One month ago ago I watched video battery low problem only micro. Ke pin no 5 pr 3.7 volt I replied but I m watching Full video fully helpful votes thank u so much big sir 👍🏻🙏🏻
Khanna sar aapko tahe Dil se shukriya meherbani aapki Jo ham Jaise logon Ko guide kar rahe hain aapki video se bahut Sahara milta hai jiski badaulat hamen kam karne mein aasani Hoti hai sar aap se ummid hai ki aap hamen aise hi guide karte rahiye shukriya aapka din Shubh rahe
कानहा जी नमस्कार, आपका विडियो देखा बहुत बढ़िया तरिके से समझाया है आपने। मेरी दुविधा है कि मेरे माइक्रोटेक sine wave 875 e2 इन्वर्टर के माइक्रोकंट्रोलर HA3089-I/SP के पिनो का विवरण नहीं मिल रहा है। आपका आभारी हूंगा आप कृपया यह विवरण उपलब्ध करा दें। आपके उत्तर की प्रतीक्षा रहेगी। धन्यवाद। संजीव गुप्ता
Aapke bahut helpful video hai " Low battery issue koi bolata hai microcontroller pin number 5 koi bolega pin no 10 Mujhe ek problem salu nahin ho raha aap iske answer dijiye sar .. ✍️
Sir mere pas bhi ek 925e2+ inverter aaya hai us inverter ke micro pin no 5 pe 3.90 v hai lakin cusyomer ka kehna hai ki charging nahi ho rahi hai maine 8/12 ki battery lagake check kiya to charging ampere 3-4 tak aa raha hai lakin ch full hone ke baad 100w ka bulb khali 10 minute hi chal raha hai kya battery 100% charge na hoke is situation me battery kam charge ho sakti hai kya ya koi dusra problem hai please help me sir
Sir 3.7 v set kaise hota hai koi setting point to isme nahi hai.wo bhi batane ka kast kare.mere inverter mai 3.3 v aa raha hai battery ka pani sukha de raha hai . Charging karte ja raha hai.
I have seen the video and views offered by many people. It is very good that you have traced the voltage sensing circuit in the board. But you have missed one resistor R34. Actually, R56 (51K) and R34 (20K) has formed potential devider circuit. With 12V Supply, voltage across R34 of this potential devider becomes nearly 3.2V, not 3.7V. Practical test also shows it. If supply voltage is 13.6V, then only voltage in pin 5 of microprocessor will be 3.7V. Please comment.🎉
Sir smd microteck inverter ma battery low ka problum aaya or mana R56 resistance open ho gaya .r56 change kar deya or fir battery charging nahai ho raha.output 05 1 ampar aa raha ha.kya karu sir
Sare Componate sahi hai sar fir bhi volt nhi ban rhaa hai kya karan ho skta hai 5 number pin ko cutkarke volt chake kro to aa rahe hai or connect karne par nhi aa rahe charging sahi kar rhaa hai on karte hi low battery de rhaa hai
Bhaiya mere inverter se high volt AC 270 kaaran nikal rahi hai to iska kya problem hai kaun si kit humko change karna hai... Meri inverter ki model hai microtek 1250.. please help me
Namaskar Sar Sar Ek Microtek solar inverter Transformer ki supply circuit per Lag Rahi to log Baithe the Kha Raha hai aur Transformer ki supply Hata de rahe pura system Sahi kam karta kam kar raha hai
Bahut hi acchi Tarah Se explain karte hain aap
Apka video bahut achha hota h full information ..... My name RAAZ From bihar
One month ago ago I watched video battery low problem only micro. Ke pin no 5 pr 3.7 volt I replied but I m watching Full video fully helpful votes thank u so much big sir 👍🏻🙏🏻
Thank you sir ji achchha laga samjha me bhi aaya hai aap ke jaisa koi samjha hee nahi payega 👌👌👌
सर जी मै आपकी हर वीडियो देख कर बहुत कुछ सीख रहा हूं दिल से शुक्रिया
Thanks sir. Mai West Bengal se ap ka fan ho gaya sir.ap ka har video flow karta hu.mai banali hu Mera Hindi itna achha nehi hai
