Hey Frank, thank you very much for your video. Ive got the W1070 since 2013 and ive had blurring and flickering so badly. So I decided to give it a try and clean the whole projector. It was definetly a mess but after all steps especially the sensor and colorwheel cleaning, it works like day one. Iam so happy and thank you so much for this helpful video. Best regards
W1070 still intermittently shut down with red Lamp and Temp led after hours, that is after I replaced the stock 3800 hr lamp (original owner) and color wheel with new ones from purelandsupply. The new color wheel can turn additional 1/8 turn freely when I manually turn it, while the old one stops turning immediately. The color wheel sensor looks as clean as new, no brown smudged like in your video, but I cleaned it anyway, along with all 4 fans. The only improvement after new parts seem it shuts down less frequently, like sometimes it can last 4 hrs without problem, but still shuts down every other day after 2 hrs, while the old lamp and color wheel shutdown after an hour everyday. Both case can turn back on for at least an additional hour after shutdown. I did zero the lamp hour. I suspect the new color wheel is still not good enough, especially there is a tiny scratch on the color pattern, and it does not turn more freely maybe an additional full 180 degree when I manually turn, Or maybe the new color wheel has been unused for so long so it needs time to break in, so the friction from its bearing overheated the projector from time to time? However the new parts does improves a lot on the image depth and has more vibrant color.
Lamp and temp LED mean a fan is a problem or dust is built up. The color wheel is okay. I can't say which fan, but if you check the service menu, it will say which fan is erroring. also make sure you didnt turn the exhaust fan the wrong way. It should blow out. It is easy to reverse it without knowing. Your issue is thermal related. Lamp led means, lamp had to turn off or cant turn on. When you see it with the temp LED , that almost always means a fan.
Hey Frank, I'm looking for some input. I've got a BenQ W710ST that the lamp wont ignite. It turns on and after about 10 seconds a fan kicks on, the lamp light goes solid red, and the power button flashes orange. No light comes from the lense. So far I've thrown a couple parts at it, I replaced the power supply & the ballast. I've also tried cleaning the sensor on the color wheel. Still not fixed. Any ideas what I should try checking? Thanks.
What led you to the power supply and ballast? Was the PFC voltage low/non existent? What about the ballast control lines? What did you measure there that led you to the ballast? I'm also guessing you confirmed the color wheel index pulse is correct? My usual process is confirm/verify the voltages and then track down which component is causing the wrong voltages. What about a new lamp? Did you try a known good lamp? In my experience lamps are 90% of the issues then color wheels(for dlp). I'd make sure you have a good lamp and start over and make sure that thenl color wheel is spinning properly. Then work your way out. Good lamp and checking voltages is your best bet.
@@FixitFrank The power supply had a brown area on the bottom that looked burned so I replaced it. I knew the entire lamp assembly was new, so I just thought logically that it must be the ballast that was bad. I didn't measure anything, mostly cause I'm not sure what to measure. I have a good multimeter though if I need to check any voltages. Can I check a pulse with multimeter at all or do I need to get a scope?
If your meter has HZ/frequency you could. I also have a few videos on troubleshooting color wheels without a scope. you might want to watch this first. th-cam.com/video/HC0u08IjAY0/w-d-xo.html
Just a suggestion, to remove nicotine I use a degraser to clean kitchen in Italy it is sold like "chanteclear" I don't know the brand in US but it Is very helpfull for those jobs, just need to spray it on dirty surfaces and it melt nicotine, then wash with normal water and the item is like brand a new!
Thank you so much! Is it this stuff? www.amazon.com/Chanteclair-Sgrassatore-Ecodetergente-Friendly-Degreaser/dp/B00VKODPHK I will be glad to try it. It's honestly been a while since I dealt with nicotine. Back in the day, it was just part of everything. I can think of a few other uses if this is as powerful yet safe for certain surfaces as it seems.
@@FixitFrank Yes Is just this! It Is very powerfull to clean nicotine and other grease dirty. Just One bad side, It has very strong smell not bad, like old soap, but It melts any kind of dirty.
@@FixitFrank I'm from Napoli but my girlfriend is from Denver and now She lives in Salem (OR). Before the covid time I was in US every year, I Hope to return this year :) Where you live in US? I learn my poor english from my girl.
