Great info Elvis, but fell asleep 5 times before you got to the point ......... Sry buddy, love you videos but could you get to the point and stop getting off topic every 5 seconds ... PLEASE
Based on my experiences 99% of the cycling problems with 300AAC Blackout are due to being under-gassed caused by an undersized gas port. It seems that most of the barrel manufactures design and build the barrels with gas ports designed for running suppressed. Running a suppressor gives the gas system a sizable boost in gas pressure, thus the undersized gas ports. Even a quality well respected mfg barrel can have undersized gas ports( my Wilson Combat 11.3 inch pistol gas port barrel was undersized and wouldn't even run supers reliably unsupressed). My biggest problem is that the 300AAC Blackout premise was that the only changes needed on the AR15 platform was a barrel change. With the correct sized gas port this is true. Without it they will not cycle properly. Everyone has suggested fixes from special buffer springs, super heavy buffers, lightweight BCG's and the list goes on and on. One channel even suggested that by changing the extractor it fixed the short cycling. A properly set up barrel should run without adding any special band-aids. More then likely your Palmetto State Armory BCG just needs to be broken in some. The parkerized finish is nowhere near as smooth/slick (even when lubed) as your Nickle Boron BCG. Great series on loading up 300AC Blackout by the way!
hey Papa's Place... yes yes and yes! people will do about anything to a rifle.... Until it accidentally works!!! : )... Im somewhat familiar with your 300 build.. I watched some of that on your channel.. And I don't recall if I mentioned the bcg would maybe be fine once broke in.. but i might have to adjust my sub bullet recipe. Or not... I'll run that Bcg in a couple rifles and break it in. And give it a shot again.Im glad you chimed in. It's good info for those who read through the comments. Thanks my friend!!
@@dacoelec I just got a 8.5 BA modern series pistol barrel that won’t cycle factory fiochi 135gr or S&B 200gr subs what should the gas port be sized to , I’m most likely never getting a can I just want it to eat everything I will mention it did cycle my 110gr hand loads with 18.4-18.8-19.4gr of Win296 and 175gr nosler Eld with 18gr of cfe I’m not sure what is going on if I’m running a brand new sharps reliabolt, an adjustable gas block wide open with mill spec buffer and spring 🤷🏽
@@gsmithy7995 I drill out the port until it cycles 230gr hand cast powder coated with 11.5 gr CFE BLK. I'm also using a 1.75" x 10" can on a 7" barrel. BCA side charging upper. I use number bits and it's not unusual to be at least 5 to 10 bits larger. Guns are like people and some have a cantankerous personality. Be sure and use a good quality spray gun lube like Amsoil and don't hesitate to shoot wet. It's a bit messy but it sure helps subsonic to cycle. Best regards.
I built my 300blk piece by piece and is pretty much the same setup you have.I casted 50 of the lee bullets and powdercoated them and shot them at the indian river public shooting range up in whitmire this past weekend and they all shot without any issues,but the accuracy went from good to bad,my groups were all over the target until I ran out of bullets,when I got home I cleaned my rifle and it appeared that I had some leading about 5 inches into the barrel.I used the harbor freight red powder coat . I also shot 40 s&w and 9mm casted bullets powder coated in the same color and they shot wonderfully without any leading issues.I hope to have another batch made up and back up to the range to test them out,I would love for you to come out and witness and maybe even document the test.
hey Mike Haigler. .. I've never had any leading in my rifle. just one thought. make sure you flair the case before seating the bullet. . cutting into the bullet and pc can cause a problem!
Good info Elvis, I had some failure to feeds in my 300 blackout as well with my standard bolt shooting subs as well until I started running it dripping wet. Now runs the subs just fine! Never had issue with supersonic. Thanks for all the great videos and education!
hey Crazycasting bonnifield....It sounds like it just needed a good breaking in!!! thats my feeling on this one. I think the nickel boron bolt may allow me to make a somewhat lighter load (over all ) thanks so much again for watching and commenting!!!!!!
