Protect your 18650 battery by this
ฝัง
- เผยแพร่เมื่อ 17 ธ.ค. 2020
- In this video, i want to show you how i Protect my 18650 battery by this 1S 3.7V 3A 18650 Battery Protection module
Music:
Blue Skies - Free on TH-cam
Carefree - Kevin MacLeod
Carefree by Kevin MacLeod is licensed under a Creative Commons Attribution license (creativecommons.org/licenses/...)
Source: incompetech.com/music/royalty-...
Artist: incompetech.com/ - วิทยาศาสตร์และเทคโนโลยี
Hi, where will be the charging terminal for this set up to charge the battery ? Is it the input terminal as well?
Hello friend! Thanks for the video, nice work! I have a question, what cable do you use, how much is AWG?
Hello! I added PCB protection board to a 18650 battery but it won't charge.. do you know what may be the reason?
Thanks for sharing.
Tq for this infomative video boss
Hello, can four cell phone batteries be charged in series with this bms, or what should I use to charge it?...
Is it possible, 1 BMS 1S for 2 or more batteries? Thanks.
Question: how to wire when on the same time: charging and a load connected????
Hi, the TP4056 module has ( DW01A and 8205A) can we just include multiple 8205A's to TP4056 and eliminate an additional cost for bms in a battery management system.
no. The module you're referring to is for a single cell only. If you wish to connect multiple cells at the same time, you will need a multi-cell module that has cell balancing.
Very useful
Can you use these under a BMS module that manages a group of 6 of them or so for example, or will it interfere with the larger bms?
I was wondering the same thing. I bought a large pack of lipo batteries (the flat pouch like ones you use in rc drones and cars) and they all have pre-installed bms boards. They are good boards with a temperature sensor connection and I have been looking into this exact question wondering if I could make a battery pack with them in parallel as I would think it would be the same as putting a fuse on 18650 cells.
Nice product
Hello sir, can i use that 1s 3a bms on 3 pcs. of 18650 2600mah battery?..
Fantastic idea
Thanks for pupport bro✌💞
Very interrasting 👍.
thanks !
can we connect it in series?
Here before the "who got recommended comments"
I got recommended this
can we make a pack with these?
So nice
That Right...!!!
Can this act / replace a tp4056?
That's cool!
Thanks for pupport bro
Hi shouldn’t the bms allow charging up to 4.2v before shutting down?
Depends on the battery and BMS model
Bossing pano yung apat n battery nka parallel alen po pwede..
What volt input?
Awesome 🤩 Idea
Thanks for pupport bro💞❤❤❤
If we want to connect it with a solar 3W 6V 3A then
Can it (1s BMS) be used in multiple 18650s battery connected in parallel (ie power bank)?
No
@@thevlog3653 how about only 2x 18650?
Yes get an high amp one like 5amp
3:13 What do you mean battery recovers itself? turning a connected device on and off might be damaging....!!
Power consumption, the power is too low the protection board will be powered off, the power off process is in a state of no power consumption, the power will be increased to cause the protection board to think that the power is enough, so it starts to open the power supply again
Si uso una tarjeta BMS puedo cargar la batería con un cargador de 5V
Can I make 1s 10p?
Master, how can I do 2s bms in parallel connection, please reply, thank you
Can you describe it in more detail?
@@CreativeAndDuck hey I have a question about this protection, I have a 4cells in parallel and then in serie (total voltage is 12.6v 25000mAh )do I need to put this protection on each cell?
can we use 1s bms in series connection with other same 1s bms?
Yes...should of more ampere (4056 is 1Amp)
Can this 1s bms be used in 3 18650 in parallel?
It could, so long as it's parallel that is. You should try to limit how many you put in parallel though as when one fails the others will start putting power into the failed one and start a fire or explode... that's why you use those nickle fused sheets (after too much current passes into a dead cell it breaks the fuse to avoid explosions and fire). Still is somewhat dangerous; I recommend doing thorough research into the topic regardless to avoid issues and injuries as well as to minimize potential hazards.
How to shop ing and links and send me please
Input voltage?
Can I charge with 5v usb charger?
Yes you should be able to. 👍
Can you make series battery demonstration with this tiny bums board?
I used a bms on a tp 4056 charger and it works well.
Can Bms alone charge without Tp4056 with dc source of 6-12V?
Can i use 1s bms for 2 batterys
You can but the charging time will be more. If that is not a problem you can. for one battery if it takes one hour then it might take two hours as there is a max limit of 1A.
Hi, greetings and salutations from Mexico. This video was very interesting for me and the question I want to ask is as follow: I need to replace the batteries of an Emergency lamp which it's always connected to the electricity and the batteries start working when the electricity is cut off and the light is turned on. . Could the circuit showing here be good to protect any damage ?, I mean that the battery may explode due to continous connection to the electricy. I appreciate your comments, and thank you very much in advance.
this cercuit model code no?
you can crank that up to 10KV and it wouldn't matter, as you pushing 0.00A
No amperage, no power
Not true at all. Something has to detect that the voltage is too high, and that something would have to be able to withstand 10KV. It could also arc across solder points. That board is not designed to withstand 10,000 volts.
Can this be connected to charge 2s, 7.2/8.4v?
You can buy a 2s BMS, you can not use this one for that purpose. If i'm not wrong yhere is 1s(like this one) 2s and 3s BMS, you can buy them on aliexpress relatively cheap
Thank you.