Hey Frank, thank you very much for your Video. I have a BenQ W1400 that shuts down after a short time (~60sec). The Picture is fine though, so its probely not the colour wheel. Anyways, I fully cleaned everything following you example (ALL Fans, Color Wheel and Sensor, everything else) but the problem remains. I noticed that each time I turn it on, the Projector shuts itself of a little faster. So first it says on like 60seconds, then 40, the 20 seconds. There is no error code, the thing just suddenly switches off. The Lamp is old (still the first one I think) but only has maybe ~2500h. I thought it could be a problem with the power supply. The Caps seem fine on the outside but I have no tool to test them.
Thank you very much! That sounds like a lamp issue to me. 2500 hours is more than enough. I would try a new lamp first because without knowing 100% your lamp is good, that may be the root cause. It is also the easiest part to get. If the lamp LED flashes when the projector shuts down, that would be my initial suspicion. Especially if you are running in eco mode. Eco mode runs the lamp at lower power and can cause deposits to build up on the arc points. Unless the lamp is put back into standard mode occasionally for a few hours, those deposits can cause the entire module to fail early. That is what it sort of sounds like. If a new lamp does not solve the issue, then more troubleshooting would be needed, but I really suspect your lamp at this point.
@@FixitFrank I installed a new Lamp but the Problem remains. Also I noticed that I can't turn the projector immediatly on again after it shuts down. I have to wait a Minute or so.
Ho Frank good video..i have a issue image with my benq w1070 they look posterized..do you think it is necessary to clean the color wheel sensor or is it enough to resync the color wheel from the secret menu??tanks for your video
You could try adjusting the settings but I would suspect the wheel is on the way out or if the lamp assembly was replaced recently, I would make sure it has the right IR filter on the front. Make sure that glass has a red tint to it. If not, send it back and get one elsewhere. If the lamp is still the old one, then I would replace the wheel. They are cheap and you will be glad you did.
@@FixitFrank thank you very much.. the lamp Is the original..i will try to open the projector and check the wheel.. i will update you on the results.. hoping i dont need your advice again..and sorry for my bad english
hello my friend, congratulations on your work!! can you help me ? I have a Benq W1070+ which is giving me problems... I bought it used with an Osram lamp with 230 hours of use. It worked for 70 hours and started to make a high-pitched noise, like a hiss or a resonance then a moire on the brightest areas. After disassembly, I identified the noise coming from the color wheel. I then went back up, then did some tests by changing the display frequency, which influenced the noise of the color wheel. I then adjusted the color wheel sync in the hidden menu, which fixed the moire issue but not the noise. Then I wanted to adjust the gamma and everything went out suddenly with a steady green power light and a steady red lamp light. Impossible to restart since, it turns off after a few seconds without the lamp coming on. the wheel a little then stops but no noise. would you have an opinion? thanks in advance. Sorry for Google trad...
Hello! No problem! It sounds like the wheel itself is bad. If the wheel cannot run properly the projector will shut down and flash the lamp LED. They use a small oil-bronze bushing which wears out. I would purchase a replacement wheel. Any ebay/aliexpress wheel is fine. If you like, you can contact the people I use. They are in China. They ship worldwide and take paypal. Gydz@timeprojectorlamp.com is their email. I hope this helps!
@@FixitFrank thank you for your help, I think there is no longer any doubt about the color wheel breakdown. But there is something strange, the projector turns on directly when I plug it in instead of being in standby with orange power indicator. When off, the power indicator remains green with the lamp indicator red. both do not flash and remain fixed... I hope there is not another problem besides the wheel... and I also hope that the timing adjustments I had made before it dies will not prevent the new one from working properly. Your work is impressive and your videos helped me a lot to understand where the problem was coming from so thank you very much!!
Thank you! Make sure the mainboard is lined up with the low voltage pins. That symptom of the two LEDs usually indicates the power pins from the mains supply are not plugged in the way they need to be.
@@FixitFrank Are you talking about the long pins visible when I remove the motherboard? I checked and everything is connected correctly. do you think there is another problem?
The bulb blew on my w1070, i replaced it but now it shuts down a few seconds after the blue benq screen . No time to get to the menu to reset the lamp timer. I see the color wheel spinning but there is some flickering when the lamp timer warning is displayed immediately after the blue benq screen. I would certainly appreciate any thoughts. I think I hear some process try to start up then the lamp shuts off and it goes into shutdown.
@@bjbarns where did you buy the lamp? Sounds like it has the cheap IR filter glass. See if tbe face of the lamp has a red/blue/purplish color tint to it. If not thats probably the issue. If it's kind of greenish or clear it's letting too much infrared light through and it confuses the color wheel sensor.
Hello, awesome video thank you !! I had the same issue, tried to clean everything including the color wheel sensors (which seemed quite good and was spinning well), but still didn’t work with the flashing colors at the end before shutting down, with the red lamp led up. I think I will have to replace de color wheel. Do you know if there is a specific serial number for it ? And should I replace de small chip that goes with the color wheel ? Thank you again !!