I made the mistake of buying a mid gas length barrel. The NEMO spring helps for subs, but if the rounds aren't right, they won't chamber. I ended up neck turning, and seating deeper. I'm using the NOE 225 gn FB version of the missile. I found that swapping in my old .223 BCG made a big difference as far as cycling goes, but didn't solve things 100%. Not sure how I missed this video, butif I'd seen it, I would definitely have done things differently.
I started out with a nickel boron bolt/carrier in my 10.3 suppressed 300blk. Failures to feed next round and lock back. So. Yea. Working on a spring now.
With my sub sonic 300 blackout set up, I ended up going with a light buffer and spring to get it to cycle properly. I weighed 5 buffers and they ranged from 2.9 oz. to 4.9 oz. The 3.0 oz buffer with light weight spring is the one I ended up with that made things cycle fine in mine. I do not recommend it for supersonic. The bolt slams to hard. I think it is best to tune the gun for the ammunition you will be using.
Did you ever think about the Getting an adjustable gas block Like most builders say you can shoot High velocity by turning down the gas And when you go to shoot low velocity turn up the gas
another great video elvis. I too replaced my factory steel bolt w the same nickel boron bolt you have and I can vouch that its less maintemance as well... less lube and lesser cleaning after! money well invested! be safe man.
People get too caught up in the treatments and coatings on these parts. We are testing an ar platform now that has 5,000 rounds thru it without cleaning anything in the rifle caliber pistol. Instead of wasting money worried about the treatment or coating a critical part has,worry about the function and design of that part. A great example of this is the HMB battle bolt. It's the most innovative bolt in the entire industry but noone has talked about it for the last two years. It solves a critical failure point in the ar platform while solving some other what could be problems. They also solved a second known failure point in the ar platform with their monobloc barrels. Since their recent government contracts the .300blk out monobloc barrels are hard to get your hands on but they can be found. This company even solved harmonic issues that can occur with.223/5.56, .308/7.62 , and .243. This isnt so much an issue in with the 5.56 but it definatly makes a huge difference with the long range rifles. I have never shot one of their rifles that has had greater than sub moa accuracy. Why carrier functioned when one didnt in this video has nothing at all to do with the treatment/finish. But let's pretend it is due to the finish. As soon as it gets any fowling kr dirt on it at all,it doesnt function. Sorry for the rant. Lol
Richard Petty threw together old, extra paint & got Petty Blue. Now it looks like you made Speckled Elvis. I think people need to take gas port size into account with 300 BO. Many are made to use with suppressors & that could result in undergasing if a suppressor isn't used.
hey Shananagans5.... yea no doubt ! Just one more piece of the puzzle.. Not to complicated though as long as you do a little homework. The problem comes from people trying to reinvent the wheel , a good bit of the time a least!!! thanks for contributing to the conversation!!!!
Elvis I'm having problems making coments on utube. So hope you get this. Good stuff you put out . would you do a video on free play. the distance from the projectal to the lands on a blackout.
Went to the range yesterday to shoot my fresh 300blkout build and it shot 1 time, after a 2nd feed attempt b/c the 1st pull it didnt go.. so it shot 1 time then just wouldn't again.. i was thinking the firing pin 🤔.. but on a 2nd thought I minds well give tht Bolt carrier group u mentioned a shot
You may have answered this already. I have a 16 inch 300 blackout with a 5.56 lower. (Not that it really matters) with no suppressor. I want to be able to shoot subsonic 220 grain ammo unsurpassed. Will the ammo cycle? Obviously I haven't tested it yet. I don't want to have a stupid injury if I can prevent it.
Good information. If I can I will always buy NB bcg when available. Drum roll made me laugh out loud. wasnt sure what that was so I had to rewind a couple of times. Still laughing. Take care
hey JAM4photography... the nickel is the way to go for sure with the 300 blk.... the drum roll... I'm guessing, was the squerrel knocking the hickory nuts out of the tree on the roof...... those things can knock you out! time to eat squerrel! !! ; )
oh man that squirrel has perfect timing. I thought it was kind of a weird sound effect. Thanks for clarifying. I have to say its always fun to hear some kind of animal or bird in your videos. Makes it seem like Im right there with you outdoors.
