Hello dost Really UT55 not available.Really in my plant UT35A, selec PID 330, Yudian, and of radix has been used. But don't, worry I am trying trying to make your video.Really I have indent the UT55 but availability of video depend will depend on availability of indented UT55A . But according user manual of UT55A it is not so far differences. Although I am trying to fulfill your requirement. Thanks
@@mdkhokonahamed1686 To control pressure in PID Mode Please setting are below For pressure transmitter Range: -1 to 16 4-20 ma Set CNT: PID Input section setting INPUT:4-20 ma RH: 20 RL : 4 SDP : 1 SH : -10 SL : 160 Output ot : 2 ( analog output put) Here pressure is controlled by using out like control valve or other like vfd etc. How we enter in programming there a video "Parameter setting for pressure, temperature level in PID mode. Please see that Note: Same parameter are for UT55A PID controller. If there be need of help, please comment.
Sir Yokogawa-UT55A Controller was like a little graphics, a little graphics was more than a setting, the graphics and SSR Output Up Speed Graphics and SSR Voltiz has no settings
Sir ut 32 a pid control input jp2 ( rtd) out put 4to 20 milliamps used to i/ p converter samson posinitor steam prv used my company pasturazer purpose. So pid set point 90.pv going 98,99,100, degrees going again down 85,84,83,up/down come how to adjusted proposanal, integrated. Derivatived value or how to calibraction samson posinitor pls video sir
For this you have decrease offset value.Take attempt by decreasing the Proportional value keeping I& D constant.During this change you can make derivative zero/off. What is the effect of this change please comment
Yes sir. My plant is the same pid available. U r video 's total i'am seeing good sir. ot 0.03 voltage select. Hys 0.2 na but witch common number & witch wire no pls tell me sir
Really in this video, operating mode(CNT) is ON/OFF mode and out put is selected Relay output (ot=0.03) Hys is used for ON below set point and off above set point.103 is common and 102 NO,and 101 is NC as you said. New video will be uploaded in 1-2 days which make you clear more.
U r video 's more help me sir. Tq
Hi sir pressure sensor relation vedeo &cilbetion vedeo tutorial upload- yokogawa-ut55a
Hello dost
Really UT55 not available.Really in my plant UT35A, selec PID 330, Yudian, and of radix has been used. But don't, worry I am trying trying to make your video.Really I have indent the UT55 but availability of video depend will depend on availability of indented UT55A .
But according user manual of UT55A it is not so far differences.
Although I am trying to fulfill your requirement.
Thanks
Yokogawa-ut35a
@@mdkhokonahamed1686
To control pressure in PID
Mode
Please setting are below
For pressure transmitter
Range: -1 to 16
4-20 ma
Set
CNT: PID
Input section setting
INPUT:4-20 ma
RH: 20
RL : 4
SDP : 1
SH : -10
SL : 160
Output
ot : 2 ( analog output put)
Here pressure is controlled by using out like control valve or other like vfd etc.
How we enter in programming there a video
"Parameter setting for pressure, temperature level in PID mode. Please see that
Note: Same parameter are for UT55A PID controller.
If there be need of help, please comment.
@@ultimatesolution9935 thanks sir i m very happy
Sir Yokogawa-UT55A Controller was like a little graphics, a little graphics was more than a setting, the graphics and SSR Output Up Speed Graphics and SSR Voltiz has no settings
Sir ut 32 a pid control input jp2 ( rtd) out put 4to 20 milliamps used to i/ p converter samson posinitor steam prv used my company pasturazer purpose. So pid set point 90.pv going 98,99,100, degrees going again down 85,84,83,up/down come how to adjusted proposanal, integrated. Derivatived value or how to calibraction samson posinitor pls video sir
For this you have decrease offset value.Take attempt by decreasing the Proportional value keeping I& D constant.During this change you can make derivative zero/off.
What is the effect of this change please comment
Pid back side connection relay connection witch one terminal given sir
Have you need of connections details???
Yes sir. My plant is the same pid available. U r video 's total i'am seeing good sir. ot 0.03 voltage select. Hys 0.2 na but witch common number & witch wire no pls tell me sir
207.208 4 to 20 milli amps out put. I think u r connect relay connected 103 common 102 NO correct na
Really in this video, operating mode(CNT) is ON/OFF mode and out put is selected Relay output (ot=0.03)
Hys is used for ON below set point and off above set point.103 is common and 102 NO,and 101 is NC as you said. New video will be uploaded in 1-2 days which make you clear more.
Tq correct tq.for replay sir👍