Hi Shino, If you replaced the lamp assembly recently, that might be a cause. The lens on the front can have the wrong coating and let too much IR light through and it will cause the wheel to go nuts. If that is case, you want to return the lamp and buy it elsewhere. Amazon sellers are notorious for this. Otherwise, if the lamp assembly is OEM or good quality, and the wheel is still the original, then replacing the wheel is your best option. There is no special number for it and the sensor can be left alone. Just order a W1070 color wheel from Ebay or contact Time Electronics (who I use). Gydz@timeprojectorlamp.com
I just bought a new OEM lamp from Amazon so I guess the issue is the color wheel, I’ll try to get it replaced Thank you a lot ! You are really saving me with your videos and quick answers
@@FixitFrank Ah sorry, it might not be an OEM then, I wrongly used that word, but it has the same serial number (OSRAM P-VIP 240/0.8 E20.9N) I bought it from France though, the seller’s name is dse.one, but it seems legitimate to me Before buying another color wheel I’ll try giving another cleaning, and try to blow some potential dust in the black box that supports the color wheel, maybe I didn’t do it well the first time…
ahh, Understood! That lamp will be fine. I was worried you replaced the entire housing with an amazon product. Just the lamp (since it is Osram) is perfect. You can try adjusting the color wheel index setting in the menu as well. Press menu, then press source and enter at the same time. USe the arrows to navigate to find the index setting and adjust that to see if it helps. write down the original number so you can go back to it if the adjustment does not help.
Hi, I have a benQ w1400 that had colour wheel issues - flickering etc. i replaced the colour wheel and now the projector is acting like it cant detect a lamp. i turn it on, it makes the noise of the wheel (freely) spinning up multiple times then stops, then the lamp ref flashing light turns on. if you take the lamp out and run the projector with no lamp this is the behaviour you would expect, but it does it lamp in or out. i have made sure the button that closes the case is pressed down, i cant see any other sensor areas, i replaced the lamp completely, i put the original colour wheel back in (that was spinning up but glitchy picture) and its doing the same. i replaced the ballast!! still the same! i also replaced the optical detector on the wheel. prior to me installing the new wheel it was booting up and lighting, now it seems to think there is no lamp in the chamber! the lamp install seems overly simple. one screw holds it in, and a 2 pin plug. anyone have any ideas? this is driving me nuts!!
Just came across your channel! Have you ever come across an odd problem with the W1070, where it'll shut off after an hour of use? A relative is having this issue with there's where after an hour, it'll shut off, and it can be restarted within 2-3 minutes of letting it sit.
Do me a favor and ask them to give you the led flashes when it shuts down. If there is a failure, it will flash the lamp LED or Temp LED. If its just a red power led, that is not indicating an error. That is normal operation. They may want to see if someone set a shutdown timer in the menu. You can set these to turn off after a period of time. A factory reset may clear that setting if they are not sure where it is. But only if none of the other LEDs are indicating an error. I would expect to see a temp or lamp error if there is an actual problem.
@@FixitFrank I just checked, they're telling me the power LED flashes red before it shuts down. They said it's been awhile since they used it, but that's what they recall.
@@FixitFrank Hey Frank! After looking at it in person, it seems like the lamp is bad? The projector powers on, and the lamp light is just a solid red. The fans do come on and spin, like its running but there just isn't any picture. But it did stay running for an hour-ish without shutting down.
Hi Frank. Thanks a lot for your videos, they are absolutely great! I have a Benq W1070 that developed a bad case of dust after I changed the lamp and cleaned the projector it with a vacuum cleaner (bad idea it turns out). You can see it here:
My question: can I just blow some air inside the “inspection cover” of the optical assembly, as you did in your video “BenQ W1080ST DLP Projector Cleaning / Service P2” (min 10:55) or do I have to take the whole optical block apart (or send it to the repair shop)??? Thanks a bunch!
@@alexolazabal4184 Id try it through the inspection port. Worse case, look up one of my DMD replacement videos. Its really not that bad to take out the DMD, but you may be able to get it clean through that hole.
I got rid of the dust, but when I started it again it became very noisy 😨. Within 5 minutes of being on, the temperature jumps from 265 to 380, and the fans go from 2400 to 3700 rpm. It sounds like the Benq is about to take off or explode, so I turn it off!!!