+JAM4photography thanks Jam,, there was some good bird chirping in there too I noticed! but them big hickory nuts getting knocked can sound like automatic gun fire!!!! ; )
Elvis ammo, Hi, in your experience, what's the ideal gas tube length for a 300 blk running a 16 inch barrel with a standard 3/4 inch port ? Pistol? Carbine? Mid? Your insights on this would be appreciated.
What would cause a 300 blackout to just stop working I checked and changed my gas block even took a coil out of the buffer spring and it still fails to strip the next round off the mag using American eagle red box and hornady polymer tips neither will lock the bolt back on empty running carbine gas system, is it possible that somehow my barrel warped and is letting gas out of the block
Yo Elvis! Cast a bunch of the 300blk lee 230gr. At 10.8 4227 it doesn’t want to cycle my 16” carbine length gas AR. . They group unbelievably well, but don’t cycle. Coated with Hi-Tek coating. . Can’t decide if I want to go up in a ladder, order a barrel with a pistol length gas system, or bore my carbine length gas port. @2A_CaliGuy I’ll post the videos soon.
Key takeaway. Understand 300 gassing with pistol powders. An adjustable gas block is step one. Any other component change is just a band-aid for not having step one.
@@Subtlenimbus Correct, but our shop has yet to see an undergassed/undersized 300 barrel port. As a rule, most AR’s are deliberately overgassed for reliability. Throttle it back and create yourself a soft shooter. Add a rear angled tanker style compensator to make it super soft.
Hey Elvis I need your expertise help ...iam building a 300blackout pistol 10.5 barrel now I don't know what buffer spring and weight to use please let me know what u think I'm thinking of the gueissele super 42 spring combo breided spring and weight please let me know what you think.. time is of Essen thanks
This is old as fuck but I just did another 10.5 300bo shooting supers and it's not locking back or chambering next round. It's not the gas block. I took the spring out and it's a 1/4 inch longer than another buffer spring I had. Dunno if that'll fix it or not. Bcg doesn't seem to be binding on the gas tube so I'm at a freaking loss man.
Hey can you please help I have 2 of the same palmetto state arms 7.5 300blk uppers got my wife one and myself one it shoots 150 grain perfect even in gen2 pmag but it won’t chamber subs even 190 grain with gen 2 pmag-Window 556-pmag300blk mags or lancer 200 grain 300blk mags I tried Nemo arms battle light 300blk bring and even took weights out buffer and it still gets stuck when chambering I tried messing with the weights using no weights all the way to using all tungsten with both springs same issue
11.55 oz on the mil-spec and the nickel boron at 11.65 oz is only a tenth of an oz. difference...Elvis what am I missing here bud? A 43.749 grain difference between them...I thought the lighter bolt carrier would function and the heavier would not, but I thought there was maybe 4 oz or better difference between them. So, the answer is the slickness difference? Oh yeah....what about those pure lead tests...I'm waiting with 'baited bean breath!'
hey there Charles Irby,,,, It goes to show ya you are the only one paying attention!!! thats quite a big mathematical miss calculation ..... : ) That nickle is slick as crapola! It is in fact one part of the solution to make it all go easy on ya! still got the green mist scheduled there Bean breath... : ) And Im bringing xtra drawers with me on that Squach hunt!!!
Go to that link and listen to the latest 2 or 3 sasquash programs, they will give you a good basic understanding about their calls and their hunting of animals...dang cool El! I hope you don't get eaten El...I kinda like you...:) charlie
Some of you are gonna hate me saying this but you should not get drunk and then post to TH-cam video About firearms It's OK to drink it's OK to have firearms and shoot fires but it's not OK to drink and try to talk about how to fix them
Great info Elvis, but fell asleep 5 times before you got to the point ......... Sry buddy, love you videos but could you get to the point and stop getting off topic every 5 seconds ... PLEASE
1.5x...
Way too long for the point you're making. But, thanks for sharing your experience.
Based on my experiences 99% of the cycling problems with 300AAC Blackout are due to being under-gassed caused by an undersized gas port. It seems that most of the barrel manufactures design and build the barrels with gas ports designed for running suppressed. Running a suppressor gives the gas system a sizable boost in gas pressure, thus the undersized gas ports. Even a quality well respected mfg barrel can have undersized gas ports( my Wilson Combat 11.3 inch pistol gas port barrel was undersized and wouldn't even run supers reliably unsupressed).
