Best solution will be with two relays in series. One using pulse and the other bistable mode. Pulse relay is activated on alarm and bistable on arm/disarm. One can deactivate a sounding external siren using bistable relay on/off switch.
Hello why you made a jumper on the siren between 1 and 4 ? Is it necessary ? So About Dip switch why you selected On in Polarity signal ? If selected Off anyway works ? Thanks
Can I use the MultiTransmitter Jeweller to connect an existing wired siren + wired sensors in an exsiting wired alarm to ajax? will the MultiTransmitter Jeweller also able to trigger the wired outdoor siren during alarm?
Hello thanks for this video. Is it also possible to have the siren beep or make noise on set delay on DoorProtect? Would love to see more Ajax related content. Regards
Good idea but we have a problem if power supply has gone (110v or 220v) The device won't work. So I advise you to put the device inside the bell and take the power directly from battery
You are right about that but i believe that it is not a good idea to put Ajax Relay inside the Siren because you will have problem with it's signal and maybe with humidity since Relay is for indoor use. Maybe it will be better to plug the DC power supply of Relay into a small UPS.
Καλησπέρα το μόνο θέμα ειναι ότι με αυτό το ρελε η σειρήνα χτυπάει απεριόριστα μέχρι να αφοπλιστει το σύστημα δεν έχει κάποια ρύθμιση για να σταματάει μετά από κάποιο χρονικό διάστημα. Σωστά?
Καλησπέρα πάρα πολύ ωραία τα βίντεο σας σας ευχαριστούμε πολύ μας είναι πάρα πολύ χρήσιμα. Μία ερώτηση παρακαλώ μου πρόσφατα σύνδεσα και εγώ την παλιά μου ενσύρματη σειρήνα με το relay ajax. Έχω όμως μία απορία όταν κάποια στιγμή μπορεί να γίνει κάποια διακοπή ρεύματος χτυπάει συνέχεια η σειρήνα.. Μήπως γνωρίζεις γιατί γίνεται αυτό και πως μπορώ να το σταματήσω να μη γίνεται;
Καλημέρα! Όταν η Σειρήνα ανιχνεύει απώλεια τάσης, τότε είναι λογικό να χτυπάει για λόγους ασφαλείας. Σε έναν συμβατικό συναγερμό στη διακοπή ρεύματος η σειρήνα δε χτυπάει γιατί είναι συνδεδεμένη στη κεντρική μονάδα του συναγερμού η οποία έχει εναλλακτική τροφοδοσία από μια μπαταρία. Οπότε στην περίπτωση του Ajax Relay θα πρέπει να συνδέσετε το τροφοδοτικό της Σειρήνας και του Relay σε ένα μικρό UPS, ή να προμηθευτείτε ένα τροφοδοτικό 12Volts με μπαταρία.
But if you open door protect when alarme is desarmed that will trigger the alarme too, no? Fox exemple if i put the ILS in the door and my alarme is off, by opening the door the siren goes on
Non ci posso credere... con questo collegamento la sirena suonerà al mancare della rete alla quale è collegato l'alimentatore. Inoltre, con 12V stabilizzati la batteria della sirena non riuscirà mai a caricarsi correttamente. Ma non è tutto, il tamper apertura e rimozione della sirena esterna non lo vogliamo collegare? Lasciate fare a chi ne capisce...
What Power Supply did you use? Relay requires 7 to 24 Volts DC. Normally an Alarm Siren requires 12 Volts DC but you have to check your Sirens specs about the maximum load current in order to select the correct Power Supply. I believe in most of the cases a 12Volts DC - 5 Amp should be enough.
Why conecting with relay another then ajax sirene🤪🙈. Ajax outdoor siren costs lower then to conect another with relay. Why do it easy if it goes complicated
You are right there is no need to do that in a new installation! But in an installation where you replace the old alarm system, maybe you could keep the wired siren.
![เปิดบ้าน โคตรสวย ป๋องกพล รู้จักตั้งนาน เพิ่งรู้ว่ารวย!!! l [Nickynachat]](http://i.ytimg.com/vi/tmgCF_2HfYI/mqdefault.jpg)
Best solution will be with two relays in series. One using pulse and the other bistable mode. Pulse relay is activated on alarm and bistable on arm/disarm. One can deactivate a sounding external siren using bistable relay on/off switch.
Hello why you made a jumper on the siren between 1 and 4 ? Is it necessary ? So About Dip switch why you selected On in Polarity signal ? If selected Off anyway works ? Thanks
Venitem ;) Nice work there you should use a mini 12v dc ups for the siren and relay for not going offline or triggering the siren.
You're right! Thank you for your comment!
Can I use the MultiTransmitter Jeweller to connect an existing wired siren + wired sensors in an exsiting wired alarm to ajax? will the MultiTransmitter Jeweller also able to trigger the wired outdoor siren during alarm?
Hello thanks for this video. Is it also possible to have the siren beep or make noise on set delay on DoorProtect? Would love to see more Ajax related content. Regards
Good idea but we have a problem
if power supply has gone (110v or 220v) The device won't work.