I face a faulty one of these at least once a week. I prefer the 1070+ model. It has 200 extra lumen and has both horizontal and vertical keystone as opposed to 1070's only vertical. To get rid of nicotine this is the best: Amberclens Ambersil Anti Static Foaming Cleaner 400ml
Hello Frank, hello friends. after viewing this video i bought a used 1070 too, bc looks like it is easy to maintain the projetor. Unfortunately it has a problem, because after a few minutes use with perfect picture the image starts blurring, flickering, discoloration, ... so i believe its a heat issue. I have searched the whole internet, but i could not find a hint what could cause it it. Please help me. Thx R.
Hello, that sounds like a color wheel problem. The symptoms you describe seem to indicate that to me. I'd try cleaning the color wheel sensor and also make sure the bulb has a proper IR block coating. The front glass should be reddish not clear or green. If it's not reddish or purple tinted that would be a definite issue.
Hello! Yes, check the power connection between the mainboard and power supply. If the pins are offset to one side, that can happen. It is easy to offset the pins but thankfully it will not damage anything.
I go over it in the video. The power pins. I say not to misalign them during reinstall. It may 'look fine' but clearly something isn't. You didn't do something because it's not working. Go back over your work and reassemble it. Paying extra careful attention to the connector that plugs into the power supply. That's the only thing that could be the cause unless you accidentally damaged the main board somehow.
Hi Frank. What is the fix if the color wheel is slightly misaligned? There is a dark discoloration on the right side of my screen. Also, my housing is falling apart. Is there a way to permanently bypass the button for the bulb cover? My housing won't seal tight enough to hold it down any longer. Thanks.
Probably the light tunnel not the color wheel. They cant be aligned or adjusted but the light tunnel can. I'd search some of my light tunnel vids to get a better idea.
@@FixitFranki found a couple of your light tunnel videos but for the life of me, I cannot find the side to side light tunnel adjustment screw on a W1070. Thoughts?
Sir, I have a w1090 benq. When I press the power button , green blinks a couple of times but bulb does not glow. No temp/lamp error and 2 fans on chasis is working, but the blower attached to lamp case is not working. I opened the projector up, when I manually press the cover sensor, lamp glows for 3-4 seconds and shuts off..when I tried running without lamp, the color wheel is not spinning at all..can you help me pls. Is it a lamp issue ? Or some sensor
If the color wheel is not spinning, I would resolve that first. Be sure the wires are connected and that the glass wheel can spin on its own. They do fail and are sort of cheap to replace. If the color wheel will not spin on its own the lamp will never stay lit.
@@FixitFrank yes sir. Thanks to your videos I could disassemble the color wheel assembly. I guess the connectors (two dots near sensor) was slightly unseated. cleaned and fixed it again. The wheel started spinning. Attached the lamp and It lit up. Thanks indeed for your guidance. Meanwhile cleaned DMD chip too, resolved the occasional vertical lines too. Thank you.God bless!
If you send an email to "support@" the name of the company listed in the lamp link, it will get to me. I'm not advertising at the moment due to life being busy, but I am doing work. I hate to be cryptic but when I had a public email, I could barely keep up with it. Thanks so much for signing up for the membership, that is really awesome. I appreciate it.
my colour wheel was broken. I replaced it with the help of this video. Thanks Frank!
Hey Frank,
thank you very much for your video. Ive got the W1070 since 2013 and ive had blurring and flickering so badly. So I decided to give it a try and clean the whole projector.
It was definetly a mess but after all steps especially the sensor and colorwheel cleaning, it works like day one. Iam so happy and thank you so much for this helpful video.
Best regards
W1070 still intermittently shut down with red Lamp and Temp led after hours, that is after I replaced the stock 3800 hr lamp (original owner) and color wheel with new ones from purelandsupply. The new color wheel can turn additional 1/8 turn freely when I manually turn it, while the old one stops turning immediately. The color wheel sensor looks as clean as new, no brown smudged like in your video, but I cleaned it anyway, along with all 4 fans. The only improvement after new parts seem it shuts down less frequently, like sometimes it can last 4 hrs without problem, but still shuts down every other day after 2 hrs, while the old lamp and color wheel shutdown after an hour everyday. Both case can turn back on for at least an additional hour after shutdown. I did zero the lamp hour.
I suspect the new color wheel is still not good enough, especially there is a tiny scratch on the color pattern, and it does not turn more freely maybe an additional full 180 degree when I manually turn, Or maybe the new color wheel has been unused for so long so it needs time to break in, so the friction from its bearing overheated the projector from time to time? However the new parts does improves a lot on the image depth and has more vibrant color.