My biggest problem is that the 300AAC Blackout premise was that the only changes needed on the AR15 platform was a barrel change. With the correct sized gas port this is true. Without it they will not cycle properly. Everyone has suggested fixes from special buffer springs, super heavy buffers, lightweight BCG's and the list goes on and on. One channel even suggested that by changing the extractor it fixed the short cycling. A properly set up barrel should run without adding any special band-aids.
More then likely your Palmetto State Armory BCG just needs to be broken in some. The parkerized finish is nowhere near as smooth/slick (even when lubed) as your Nickle Boron BCG.
Great series on loading up 300AC Blackout by the way!
hey Papa's Place... yes yes and yes! people will do about anything to a rifle.... Until it accidentally works!!! : )... Im somewhat familiar with your 300 build.. I watched some of that on your channel.. And I don't recall if I mentioned the bcg would maybe be fine once broke in.. but i might have to adjust my sub bullet recipe. Or not... I'll run that Bcg in a couple rifles and break it in. And give it a shot again.Im glad you chimed in. It's good info for those who read through the comments. Thanks my friend!!
1000 up votes! Enlarging the gas port has never failed me yet on .300 BO subsonic.
@@dacoelec I just got a 8.5 BA modern series pistol barrel that won’t cycle factory fiochi 135gr or S&B 200gr subs what should the gas port be sized to , I’m most likely never getting a can I just want it to eat everything I will mention it did cycle my 110gr hand loads with 18.4-18.8-19.4gr of Win296 and 175gr nosler Eld with 18gr of cfe I’m not sure what is going on if I’m running a brand new sharps reliabolt, an adjustable gas block wide open with mill spec buffer and spring 🤷🏽
@@gsmithy7995 I drill out the port until it cycles 230gr hand cast powder coated with 11.5 gr CFE BLK. I'm also using a 1.75" x 10" can on a 7" barrel. BCA side charging upper. I use number bits and it's not unusual to be at least 5 to 10 bits larger. Guns are like people and some have a cantankerous personality. Be sure and use a good quality spray gun lube like Amsoil and don't hesitate to shoot wet. It's a bit messy but it sure helps subsonic to cycle. Best regards.
I built my 300blk piece by piece and is pretty much the same setup you have.I casted 50 of the lee bullets and powdercoated them and shot them at the indian river public shooting range up in whitmire this past weekend and they all shot without any issues,but the accuracy went from good to bad,my groups were all over the target until I ran out of bullets,when I got home I cleaned my rifle and it appeared that I had some leading about 5 inches into the barrel.I used the harbor freight red powder coat . I also shot 40 s&w and 9mm casted bullets powder coated in the same color and they shot wonderfully without any leading issues.I hope to have another batch made up and back up to the range to test them out,I would love for you to come out and witness and maybe even document the test.
hey Mike Haigler. .. I've never had any leading in my rifle. just one thought. make sure you flair the case before seating the bullet. . cutting into the bullet and pc can cause a problem!
With that color combo, it reminds me of a miniature 20 mm Vulcan 😃
Good info Elvis, I had some failure to feeds in my 300 blackout as well with my standard bolt shooting subs as well until I started running it dripping wet. Now runs the subs just fine! Never had issue with supersonic. Thanks for all the great videos and education!
hey Crazycasting bonnifield....It sounds like it just needed a good breaking in!!! thats my feeling on this one. I think the nickel boron bolt may allow me to make a somewhat lighter load (over all ) thanks so much again for watching and commenting!!!!!!
Explain dripping wet please.
@@SBSATS lots of lubricant
Well Elvis Ammo the conclusion of another great video man thanks. Wake up America
thanks Way2goRule.... I think America has one eye open! that's it! thanks for watching with both eyes brother!
I made the mistake of buying a mid gas length barrel. The NEMO spring helps for subs, but if the rounds aren't right, they won't chamber. I ended up neck turning, and seating deeper. I'm using the NOE 225 gn FB version of the missile. I found that swapping in my old .223 BCG made a big difference as far as cycling goes, but didn't solve things 100%. Not sure how I missed this video, butif I'd seen it, I would definitely have done things differently.
