hey bro.. My busa was running fine but started to take jerks as if fuel supply isn't proper.. I pulled the fuel injectors n checked them they were clean and good.. After I placed them back the bike is not starting properly and dies while running as if no fuel is being supplied.. what do you suggest..? Should I check the spark coils as well..?
My 05 Hayabusa rectifier melted the end connection on my bike and I can't tell which wire goes where so I can rewire it. Any suggestions or pics of how wiring goes?
As long you have C00 that's good. Dash at the bottom is a matter of calibration of TPS. You can calibrate it yourself and its quite easy, check my other vid for that prcedure. Does your bike run poor? If it doesn't then no reason to worry.
I tried to do it on my 2002 Hayabusa and i couldn't make the dash go down from the top position even when i made the screws more loose and moved the sensor a bit harder
Could be many reasons. Balancing the throttle bodies could help. People say Tps calirtation could help.Ofteen backfiring is caused by bad plug or bad coil. In my case it used to backfire cause fuel system was screwed by dirt.
![[LIVE] : ONE ลุมพินี 73 วันนี้!! คู่เอก "วรพล vs พันฤทธิ์"](http://i.ytimg.com/vi/rrOljlqse3A/mqdefault.jpg)
Thanks so much for this video! Made it so easy to sort my TPS 👍🏻
I just did this on my 2000 busa and this was very helpful!!!
Great that somebody benefits from it
Brilliant man love watching and learning thank ❤️👀👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍
hey bro..
My busa was running fine but started to take jerks as if fuel supply isn't proper..
I pulled the fuel injectors n checked them they were clean and good..
After I placed them back the bike is not starting properly and dies while running as if no fuel is being supplied..
what do you suggest..?
Should I check the spark coils as well..?
My 05 Hayabusa rectifier melted the end connection on my bike and I can't tell which wire goes where so I can rewire it. Any suggestions or pics of how wiring goes?
is this for rough idleling?
What if the dash falls to the bottom when I let off the throttle? But then sits back in the middle after falling
hi my diagnostic plug is 4 pin and i want put a gear indicator i dont know what to do in the instalation guide they talk abour a 6pin plug
Cześć, super filmiki❤. Pytanie jak ustawić TPS jak mam założony inny licznik (motogadget) i nie mam oryginalnego? 😊
Put my 03 busa in dealer mode and got the little dash on the bottom _C but as soon as I started it went to the center -C ?
As long you have C00 that's good. Dash at the bottom is a matter of calibration of TPS. You can calibrate it yourself and its quite easy, check my other vid for that prcedure. Does your bike run poor? If it doesn't then no reason to worry.
I tried to do it on my 2002 Hayabusa and i couldn't make the dash go down from the top position even when i made the screws more loose and moved the sensor a bit harder
Hello there last get this straight in dealer key on engine of -COO running the same or on top?
Plazas experience in details
It won't start to warm up and I can't get the dash to stay on middle the dash moved to top or bottom
for check mode diagnosa please
i have a 01 busa that runs rich. and pops. . wat you think
Could be many reasons. Balancing the throttle bodies could help. People say Tps calirtation could help.Ofteen backfiring is caused by bad plug or bad coil. In my case it used to backfire cause fuel system was screwed by dirt.
My Hayabusa shows C00 with upper dash and won’t start
I need some help, IAP location, can any one help me? 2006 hayabusa, thanks
You still need help?
@@blackhayabusa1668 yes ser
hello give me the hole.name
iap