Lamp and temp LED mean a fan is a problem or dust is built up. The color wheel is okay. I can't say which fan, but if you check the service menu, it will say which fan is erroring. also make sure you didnt turn the exhaust fan the wrong way. It should blow out. It is easy to reverse it without knowing. Your issue is thermal related. Lamp led means, lamp had to turn off or cant turn on. When you see it with the temp LED , that almost always means a fan.
Great work.
I got a Benq w1070. When i turn It on, in one minute, the lamp turn off.
Today i try to clean the color wheel.
Thanks.
Did it work?
How did it work for you?
Perfect timing for this video. I'm just in the process of changing my colour wheel over. It seems to have shattered on me!
I hope it was helpful and you are now watching your projector!
@@FixitFrank Still waiting for the part to arrive, but thanks to you I'll have a great chance of getting her working again.
If you get stuck, get in touch!
Detailed and explained as always. Thank you Sir Frank!
thanks man, I appreciate that.
Hey Frank, I'm looking for some input. I've got a BenQ W710ST that the lamp wont ignite. It turns on and after about 10 seconds a fan kicks on, the lamp light goes solid red, and the power button flashes orange. No light comes from the lense. So far I've thrown a couple parts at it, I replaced the power supply & the ballast. I've also tried cleaning the sensor on the color wheel. Still not fixed. Any ideas what I should try checking? Thanks.
What led you to the power supply and ballast? Was the PFC voltage low/non existent? What about the ballast control lines? What did you measure there that led you to the ballast? I'm also guessing you confirmed the color wheel index pulse is correct?
My usual process is confirm/verify the voltages and then track down which component is causing the wrong voltages.
What about a new lamp? Did you try a known good lamp? In my experience lamps are 90% of the issues then color wheels(for dlp).
I'd make sure you have a good lamp and start over and make sure that thenl color wheel is spinning properly. Then work your way out. Good lamp and checking voltages is your best bet.
@@FixitFrank The power supply had a brown area on the bottom that looked burned so I replaced it. I knew the entire lamp assembly was new, so I just thought logically that it must be the ballast that was bad. I didn't measure anything, mostly cause I'm not sure what to measure. I have a good multimeter though if I need to check any voltages. Can I check a pulse with multimeter at all or do I need to get a scope?
If your meter has HZ/frequency you could. I also have a few videos on troubleshooting color wheels without a scope. you might want to watch this first. th-cam.com/video/HC0u08IjAY0/w-d-xo.html
2 Legends in 1: The 1070 and Frank himself
Thanks buddy
Just a suggestion, to remove nicotine I use a degraser to clean kitchen in Italy it is sold like "chanteclear" I don't know the brand in US but it Is very helpfull for those jobs, just need to spray it on dirty surfaces and it melt nicotine, then wash with normal water and the item is like brand a new!
Thank you so much! Is it this stuff? www.amazon.com/Chanteclair-Sgrassatore-Ecodetergente-Friendly-Degreaser/dp/B00VKODPHK I will be glad to try it. It's honestly been a while since I dealt with nicotine. Back in the day, it was just part of everything. I can think of a few other uses if this is as powerful yet safe for certain surfaces as it seems.
@@FixitFrank Yes Is just this! It Is very powerfull to clean nicotine and other grease dirty. Just One bad side, It has very strong smell not bad, like old soap, but It melts any kind of dirty.
Thank you!! I will order and try it out. Grazie per l'aiuto! La mia famiglia è abruzzese, ma il mio italiano è povero .. :(
@@FixitFrank I'm from Napoli but my girlfriend is from Denver and now She lives in Salem (OR). Before the covid time I was in US every year, I Hope to return this year :) Where you live in US? I learn my poor english from my girl.
I am in Pennsylvania, about an hour south of Philadelphia. I promise your english is far better than my Italian. but I am working on it. :)
Nice work as always Frank!
Hey Frank,
thank you very much for your Video. I have a BenQ W1400 that shuts down after a short time (~60sec). The Picture is fine though, so its probely not the colour wheel. Anyways, I fully cleaned everything following you example (ALL Fans, Color Wheel and Sensor, everything else) but the problem remains. I noticed that each time I turn it on, the Projector shuts itself of a little faster. So first it says on like 60seconds, then 40, the 20 seconds. There is no error code, the thing just suddenly switches off. The Lamp is old (still the first one I think) but only has maybe ~2500h.
I thought it could be a problem with the power supply. The Caps seem fine on the outside but I have no tool to test them.