Thanks Elvis I really appreciate all the information you put out there
I started out with a nickel boron bolt/carrier in my 10.3 suppressed 300blk. Failures to feed next round and lock back. So. Yea. Working on a spring now.
With my sub sonic 300 blackout set up, I ended up going with a light buffer and spring to get it to cycle properly. I weighed 5 buffers and they ranged from 2.9 oz. to 4.9 oz. The 3.0 oz buffer with light weight spring is the one I ended up with that made things cycle fine in mine. I do not recommend it for supersonic. The bolt slams to hard. I think it is best to tune the gun for the ammunition you will be using.
Did you ever think about the Getting an adjustable gas block Like most builders say you can shoot High velocity by turning down the gas And when you go to shoot low velocity turn up the gas
another great video elvis. I too replaced my factory steel bolt w the same nickel boron bolt you have and I can vouch that its less maintemance as well... less lube and lesser cleaning after! money well invested! be safe man.
thanks Andres Crespo.... I get great results and it sounds like many others do too! good shooting to ya!!
People get too caught up in the treatments and coatings on these parts. We are testing an ar platform now that has 5,000 rounds thru it without cleaning anything in the rifle caliber pistol. Instead of wasting money worried about the treatment or coating a critical part has,worry about the function and design of that part. A great example of this is the HMB battle bolt. It's the most innovative bolt in the entire industry but noone has talked about it for the last two years. It solves a critical failure point in the ar platform while solving some other what could be problems.
They also solved a second known failure point in the ar platform with their monobloc barrels. Since their recent government contracts the .300blk out monobloc barrels are hard to get your hands on but they can be found. This company even solved harmonic issues that can occur with.223/5.56, .308/7.62 , and .243. This isnt so much an issue in with the 5.56 but it definatly makes a huge difference with the long range rifles. I have never shot one of their rifles that has had greater than sub moa accuracy.
Why carrier functioned when one didnt in this video has nothing at all to do with the treatment/finish. But let's pretend it is due to the finish. As soon as it gets any fowling kr dirt on it at all,it doesnt function. Sorry for the rant. Lol
I would absolutely love to hear the end of this video but damn if you were not kidding he is putting me to sleep 🤣🤣
God said knowledge is power and any man that does not seek knowledge is a fool.
Thanks for the knowledge
Hey man, good news, ford light blue, worked absolutely perfectly! Thank you so much!
hey Eadc Components. .. man o man!!!! thank God brother. ... I'm so happy. .. I wanted to swim the the pond and get it done for ya!!! : ) awesome!
Flawless On Range Day
😉😁
Richard Petty threw together old, extra paint & got Petty Blue. Now it looks like you made Speckled Elvis. I think people need to take gas port size into account with 300 BO. Many are made to use with suppressors & that could result in undergasing if a suppressor isn't used.
hey Shananagans5.... yea no doubt ! Just one more piece of the puzzle.. Not to complicated though as long as you do a little homework. The problem comes from people trying to reinvent the wheel , a good bit of the time a least!!! thanks for contributing to the conversation!!!!
Elvis hay brother ,how are you doing . I don't have a 300 black out as of yet . But I now where to go for good info . Straight to you . Thanks nick
hey Nick L ... you got it brother .... im right hear when ya need me!!!!! thanks again...
Elvis I'm having problems making coments on utube. So hope you get this. Good stuff you put out . would you do a video on free play. the distance from the projectal to the lands on a blackout.
what buffer spring and weight are you using?? is there a combo that will work with both super and subsonic??? wana sell some ammo?? lol
Went to the range yesterday to shoot my fresh 300blkout build and it shot 1 time, after a 2nd feed attempt b/c the 1st pull it didnt go.. so it shot 1 time then just wouldn't again.. i was thinking the firing pin 🤔.. but on a 2nd thought I minds well give tht Bolt carrier group u mentioned a shot
interesting stuff, like the shop as well.
If I close my eyes really tight!!! I can swear it’s Forrest Gump talking !