So I advise you to put the device inside the bell and take the power directly from battery
You are right about that but i believe that it is not a good idea to put Ajax Relay inside the Siren because you will have problem with it's signal and maybe with humidity since Relay is for indoor use. Maybe it will be better to plug the DC power supply of Relay into a small UPS.
Hi, with jamming/interference/low signal , the siren will sound??
Με το ρελαδακι μπορουμε να το ορισουμε βαζοντας στο pulse να χτυπαει για Χ χρονο. Τι γινεται ομως οταν θελουμε να σταματαει η σειρηνα και με αφοπλιση;
the triger should be normally close? so if any tamper it trigers the alarm?
No tamper protection with this setup
Καλησπέρα το μόνο θέμα ειναι ότι με αυτό το ρελε η σειρήνα χτυπάει απεριόριστα μέχρι να αφοπλιστει το σύστημα δεν έχει κάποια ρύθμιση για να σταματάει μετά από κάποιο χρονικό διάστημα. Σωστά?
How would the connection look like if you have two wires one 12v and one ground from the siren?
Καλησπέρα πάρα πολύ ωραία τα βίντεο σας σας ευχαριστούμε πολύ μας είναι πάρα πολύ χρήσιμα.
Μία ερώτηση παρακαλώ μου πρόσφατα σύνδεσα και εγώ την παλιά μου ενσύρματη σειρήνα με το relay ajax. Έχω όμως μία απορία όταν κάποια στιγμή μπορεί να γίνει κάποια διακοπή ρεύματος χτυπάει συνέχεια η σειρήνα..
Μήπως γνωρίζεις γιατί γίνεται αυτό και πως μπορώ να το σταματήσω να μη γίνεται;
Καλημέρα! Όταν η Σειρήνα ανιχνεύει απώλεια τάσης, τότε είναι λογικό να χτυπάει για λόγους ασφαλείας. Σε έναν συμβατικό συναγερμό στη διακοπή ρεύματος η σειρήνα δε χτυπάει γιατί είναι συνδεδεμένη στη κεντρική μονάδα του συναγερμού η οποία έχει εναλλακτική τροφοδοσία από μια μπαταρία. Οπότε στην περίπτωση του Ajax Relay θα πρέπει να συνδέσετε το τροφοδοτικό της Σειρήνας και του Relay σε ένα μικρό UPS, ή να προμηθευτείτε ένα τροφοδοτικό 12Volts με μπαταρία.
@@PoseidwnTech Σας ευχαριστώ πάρα πολύ να είστε καλά
Και εσείς το ίδιο!
Put the relay in the siren and powere it by the 12v battery. Less cables and "unlimited" backup power.
That's a nice idea! I will try it!
Με τη χρήση αυτού του ρελέ μπορούμε να συνδέσουμε και αισθητήρες άλλης εταιρίας ?
Για να συνδέσεις αισθητήρες θα χρειαστείς τον Ajax MultiTransmitter
Hi. The tamper with open siren and tear form the wall? Thanks...
You can connect siren tamper in a Door Protect sensor!
Very nice! But tell me something:when alarm starts when is nobody home,who"s gona stop the siren????? Try the scenario with pulse,not bistable
Ajax Alarm has cloud access through Ajax App, so you can disarm the alarm and mute the siren through the Ajax App!
But if you open door protect when alarme is desarmed that will trigger the alarme too, no?
Fox exemple if i put the ILS in the door and my alarme is off, by opening the door the siren goes on
For the alarm to be triggered you have first to arm. So if the system is armed and you open the door then the Siren will be activated.
@@PoseidwnTech If the system is off and you open the door, will that triger the siren?
No it will not! The scenario is only "By Alarm".
@@PoseidwnTech Thanks man, i will try it
Non ci posso credere... con questo collegamento la sirena suonerà al mancare della rete alla quale è collegato l'alimentatore. Inoltre, con 12V stabilizzati la batteria della sirena non riuscirà mai a caricarsi correttamente. Ma non è tutto, il tamper apertura e rimozione della sirena esterna non lo vogliamo collegare? Lasciate fare a chi ne capisce...
connected my siren to the relay there is a low voltage error in the app, can you help me?
What Power Supply did you use? Relay requires 7 to 24 Volts DC. Normally an Alarm Siren requires 12 Volts DC but you have to check your Sirens specs about the maximum load current in order to select the correct Power Supply. I believe in most of the cases a 12Volts DC - 5 Amp should be enough.
Strange I tried it with Pyronix bell did not work
I am not familiar with this Siren. Can you please send a link for the manual of the Siren to take a look?
@@PoseidwnTech i think i have done it i did same as you but used the enginner hold and disable the tamper
@@GUNITITSecurity hello, would you be able to share the wiring for the Pyronix Bell setup please? I’ve just got two and wondering best way to wire in.
I thought the outside siren is the circle one..
Why conecting with relay another then ajax sirene🤪🙈. Ajax outdoor siren costs lower then to conect another with relay. Why do it easy if it goes complicated
You are right there is no need to do that in a new installation! But in an installation where you replace the old alarm system, maybe you could keep the wired siren.