thank you so much sir aaj mai aapka ye video dekh kar ek set mai vi ok kiya hu
Good sir ji bhot hi ache trike se samjhaya apne
Khanna sar aapko tahe Dil se shukriya meherbani aapki Jo ham Jaise logon Ko guide kar rahe hain aapki video se bahut Sahara milta hai jiski badaulat hamen kam karne mein aasani Hoti hai sar aap se ummid hai ki aap hamen aise hi guide karte rahiye shukriya aapka din Shubh rahe
,
आप का बीडियो बहुत ही अच्छा है
सर मै सहारनपुर जिले से हूं
सर मै आपकी आने वाली वीडियो का बहुत वैट करता हूं दिल से शुक्रिया आपका
Good
Thanks sir
सर आपका दिल से शुक्रिया काम सिखाने के लिए
Jo aapane bataya humne vahi Kiya hamara inverter sahi ho gaya sar
Wah kya samjhate ho sir thankq so much 🙏🙏
Bahut Accha video bnaye sir thanks
Very useful information ❤
Very nice sir ji
कानहा जी नमस्कार,
आपका विडियो देखा बहुत बढ़िया तरिके से समझाया है आपने। मेरी दुविधा है कि मेरे माइक्रोटेक sine wave 875 e2 इन्वर्टर के माइक्रोकंट्रोलर HA3089-I/SP के पिनो का विवरण नहीं मिल रहा है। आपका आभारी हूंगा आप कृपया यह विवरण उपलब्ध करा दें। आपके उत्तर की प्रतीक्षा रहेगी।
धन्यवाद।
संजीव गुप्ता
Good tiching karte hai 👌👍👌👌👌
Sir I will never forget to u.... 🙏 Tq soo much
सर, आप ऐसा एक विडियो बनाए, बिल्कुल सुरु से, inverter कैसे काम करता है ,कार्य प्रणाली बताए step by step.
धन्यवाद।
Thanks sri mujhe bahut help
Aapke bahut helpful video hai "
Low battery issue koi bolata hai microcontroller pin number 5 koi bolega pin no 10 Mujhe ek problem salu nahin ho raha aap iske answer dijiye sar .. ✍️
Aapke video se bahut jaankari milti hai. Thank you.. V3 v4 v5 difference kya hai. Ek dusre mei lag sakte hai?. Apke pass smd pcb available kab hoga.
Yes sir microtek ki new modle pcb bi par bi banayey. Vedio 👍👍
Ok
sir ji new kit pe bhi vedio bnye thanku for information
Sir apne in Vetter ka bhagwan he thank you sir
बहोत बढिया सर
Sir ji Charing 2 amp aa rhi h
Kya fult
Nice sir ji ap jharkhand se ho
Thanks sir for sharing this information
M.M.M Mufeeth
Microtek inventor model number 2350 24V SW how can solve over load problem?
From Srilanka
Luminous inventor battery backup can't buy in here what's the reason
Modern number 1050
thank you❤🌹🙏 sir
You are great sir
ok bhai ji bahùt shi batya aap ne
Sir mere pas bhi ek 925e2+ inverter aaya hai us inverter ke micro pin no 5 pe 3.90 v hai lakin cusyomer ka kehna hai ki charging nahi ho rahi hai maine 8/12 ki battery lagake check kiya to charging ampere 3-4 tak aa raha hai lakin ch full hone ke baad 100w ka bulb khali 10 minute hi chal raha hai kya battery 100% charge na hoke is situation me battery kam charge ho sakti hai kya ya koi dusra problem hai please help me sir
Very very good suluation
Nice video sir mosfet ok hai 1second ke bad overload mai chla jata hai kya fault honga
Sir hot air gun ke lya bhi ek video bna dejay
Sir ek inwater hai jo continue beep kr rha hai aur led sabhi glow kr rha hai isme kya problem ho sakta hai
Very nice.sir how set in this board.
mcu bahar se mil jata h kya
3 point 7 word remote per Aane chahie ya charging Mod per
सर आप वीडियो रोजाना दो
Microtek smd bord drive section me kon .kon se jiner lage hai
Sir 3.7 v set kaise hota hai koi setting point to isme nahi hai.wo bhi batane ka kast kare.mere inverter mai 3.3 v aa raha hai battery ka pani sukha de raha hai . Charging karte ja raha hai.
Sir luminous inverter lena 900 va ka kaun sa model lein?