You may have answered this already. I have a 16 inch 300 blackout with a 5.56 lower. (Not that it really matters) with no suppressor. I want to be able to shoot subsonic 220 grain ammo unsurpassed. Will the ammo cycle? Obviously I haven't tested it yet. I don't want to have a stupid injury if I can prevent it.
I can’t believe you could possibly ever get anything done in your life.
So did you ever find out exactly what was wrong with the PSA BCG? Or are we just spitballing at ideas?
Great info! My piston guns all have NB BCG also. Thanks for the tips.
thanks 2003harleyguy... some places, they are most needed! it was interesting the way I learned. .... thanks again! !!
thanks for all the solutions! lol have another drink......
Boat carrier?
My 300 functions great Elvis with a nitrided bolt that is slick like nickel boron just throwing that out there!!
Ta ta today!!! Terrible. Couldn't finish
It would be helpful to know buffer spring and buffer weight. And extracted spring o ring present or not.
For those looking for the solution: better BCG lubricity
Good Info. I will keep it in mind.
thanks again Vengenace Early.... thanks for watching and commenting!
Thanks for making the video
7.62 x 39 bolt barrel and mag
Solution
Good information. If I can I will always buy NB bcg when available. Drum roll made me laugh out loud. wasnt sure what that was so I had to rewind a couple of times. Still laughing. Take care
hey JAM4photography... the nickel is the way to go for sure with the 300 blk.... the drum roll... I'm guessing, was the squerrel knocking the hickory nuts out of the tree on the roof...... those things can knock you out! time to eat squerrel! !! ; )
oh man that squirrel has perfect timing. I thought it was kind of a weird sound effect. Thanks for clarifying. I have to say its always fun to hear some kind of animal or bird in your videos. Makes it seem like Im right there with you outdoors.
+JAM4photography thanks Jam,, there was some good bird chirping in there too I noticed! but them big hickory nuts getting knocked can sound like automatic gun fire!!!! ; )
elvis ammo I bet you wear a helmet outside! Wake up America🇺🇸
+Way2go Rule That's a good one!
Elvis ammo,
Hi, in your experience, what's the ideal gas tube length for a 300 blk running a 16 inch barrel with a standard 3/4 inch port ?
Pistol?
Carbine?
Mid?
Your insights on this would be appreciated.
What would cause a 300 blackout to just stop working I checked and changed my gas block even took a coil out of the buffer spring and it still fails to strip the next round off the mag using American eagle red box and hornady polymer tips neither will lock the bolt back on empty running carbine gas system, is it possible that somehow my barrel warped and is letting gas out of the block
Yo Elvis!
Cast a bunch of the 300blk lee 230gr. At 10.8 4227 it doesn’t want to cycle my 16” carbine length gas AR.
.
They group unbelievably well, but don’t cycle. Coated with Hi-Tek coating.
.
Can’t decide if I want to go up in a ladder, order a barrel with a pistol length gas system, or bore my carbine length gas port.
@2A_CaliGuy I’ll post the videos soon.
Key takeaway. Understand 300 gassing with pistol powders. An adjustable gas block is step one. Any other component change is just a band-aid for not having step one.
Unless your gas port is too small, which is usually the problem. Adjustable block is only useful if you are over gassed.
@@Subtlenimbus Correct, but our shop has yet to see an undergassed/undersized 300 barrel port. As a rule, most AR’s are deliberately overgassed for reliability. Throttle it back and create yourself a soft shooter. Add a rear angled tanker style compensator to make it super soft.
Mil spec 11.55 oz
NBoron. 11.65 oz. 0.10 oz heavier not 10 oz
=
Hey Elvis I need your expertise help ...iam building a 300blackout pistol 10.5 barrel now I don't know what buffer spring and weight to use please let me know what u think I'm thinking of the gueissele super 42 spring combo breided spring and weight please let me know what you think.. time is of Essen thanks
Did you get an adjustable gas block for that thing?
Hey Elvis would you be interested in making some videos about swaying 22lr brass into 223 bullets?
hey mick russ ..... not sure about that one. But not to say Im not fascinated by it ... Me being me I cant help but to appreciate the process!
What is the message again?
Ever look into time travel?
