I wish I had the shop to do stuff like this, incredibly jealous! I'd love to make a 6 cavity mold with 3 different bullet designs in it. You could make an assortment of rounds with every cast!
I love how the molds look. How much for a pair of 6 cavity (to fit Lee 6 cavity mold handles) 180gr. Wadcutter 40S&W grooveless molds. I powder coat right now but might try MCC looks simpler and faster. Can pre pay via PayPal, ppm me with cost and lead time.
Hi, ich habe die Geschossform bei google gesucht (für 150grain), die Maße übertragen und dann den Fräser aus HSS angefertigt. Der Pinolenhub an meiner Fräse hat eine digitale Anzeige, wodurch ich die genaue Tiefe einstellen kann. Alternativ würde auch eine Messuhr funktionieren. Man kann es auch leicht nachrechnen, indem man den unteren Teil des Geschosses als Zylinder und den oberen als Kegelstumpf annähert. Damit kann man genau ausrechnen, wie groß die Bohrtiefe sein muss.
Are you just doing trial and error to get the cutter to the right size and shape to get the correct bullet grain? I cut down a .32 caliber rifle bullet mold so it would make lighter .32 acp bullets, but I had to cut little bits off at a time, cast bullets, weigh them, then cut some more to get from 100 grain bullets to 71 grain bullets. Making the entire mold that way would mean making a cutter, a mold, casting bullets, weighing them, then scrapping everything to start over if it's off wouldn't it?
No you're doing it wrong. Very simple you take the original bullet you cut it down to where you want it and you weight it if you screw up no big in fact before I made changes to mold I could modify several bullets and see how they shoot easily done on a lathe and it also helps if you have collet chuck 6 jaw chuck leaves a lot less marks on the bullet. Than you can use milling machine or even lathe with 4 jaw chuck to but down that's how I did my first one before I got milling machine.
nice, how much might a custom die of 4-6 bullets cost? I'm looking for one for 160-180 grain 308 diameter for 30-30, 308 and 300 win mag, also a custom mold for 338 win mag also
sehr interessantes video, nahezu meditativ ;) was ich mich immer gefragt habe, wie bestimmst du, wie tief du bohren musst, um ein bestimmtes geschossgewicht zu erhalten ? ich würd gerne 358er machen mit ca 150gn und 9mm mit 125gn. hast du einen tipp für mich ? lg hellboy
Fettrillen rausfräsen würde ich von abraten, da man die Kokille nie genau ausgerichtet bzw. den Fräser auch nicht absolut zentriert bekommt. Zudem muss man dann auch noch einen für das Kaliber passenden Fräser haben bzw. eine Reibahle. Einen Fräser in der Geschossform kann man sich z.B. bei MP- Molds fertigen lassen, was aber sicherlich einiges kosten wird. Ich habe meine Fräser immer aus HSS gedreht und dann die Schneiden mit einem Dremel hinein geschliffen.
darauf hätt ich kommen können :) wo kann man sich einen entsprechenden fräskopf fertigen lassen, oder wäre es viel wirtschaftlicher einfach aus einer etwas leichteren kokille die fettrillen rauszufräsen ?
Here's a question for you. Why would you go through all the trouble of making a mold that you can buy for $25? I mean you did a really good job but I think I'd rather spend the time casting bullets or reloading.
If you saw his sprue plate you would realize it's for automatic casting machine. You can't just buy a bold for $25 for it. Also the aluminum that cheap Lee uses is not as good as better molds like NOE uses.
More than that...the molds looks absolutely fantastic in reality...I'll try to make an video this week to show them at work.
I wish I had the shop to do stuff like this, incredibly jealous! I'd love to make a 6 cavity mold with 3 different bullet designs in it. You could make an assortment of rounds with every cast!
Running the Tap Under Power for Threads... Yes!!!
Not only beautiful work but an entertaining and well made video as well! Thumbs up!
This profile with no Grease groove is perfect for powder coating
Hello brother, how is this cutter made, how polished? Thank you
I love how the molds look. How much for a pair of 6 cavity (to fit Lee 6 cavity mold handles) 180gr. Wadcutter 40S&W grooveless molds. I powder coat right now but might try MCC looks simpler and faster.
Can pre pay via PayPal, ppm me with cost and lead time.
Hi,
ich habe die Geschossform bei google gesucht (für 150grain), die Maße übertragen und dann den Fräser aus HSS angefertigt. Der Pinolenhub an meiner Fräse hat eine digitale Anzeige, wodurch ich die genaue Tiefe einstellen kann. Alternativ würde auch eine Messuhr funktionieren.
