I’ve been putting this off because I knew it was gonna be a pain in the ass. I have to replace my injectors so I guess I’ll do them both at the same time. I like realistic videos like yours because it shows how to overcome the challenges and not glass over them.
Thanks! I'm helping my neighbor change his gasket. We did the exact same things you did. The problem was lifting the rear of the valve cover up to remove it. That dang plastic harness holder. My neighbor was getting mad😊.Your video help us out👍
I am literally in the exact same place as you. Wanted to get those 3 done during the Pandemic time off. Haven't because of the 1000 other projects I needed to get done. And am now at a week or so before work fires back up.
I feel ya. :P You're in luck though. The second video in this series went up today! th-cam.com/video/-fj-tmkb0WQ/w-d-xo.html I hope it helps you. I'm in the process of editing the final video now, where I actually get the oilpan and rear main done.
Rear main too .. ? Wow. I'm about to start my 2nd tj, so much goop. This will be my... 5th straight 6 jeep cover job. Only had 1 that needed a new rear seal, a couple years later needed crank and main bearings too. Usually just the cover leaking making it look like it's every where. Better than the wife's leaky jku, oil cooler o rings, pull intake manifold 😢
Good video, I think I change the harness before, so if I take the valve cover off its much easier. The change the tires, they chance everything of a Jeep, why not self modifed the plastic harness?
No engine degreaser recipe in the description as promised. Would also help to know what year your TJ is as there were 3 different versions of the 4.0L during the 97-06 model run all with different piping, wiring and bolt patterns.
Yea, I dont know why I didnt do that. It looked like it'd be a pain to get to, but in the end, I fought it every step of the way, so was it worth not taking the time? Not sure.
Those plastic CCV elbows are a pain. Not sure why some company hasn't produced an aluminum or stainless elbow as a replacement. Would be a vast improvement.
FSM calls for disconnecting everything from the driver side and laying the entire harness over to the passenger to get that plastic harness cover out of the way. I got on YT to see if I REALLY have to disconnect all that stuff and though you did get it done without it, it's a different flavor of suck. I just hate separating connectors that have bathed in engine heat and probably haven't been touched for 17 years...let alone 15+ of them that comprise the majority of the engine control harness.
@@SWBCrawler when I eventually get around to doing mine I think I'm gonna do it your way. I'm nothing special for having an FSM, I just found a digital copy on the internet.
Well, when I installed it, i put it right-side-up like all the others. I cant be certain of it was actually upside down, or if it just popped off when I pulled out the VC. It sure was sitting right on the block like it was installed on the wrong side of the cover when it went in.
![[LIVE] : ONE ลุมพินี 84 วันนี้!! คู่เอก "ก้องศึก vs เมืองไทย"](http://i.ytimg.com/vi/3kuzsAIDf1c/mqdefault.jpg)
Just did mine. Popped the wiring loom out of the plastic bridge, then removed the bridge which made life MUCH easier
Same!
I’ve been putting this off because I knew it was gonna be a pain in the ass. I have to replace my injectors so I guess I’ll do them both at the same time. I like realistic videos like yours because it shows how to overcome the challenges and not glass over them.
Thanks! I try to make videos that show the struggle, not just the money shot. ;) I'm glad you appreciate that!
Thanks!
I'm helping my neighbor change his gasket. We did the exact same things you did. The problem was lifting the rear of the valve cover up to remove it. That dang plastic harness holder. My neighbor was getting mad😊.Your video help us out👍
I'm so glad it helped you! That dang harness was the most frustrating part of the whole job!
Nothing wrong with being thorough.
Just about up to my elbows in grease right now. Let the healing begin
lol yep! very dirty job!
I am literally in the exact same place as you. Wanted to get those 3 done during the Pandemic time off. Haven't because of the 1000 other projects I needed to get done. And am now at a week or so before work fires back up.
I feel ya. :P You're in luck though. The second video in this series went up today! th-cam.com/video/-fj-tmkb0WQ/w-d-xo.html I hope it helps you. I'm in the process of editing the final video now, where I actually get the oilpan and rear main done.
That back bolt sure looks fun. Nice job man.
Ohhhh quite the opposite.. Not fun at all. :P Thanks!
Rear main too .. ? Wow. I'm about to start my 2nd tj, so much goop. This will be my... 5th straight 6 jeep cover job. Only had 1 that needed a new rear seal, a couple years later needed crank and main bearings too.
Usually just the cover leaking making it look like it's every where.
Better than the wife's leaky jku, oil cooler o rings, pull intake manifold 😢
yea. when i did this i wasn't sure if the rear main needed it. so i did it just for good measure. i think it was just the cover too.
And you put the filthy cover back on?
Good video, I think I change the harness before, so if I take the valve cover off its much easier. The change the tires, they chance everything of a Jeep, why not self modifed the plastic harness?
The harness/channel behind the valve cover? I didnt want to risk messing up the harness.
No engine degreaser recipe in the description as promised.
Would also help to know what year your TJ is as there were 3 different versions of the 4.0L during the 97-06 model run all with different piping, wiring and bolt patterns.
sorry about that! degreaser information is here:
th-cam.com/video/f6-w7egOKG0/w-d-xo.html. and it’s an 05. thanks for watching!
I found it much easier to just remove the plastic wire cover in the back before taking the valve cover off and putting it back on after reinstall
Yea, I dont know why I didnt do that. It looked like it'd be a pain to get to, but in the end, I fought it every step of the way, so was it worth not taking the time? Not sure.
Those plastic CCV elbows are a pain. Not sure why some company hasn't produced an aluminum or stainless elbow as a replacement. Would be a vast improvement.
Yea! No doubt! Thanks for watching!
FSM calls for disconnecting everything from the driver side and laying the entire harness over to the passenger to get that plastic harness cover out of the way. I got on YT to see if I REALLY have to disconnect all that stuff and though you did get it done without it, it's a different flavor of suck. I just hate separating connectors that have bathed in engine heat and probably haven't been touched for 17 years...let alone 15+ of them that comprise the majority of the engine control harness.
yeeeaaa. i didn’t have an fsm to follow. disconnecting everything might have been worth it.. but i managed
@@SWBCrawler when I eventually get around to doing mine I think I'm gonna do it your way. I'm nothing special for having an FSM, I just found a digital copy on the internet.
@@freedomin4low344 good luck!
What happened with the rear most grommet? Was it installed upside down like you thought, or was it correct?
Well, when I installed it, i put it right-side-up like all the others. I cant be certain of it was actually upside down, or if it just popped off when I pulled out the VC. It sure was sitting right on the block like it was installed on the wrong side of the cover when it went in.
Good video sir. Thank you.
Thanks! and thanks for watching!
You still have that clamp on the hose?
I mean... Maybe?
awesome video!
Thanks!
no profit what a bad video
I'm sorry.. what were you looking for?
@@SWBCrawler Don't be sorry....he's a D-bag.
@@billiebuckamer8189 I got that feeling. ;)