Thank you very much! That sounds like a lamp issue to me. 2500 hours is more than enough. I would try a new lamp first because without knowing 100% your lamp is good, that may be the root cause. It is also the easiest part to get. If the lamp LED flashes when the projector shuts down, that would be my initial suspicion. Especially if you are running in eco mode. Eco mode runs the lamp at lower power and can cause deposits to build up on the arc points. Unless the lamp is put back into standard mode occasionally for a few hours, those deposits can cause the entire module to fail early. That is what it sort of sounds like. If a new lamp does not solve the issue, then more troubleshooting would be needed, but I really suspect your lamp at this point.
@@FixitFrank Thanks so much for the Tipp, I will try that. Keep up the awesome work :)👍
@@FixitFrank I installed a new Lamp but the Problem remains. Also I noticed that I can't turn the projector immediatly on again after it shuts down. I have to wait a Minute or so.
Ho Frank good video..i have a issue image with my benq w1070 they look posterized..do you think it is necessary to clean the color wheel sensor or is it enough to resync the color wheel from the secret menu??tanks for your video
You could try adjusting the settings but I would suspect the wheel is on the way out or if the lamp assembly was replaced recently, I would make sure it has the right IR filter on the front. Make sure that glass has a red tint to it. If not, send it back and get one elsewhere. If the lamp is still the old one, then I would replace the wheel. They are cheap and you will be glad you did.
@@FixitFrank thank you very much.. the lamp Is the original..i will try to open the projector and check the wheel.. i will update you on the results.. hoping i dont need your advice again..and sorry for my bad english
I am happy to help if you need it! Your English is perfect. My relatives in Abruzzo could learn English from you! Il mio italiano non è buono
hello my friend, congratulations on your work!! can you help me ?
I have a Benq W1070+ which is giving me problems... I bought it used with an Osram lamp with 230 hours of use. It worked for 70 hours and started to make a high-pitched noise, like a hiss or a resonance then a moire on the brightest areas. After disassembly, I identified the noise coming from the color wheel. I then went back up, then did some tests by changing the display frequency, which influenced the noise of the color wheel. I then adjusted the color wheel sync in the hidden menu, which fixed the moire issue but not the noise. Then I wanted to adjust the gamma and everything went out suddenly with a steady green power light and a steady red lamp light. Impossible to restart since, it turns off after a few seconds without the lamp coming on. the wheel a little then stops but no noise. would you have an opinion? thanks in advance. Sorry for Google trad...
Hello! No problem! It sounds like the wheel itself is bad. If the wheel cannot run properly the projector will shut down and flash the lamp LED. They use a small oil-bronze bushing which wears out. I would purchase a replacement wheel. Any ebay/aliexpress wheel is fine. If you like, you can contact the people I use. They are in China. They ship worldwide and take paypal. Gydz@timeprojectorlamp.com is their email. I hope this helps!
@@FixitFrank thank you for your help, I think there is no longer any doubt about the color wheel breakdown. But there is something strange, the projector turns on directly when I plug it in instead of being in standby with orange power indicator. When off, the power indicator remains green with the lamp indicator red. both do not flash and remain fixed... I hope there is not another problem besides the wheel... and I also hope that the timing adjustments I had made before it dies will not prevent the new one from working properly. Your work is impressive and your videos helped me a lot to understand where the problem was coming from so thank you very much!!
Thank you! Make sure the mainboard is lined up with the low voltage pins. That symptom of the two LEDs usually indicates the power pins from the mains supply are not plugged in the way they need to be.
@@FixitFrank Are you talking about the long pins visible when I remove the motherboard? I checked and everything is connected correctly. do you think there is another problem?
The bulb blew on my w1070, i replaced it but now it shuts down a few seconds after the blue benq screen . No time to get to the menu to reset the lamp timer. I see the color wheel spinning but there is some flickering when the lamp timer warning is displayed immediately after the blue benq screen. I would certainly appreciate any thoughts. I think I hear some process try to start up then the lamp shuts off and it goes into shutdown.
@@bjbarns where did you buy the lamp? Sounds like it has the cheap IR filter glass. See if tbe face of the lamp has a red/blue/purplish color tint to it. If not thats probably the issue. If it's kind of greenish or clear it's letting too much infrared light through and it confuses the color wheel sensor.
If you still have the old lamp, try swapping the glass square on the front of the housing from the old bulb housing into the new housing.
Hello, awesome video thank you !!
I had the same issue, tried to clean everything including the color wheel sensors (which seemed quite good and was spinning well), but still didn’t work with the flashing colors at the end before shutting down, with the red lamp led up.
I think I will have to replace de color wheel. Do you know if there is a specific serial number for it ? And should I replace de small chip that goes with the color wheel ?