Its ok bro i talk like im learning disabled too❤️
11.65 - 11.55 = 0.1 or one tenth of an ounce difference.
great video i changed my bolt to a
After "breaking in" the mil-spec bolt did it change the performance?
This is old as fuck but I just did another 10.5 300bo shooting supers and it's not locking back or chambering next round. It's not the gas block. I took the spring out and it's a 1/4 inch longer than another buffer spring I had. Dunno if that'll fix it or not. Bcg doesn't seem to be binding on the gas tube so I'm at a freaking loss man.
What's a Boat Carrier?
Hey can you please help I have 2 of the same palmetto state arms 7.5 300blk uppers got my wife one and myself one it shoots 150 grain perfect even in gen2 pmag but it won’t chamber subs even 190 grain with gen 2 pmag-Window 556-pmag300blk mags or lancer 200 grain 300blk mags I tried Nemo arms battle light 300blk bring and even took weights out buffer and it still gets stuck when chambering I tried messing with the weights using no weights all the way to using all tungsten with both springs same issue
Are you saying that if you drop a single cartridge by hand into your chamber, that it will not go all the way in? Like the overall length is too long?
Teal is the color!
11.55 oz on the mil-spec and the nickel boron at 11.65 oz is only a tenth of an oz. difference...Elvis what am I missing here bud?
A 43.749 grain difference between them...I thought the lighter bolt carrier would function and the heavier would not, but I thought there was maybe 4 oz or better difference between them. So, the answer is the slickness difference?
Oh yeah....what about those pure lead tests...I'm waiting with 'baited bean breath!'
hey there Charles Irby,,,, It goes to show ya you are the only one paying attention!!! thats quite a big mathematical miss calculation ..... : ) That nickle is slick as crapola! It is in fact one part of the solution to make it all go easy on ya! still got the green mist scheduled there Bean breath... : ) And Im bringing xtra drawers with me on that Squach hunt!!!
Go to that link and listen to the latest 2 or 3 sasquash programs, they will give you a good basic understanding about their calls and their hunting of animals...dang cool El! I hope you don't get eaten El...I kinda like you...:)
charlie
+Charles Irby what link you talking about?
+Charles Irby I found it ... should have known youtube sent it to spam!
Ok we see it.
I don't know if this guy should have firearm or not .
My problem was with the SuperSonics
I want to incorporate a folding stock on a 300 Blk
You appear to have oodles of time........good for you buddy.
Is this still a proboem
No problem!
Should of been smart like him and got cast...hard to find 30 cal hullets
h4895 is a kickass powder imr3031 is prob a lil better for sub 300
hey the baddest ... good to know some other powders to try! thanks again for watching! !!!
11.55 compared to 11.65 is only .10 of an once.
Looks like Christmas!! Really
Try drinking AFTER you record you video... If you were to edit out all the fluff and get to the point, you'd have a good 2 minute video.
HEY!!
Diz' steel merka', hain'it ???!!
Ahhhhhh kin dureeink eeeiny tyme uahh wantsa' !!!
Doeuwnn like it? Then makeurine video, on urine damn tyme!
Was the nickel boron from PSA as well?
Hey Matt Lord.. No the BCG. Was from Hardened Arms.
What....zzzzzzzz! And what's with the hands? 😂
Ummmm.....this video is ummm....a little hard to ummm...... follow ummmm...but thanks for ummm....the advice
a little slow there Forest...
Make a to the point video bro.
Lead poisoning
umm. much?
0/10 Not enough UMM
Ummm.... 😂
As slick as a babies rear end? I think you need to work on that one bud.
Yeah... Sorry : )
Umm umm ummm umm umm
You said you ordered everything to be as reliable as possible, then you said Palmetto State Armory..................
I stopped listening after that
Some of you are gonna hate me saying this but you should not get drunk and then post to TH-cam video About firearms It's OK to drink it's OK to have firearms and shoot fires but it's not OK to drink and try to talk about how to fix them
Holy adhd
.....um.......um......um....um
sorry, but this guys voice was so annoying it messed me up while playing battlefield.
Dont make videos high.
Um um um every tenth word um
Solution? Get a real gun.
230 grains ? Really