The coilovers were from ebay, around £250: www.ebay.co.uk/itm/404474634372?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=dzpq5d_0sou&sssrc=4429486&ssuid=hMYVXo0ZRfi&var=&widget_ver=artemis&media=COPY
Appreciate the feeback, thank you! These are the ones i got, theyve been good so far, message me on instagram if you want any specific pics or help with anything! www.ebay.co.uk/itm/404474634372?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=dzpq5d_0sou&sssrc=4429486&ssuid=hMYVXo0ZRfi&var=&widget_ver=artemis&media=COPY
I managed to remove everytiing at the back apart from the anti-rollbar is seized, well the hex screw isn't there What size did you use? Maybe I will saw it off and then get a new anti-roll bar
Ah that sucks, I can't recall the size now but I would strongly advise against cutting the roll bar, been there before and it creates a lot of extra hard work 😂 if you can, try a lot of wd40 and apply some heat if you have a blowtorch, i got a cheap one from amazon meant for cooking its perfect for stuck bolts!
@@Negative_enO I managed to remove it with an angle grinder, both installed on the back now. The only issue I have is the coilovers are squeeky! I hand tighted the pre-load, and used the ratchet tool which came with it as a width guide. I didn't touch the rebound adjustment on top, what do you reckon? Add more preload?
@kieranadams2483 i had to set insane preload on mine just to clear the wheels against the spring seats 😂 Squeak could be the top mount though as mine were bad when i got them, had to put a lot of grease on them but been fine since!
just got a gen 6, this is helpful. thanks!
Always happy to help! 😁
Where did you buy it from and how much did it cost
The coilovers were from ebay, around £250:
www.ebay.co.uk/itm/404474634372?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=dzpq5d_0sou&sssrc=4429486&ssuid=hMYVXo0ZRfi&var=&widget_ver=artemis&media=COPY
hey, really appreciate the video it was super helpful but do you have a link to the coiovers as i'm doing research to replace my stock suspension : )
Appreciate the feeback, thank you!
These are the ones i got, theyve been good so far, message me on instagram if you want any specific pics or help with anything!
www.ebay.co.uk/itm/404474634372?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=dzpq5d_0sou&sssrc=4429486&ssuid=hMYVXo0ZRfi&var=&widget_ver=artemis&media=COPY
I managed to remove everytiing at the back apart from the anti-rollbar is seized, well the hex screw isn't there What size did you use? Maybe I will saw it off and then get a new anti-roll bar
Ah that sucks, I can't recall the size now but I would strongly advise against cutting the roll bar, been there before and it creates a lot of extra hard work 😂 if you can, try a lot of wd40 and apply some heat if you have a blowtorch, i got a cheap one from amazon meant for cooking its perfect for stuck bolts!
@@Negative_enO I managed to remove it with an angle grinder, both installed on the back now. The only issue I have is the coilovers are squeeky!
I hand tighted the pre-load, and used the ratchet tool which came with it as a width guide. I didn't touch the rebound adjustment on top, what do you reckon? Add more preload?
@kieranadams2483 i had to set insane preload on mine just to clear the wheels against the spring seats 😂 Squeak could be the top mount though as mine were bad when i got them, had to put a lot of grease on them but been fine since!
If I assume correctly, this is a non Super Strut car right?
Yep thats right, UK spec ST202 😁
Sick car but those rims gotta go
I like them, plus they only cost me £50 I'm not even mad 😂 they're getting a respray soon though!
Some speedline six spoke will do very nicely here