Thank you again !!
Hi Shino, If you replaced the lamp assembly recently, that might be a cause. The lens on the front can have the wrong coating and let too much IR light through and it will cause the wheel to go nuts. If that is case, you want to return the lamp and buy it elsewhere. Amazon sellers are notorious for this.
Otherwise, if the lamp assembly is OEM or good quality, and the wheel is still the original, then replacing the wheel is your best option. There is no special number for it and the sensor can be left alone. Just order a W1070 color wheel from Ebay or contact Time Electronics (who I use). Gydz@timeprojectorlamp.com
I just bought a new OEM lamp from Amazon so I guess the issue is the color wheel, I’ll try to get it replaced
Thank you a lot ! You are really saving me with your videos and quick answers
OEM from Amazon? I never saw one for sale there. I'm very suspicious of the lamp assembly. Who was the seller?
@@FixitFrank Ah sorry, it might not be an OEM then, I wrongly used that word, but it has the same serial number (OSRAM P-VIP 240/0.8 E20.9N)
I bought it from France though, the seller’s name is dse.one, but it seems legitimate to me
Before buying another color wheel I’ll try giving another cleaning, and try to blow some potential dust in the black box that supports the color wheel, maybe I didn’t do it well the first time…
ahh, Understood! That lamp will be fine. I was worried you replaced the entire housing with an amazon product. Just the lamp (since it is Osram) is perfect. You can try adjusting the color wheel index setting in the menu as well. Press menu, then press source and enter at the same time. USe the arrows to navigate to find the index setting and adjust that to see if it helps. write down the original number so you can go back to it if the adjustment does not help.
Hi, I have a benQ w1400 that had colour wheel issues - flickering etc. i replaced the colour wheel and now the projector is acting like it cant detect a lamp. i turn it on, it makes the noise of the wheel (freely) spinning up multiple times then stops, then the lamp ref flashing light turns on. if you take the lamp out and run the projector with no lamp this is the behaviour you would expect, but it does it lamp in or out. i have made sure the button that closes the case is pressed down, i cant see any other sensor areas, i replaced the lamp completely, i put the original colour wheel back in (that was spinning up but glitchy picture) and its doing the same. i replaced the ballast!! still the same! i also replaced the optical detector on the wheel. prior to me installing the new wheel it was booting up and lighting, now it seems to think there is no lamp in the chamber! the lamp install seems overly simple. one screw holds it in, and a 2 pin plug. anyone have any ideas? this is driving me nuts!!
Just came across your channel! Have you ever come across an odd problem with the W1070, where it'll shut off after an hour of use? A relative is having this issue with there's where after an hour, it'll shut off, and it can be restarted within 2-3 minutes of letting it sit.
find out which of the LEDs is on or flashing when that happens. It could be a few pretty simple things.
@@FixitFrank Thanks for responding Frank! From what I was told, the power LED lights up red nothing else.
Do me a favor and ask them to give you the led flashes when it shuts down. If there is a failure, it will flash the lamp LED or Temp LED. If its just a red power led, that is not indicating an error. That is normal operation. They may want to see if someone set a shutdown timer in the menu. You can set these to turn off after a period of time. A factory reset may clear that setting if they are not sure where it is. But only if none of the other LEDs are indicating an error. I would expect to see a temp or lamp error if there is an actual problem.
@@FixitFrank I just checked, they're telling me the power LED flashes red before it shuts down. They said it's been awhile since they used it, but that's what they recall.
@@FixitFrank Hey Frank! After looking at it in person, it seems like the lamp is bad? The projector powers on, and the lamp light is just a solid red. The fans do come on and spin, like its running but there just isn't any picture. But it did stay running for an hour-ish without shutting down.
Hi Frank. Thanks a lot for your videos, they are absolutely great! I have a Benq W1070 that developed a bad case of dust after I changed the lamp and cleaned the projector it with a vacuum cleaner (bad idea it turns out). You can see it here:
My question: can I just blow some air inside the “inspection cover” of the optical assembly, as you did in your video “BenQ W1080ST DLP Projector Cleaning / Service P2” (min 10:55) or do I have to take the whole optical block apart (or send it to the repair shop)???
Thanks a bunch!
@@alexolazabal4184 Id try it through the inspection port. Worse case, look up one of my DMD replacement videos. Its really not that bad to take out the DMD, but you may be able to get it clean through that hole.