Man kann es auch leicht nachrechnen, indem man den unteren Teil des Geschosses als Zylinder und den oberen als Kegelstumpf annähert. Damit kann man genau ausrechnen, wie groß die Bohrtiefe sein muss.
Are you just doing trial and error to get the cutter to the right size and shape to get the correct bullet grain? I cut down a .32 caliber rifle bullet mold so it would make lighter .32 acp bullets, but I had to cut little bits off at a time, cast bullets, weigh them, then cut some more to get from 100 grain bullets to 71 grain bullets. Making the entire mold that way would mean making a cutter, a mold, casting bullets, weighing them, then scrapping everything to start over if it's off wouldn't it?
No you're doing it wrong. Very simple you take the original bullet you cut it down to where you want it and you weight it if you screw up no big in fact before I made changes to mold I could modify several bullets and see how they shoot easily done on a lathe and it also helps if you have collet chuck 6 jaw chuck leaves a lot less marks on the bullet. Than you can use milling machine or even lathe with 4 jaw chuck to but down that's how I did my first one before I got milling machine.
GunsNpolitics e
That is a good bullet design. But, what of lubricant grooves?
nice, how much might a custom die of 4-6 bullets cost? I'm looking for one for 160-180 grain 308 diameter for 30-30, 308 and 300 win mag, also a custom mold for 338 win mag also
Thank you very much! By the way...
How the bullet case is made?
Sir, after watching that you have another subscriber, just the type thing I was looking for, so thank you for the heads up for some great ideas 👍👍👍
where can I buy it please that for cal .357
Did you say your going to make me a .729 Diablo mold?
hello friend, u could tell me how I make or where I can buy a formwork mold to manufacture pellets for 4.5mm rifles pressure ? thank you.
.177-4.5 is it the same process
That is awesome. Wish I had that kind of equipment
Will u make 9mm bullet mold and sell it??
Awsome Colt 357's i am in love with these muthafuckers easy to carry and concele and the stopping power and range is more than acceptable
How would you cut the driving bands and still have a lube groove?
It's obviously for bullets that get Powder Coated or Hytec coating
sehr interessantes video, nahezu meditativ ;)
was ich mich immer gefragt habe, wie bestimmst du, wie tief du bohren musst, um ein bestimmtes geschossgewicht zu erhalten ? ich würd gerne 358er machen mit ca 150gn und 9mm mit 125gn.
hast du einen tipp für mich ? lg hellboy
Fettrillen rausfräsen würde ich von abraten, da man die Kokille nie genau ausgerichtet bzw. den Fräser auch nicht absolut zentriert bekommt. Zudem muss man dann auch noch einen für das Kaliber passenden Fräser haben bzw. eine Reibahle.
Einen Fräser in der Geschossform kann man sich z.B. bei MP- Molds fertigen lassen, was aber sicherlich einiges kosten wird.
Ich habe meine Fräser immer aus HSS gedreht und dann die Schneiden mit einem Dremel hinein geschliffen.
how much u sell that mold... but i want 0.31 cal...
Why did the reamer wobbled like crazy when you withdraw?
nice work!
Looks great.
darauf hätt ich kommen können :)
wo kann man sich einen entsprechenden fräskopf fertigen lassen, oder wäre es viel wirtschaftlicher einfach aus einer etwas leichteren kokille die fettrillen rauszufräsen ?
I like to buy a mold... how can I get a mold
Here's a question for you. Why would you go through all the trouble of making a mold that you can buy for $25? I mean you did a really good job but I think I'd rather spend the time casting bullets or reloading.
If you saw his sprue plate you would realize it's for automatic casting machine. You can't just buy a bold for $25 for it. Also the aluminum that cheap Lee uses is not as good as better molds like NOE uses.
Um, they dont make it in the shape he wants. For example, they make a 2R mold for 9mm but why not the same shape in .401?
Realy nice! Good job =)
Excellent work! I would love a two-cavity set of these in .355 147gr RN :)
The music! Hahahaha awesome
How deep do you need for vent lines to be?
How is your bullet lubricated with no grease grooves ?
thats what i was thinking
powder coat
I think the bullet is intended to be powder coated
Do you have website? Price mold 5.52mm?
How to purchase?
Great job,SUPER!! So ho much one mold cost?
I would like to order a set of molds from you... let me know what information you need from me and cost of course.
No music please, we do like the sound of tools. Not this horrible music
How do we order from him ,I'd like a set of moulds from you.?
bf20 vario gell?!
Sehr schöne Arbeit!
Will you make some for people
I want to buy how to contact?
@ 2:47 Did you buy or make that cutting tool?
+ownedkapoo Hi, i made it.
Watch my other videos to see the process.
voce saberia copiar projrtil de carabina de ar
.177" please 🤘
WOWED
Nossa muito top,,