Sukem par video banayiye sir
Sir is model me transformer se fd voltage kitana aata hai
Sir microtek jumbo model ki video banayey
Minus wala wire kaha lagega janab
V4 Microtek me charging amp kam jeyada kaha se huta sir
Nice video thank you sir
शुक्रिया सर् जी
Thank you 🙏
This video very helpful
Tiker ke kitne volt hote h
Sir Microtek eb 1100 me over change problem hai microcontroller pin5 3.37 volt dikha rahe hai divode rejester 51k ok hai kya kare
I have seen the video and views offered by many people. It is very good that you have traced the voltage sensing circuit in the board. But you have missed one resistor R34. Actually, R56 (51K) and R34 (20K) has formed potential devider circuit. With 12V Supply, voltage across R34 of this potential devider becomes nearly 3.2V, not 3.7V. Practical test also shows it. If supply voltage is 13.6V, then only voltage in pin 5 of microprocessor will be 3.7V.
Please comment.🎉
Microtek v8 pcb pr video jrur bnao ji
Dive ok inveter mai bhi ok.mains dene ke but mosfeet jol jata,hai q.
Good job sir ji
Sir please v4 and v5 fuse blown par video baniye
Thank. You
sar agar pin number 5 per voltage kam ya jyada ho jaaye to use kaise set kra uska preset kahan par hota hai
Microtek v5 me charge led biling nahi kar rah hai aur battery charge bi nahi ho raha hai video banaye
Sr pin 5 par voltage Kam ya jada kese kare
Thank you
Sir smd microteck inverter ma battery low ka problum aaya or mana R56 resistance open ho gaya .r56 change kar deya or fir battery charging nahai ho raha.output 05 1 ampar aa raha ha.kya karu sir
Mujhe pasand aaya
Good sir ji
Sir smd pin 5 pr 3.4 v h fir bi battery low aa rha h
Luminous Eco watt 1 KV mens dene per overload aur battery low ka signal de kha Raha hai kya dikkat ho sakti hai sar
Thanks sir,
Thank you sir ji
Thanks Sir
Microtek solar inverter ke upar video banaiye. Solar se charging nahi ho raha hai.
Sare Componate sahi hai sar fir bhi volt nhi ban rhaa hai kya karan ho skta hai 5 number pin ko cutkarke volt chake kro to aa rahe hai or connect karne par nhi aa rahe charging sahi kar rhaa hai on karte hi low battery de rhaa hai
धन्यवाद
सर आप कहा से हो
Sar Mera 1000eba hai usme daibod aur ragistens bahut chote chote Lage usko kaise Cheng kare aur mera mosped bar bar fat ja raha hai
Bhaiya mere inverter se high volt AC 270 kaaran nikal rahi hai to iska kya problem hai kaun si kit humko change karna hai... Meri inverter ki model hai microtek 1250.. please help me
Sir me up se Shikohabad se hu Microtek V5 m mans nhi a rahi h ic k pin number 4 pr 1.7 vo a rhe h fir bhi mans nahi arhi h please sir help
Sir spare available with you?
Nice 👍👍
Nice work
Nice video sir
सर IC 83202 कहा से और कितने का मिलेगा
Sir ji mens sow ho raha hai bat charjing led aur amp nahi aaraha hai
👍👍👍👍👍♥️♥️♥️♥️🇮🇳🇮🇳🇮🇳
V7 card m main Dene par kantinu veep aati h or charging led nhi jalti h s
Lm 324 smd ka kya kam hai
सर नमस्कार माइक्रोटेक का इन्वर्टर है ए.सी वोल्टेज कम निकालना है इसका क्या फंड हो सकता है मैं लालू इलेक्ट्रीशियन हूं
Sar SMD kit mein battery low ka aur I charging ka bataya tha aapane UPS mode Man Mein Tha
Good sir
❤❤❤❤❤
माइक्रोटेक 1050 ऑन करते ही बैटरी लो मैं जा रहा है ❤
Namaskar Sar Sar Ek Microtek solar inverter Transformer ki supply circuit per Lag Rahi to log Baithe the Kha Raha hai aur Transformer ki supply Hata de rahe pura system Sahi kam karta kam kar raha hai
Sar v5 microtek obarlod the nahin horaha hai
V5
Overload de raha h ya nahi kya puchna chahte ho
Rile par Kaha Kaha saflai jata video banai sir
Thanks