@@FixitFrank Thanks a lot, Frank! As usual, great advice and encouragement 😀
Hi again Frank! I went ahead and cleaned the projector following your video very carefully 👍
I got rid of the dust, but when I started it again it became very noisy 😨. Within 5 minutes of being on, the temperature jumps from 265 to 380, and the fans go from 2400 to 3700 rpm. It sounds like the Benq is about to take off or explode, so I turn it off!!!
Thanks guruji
I face a faulty one of these at least once a week. I prefer the 1070+ model. It has 200 extra lumen and has both horizontal and vertical keystone as opposed to 1070's only vertical. To get rid of nicotine this is the best: Amberclens Ambersil Anti Static Foaming Cleaner 400ml
Hello Frank, hello friends. after viewing this video i bought a used 1070 too, bc looks like it is easy to maintain the projetor.
Unfortunately it has a problem, because after a few minutes use with perfect picture the image starts blurring, flickering, discoloration, ... so i believe its a heat issue.
I have searched the whole internet, but i could not find a hint what could cause it it.
Please help me.
Thx R.
I checked the service menu, but there are no errors / problems shown.
Hello, that sounds like a color wheel problem. The symptoms you describe seem to indicate that to me. I'd try cleaning the color wheel sensor and also make sure the bulb has a proper IR block coating. The front glass should be reddish not clear or green. If it's not reddish or purple tinted that would be a definite issue.
@@FixitFrank Thank you very much for your fast reply. The front glass has a reddish coat. I will check the color wheel/sensor asap.
Cleaned the color wheel sensor today and now everything is fine :) . Thank you very much for your help. +SUB ^^.
hello i ha ve done everything like shown but now projector is not starting, onlly green power blinking. any suggestion
Hello! Yes, check the power connection between the mainboard and power supply. If the pins are offset to one side, that can happen. It is easy to offset the pins but thankfully it will not damage anything.
@@FixitFrank thks very much but which one is the power connection. everything seems good...
but still no light; only green power blinking
i dismantle everything now it works!!!
thx for your videos
I go over it in the video. The power pins. I say not to misalign them during reinstall. It may 'look fine' but clearly something isn't. You didn't do something because it's not working. Go back over your work and reassemble it. Paying extra careful attention to the connector that plugs into the power supply. That's the only thing that could be the cause unless you accidentally damaged the main board somehow.
Hi Frank. What is the fix if the color wheel is slightly misaligned? There is a dark discoloration on the right side of my screen. Also, my housing is falling apart. Is there a way to permanently bypass the button for the bulb cover? My housing won't seal tight enough to hold it down any longer. Thanks.
Probably the light tunnel not the color wheel. They cant be aligned or adjusted but the light tunnel can. I'd search some of my light tunnel vids to get a better idea.
@@FixitFrankI'm struggling to find any light channel videos. Can you point me in the direction of one? Thanks.
@@FixitFranki found a couple of your light tunnel videos but for the life of me, I cannot find the side to side light tunnel adjustment screw on a W1070. Thoughts?
Hi,
How to save the changes in service menu ?
Nice
Sir, I have a w1090 benq. When I press the power button , green blinks a couple of times but bulb does not glow. No temp/lamp error and 2 fans on chasis is working, but the blower attached to lamp case is not working. I opened the projector up, when I manually press the cover sensor, lamp glows for 3-4 seconds and shuts off..when I tried running without lamp, the color wheel is not spinning at all..can you help me pls. Is it a lamp issue ? Or some sensor
If the color wheel is not spinning, I would resolve that first. Be sure the wires are connected and that the glass wheel can spin on its own. They do fail and are sort of cheap to replace. If the color wheel will not spin on its own the lamp will never stay lit.
@@FixitFrank yes sir. Thanks to your videos I could disassemble the color wheel assembly. I guess the connectors (two dots near sensor) was slightly unseated. cleaned and fixed it again. The wheel started spinning. Attached the lamp and It lit up. Thanks indeed for your guidance. Meanwhile cleaned DMD chip too, resolved the occasional vertical lines too. Thank you.God bless!
Wonderful news!! Thank you for letting me know. This is exactly why I post these. I'm so glad it helped. Thank you so much for your kind words. :)
Smoker ick .. Im not watching this video of a piece of equipment used by a smoker.
not sure why you would penalize me for that. I just repaired it. Seems unfair and not very cool of you.
@fixitfrank how do I contact you for a cleaning?
If you send an email to "support@" the name of the company listed in the lamp link, it will get to me. I'm not advertising at the moment due to life being busy, but I am doing work. I hate to be cryptic but when I had a public email, I could barely keep up with it. Thanks so much for signing up for the membership, that is really awesome. I appreciate it.