should use ?
Look up some specs on the cam recommendations and start with that bro
Was there anything you had to modify on crank cases dealing with the 465 build? And also did you run stock clutches or did you go high performance and if so what brand would you recommend?
It's a different crank and the opening that the cylinder skirt slides into has to be opened up slightly. And I'm going to run all wiseco on the 465
Give us an update. Just picked up one of these quads for free. Actually not in to bad of shape.
The 465ex will start being worked on after the 450r is done. That's cool you got a killer deal bro.
What is the best cam for a 416 The one I have in there keeps getting chewed up
I'm a fan of the stage 2 hot cam. How is it chewed up from the rockers?
One is not Egg shaped no more I don’t know if it’s the rocker they look good
@@garagemcmatt I’ll have to send you a picture
@@mangog6710 send pics to my email bro. Garagemc549@gmail.com
@@garagemcmatt ok
What’s the estimated hp on a build like that?
I'm not really sure bro. Have not seen anything similar that was dynoed
What would do bro for the best midrange kit 426 or bigger thanks man keep rolling strong on the best honda videos I have seen in a min
The 426 I built is a fun quad with the stage 2 hot cam. It has plenty of power
#portedhead. Great video bro. Only thing I'd like to know is what size crank u have? +2 mil? +4mil???? Have u tried any other stroker crank for these trx400? Bro that fly on the camera though lol
Arturo Medina
The 465 is a 5 mil I believe. Stay tuned I just split the cases today to start building the stroker 465ex engine
how long did it take them to ship out your ordered after you ordered from them? 2 week?
Mine took a month
9 days after I ordered it showed up I'm in new jersey too.
@@chase8545 I'd be pretty pissed off if that's the case i wanna finish my build and just ride man.
@@garagemcmatt I'm not to far from you i live in pa
@@skittlesmodz2939 your in PA ok I'm like 30 mins from philly
THE FLY!
ITS ANNOYING!
Lmao I know bro I didn't even know till I edited the video. I was like wtf bro
Just stumbled on your channel. Good content. I’m looking at a big bore kit for my raptor 660. I’ll use your promo and help you out. Thanks
I appreciate that bro we have other promo codes for other companies too and also have over 110 videos out ty for the comment and welcome
How much is the kit
It all depends what you ad or subtract from the kit
#portedhead I can not wait tell this things done!!
Yeah me too bro
Hi this dealer is trusted? Can I order???
I used bpratv.com a few times, I don't have any complaints with my experience with them. This exact kit I used to build my engine is all built just sitting on the shelf if u just want to buy a fully built engine.
Garagemc549@gmail.com
The code doesn’t work anymore
I'll call them and find out. This video was over 5 or 6 months old too. Should still be good tho