How to make Ebike from Old Hoverboard
ฝัง
- เผยแพร่เมื่อ 15 พ.ค. 2024
- Hello friends,in this video Iam making electric cycle with hoverboard motor
Parts used:-
old hoverboard
scrap laptop batteries
scrap smps
350w hub motor controller
36v(42v) battery charger
ignition key
electronic brakes
throttle
9T Ebike motor sprocket
metal pieces
speed obtain around 20kmph
DONT FORGET TO LIKE, SHARE , SUBSCRIBE
Subscribe to my channel:
/ jgprojectsyoutube
Thanks for watching....
#jgprojects#cheapebike - แนวปฏิบัติและการใช้ชีวิต
very good sir
,So beautiful
very nice car
It would be useable if it would have pedals. This tiny motor and small battery are good for assistance but not as the only power.
Very cool, congrats and keep up the good work.
Superb bro👍👍👍👍
well done keep up the good work
I like this types of inventions. Everything can be reused👍
what about used toilet paper
@@AlexParks121 Try and tell
@@dailygrow6961 no
Great project
Great diy idea, superb e-bike project 😍👍👍
Super bro
Super 👍👍
You haven't made an e-bicycle. You've made an e-scooter, since you don't pedal anymore. Either way, hella cool.
It would be an e bike because it's still a bike. It just doesn't have pedal assist so it's more of an electric motorbike
You should have more views
Найкраща саморобка на базі гіроскутера
What is that cylinder in the bottom bracket?
Put a dual chainring on the front and a 7 gear derailleur setup on the back Moosehead motor to the outside of bottom bracket put the cranks back in get a second chain then make a short chain to go from the motor to the smaller front sprocket and a longer one to go from the other front sprocket to the back derailleur like a normal setup so you can leverage the gears and get a lot of more out of that likely 10 or less newton-meter motor just like a typical mid-drive with gears like all the cool kids have instead of direct drive with no gears and your fuel put free wheel on your cranks it should feel quite natural when you're pedaling and when you're not I think but you know a lot more about bikes than I do so I'm pretty confident you'll figure that part out
shoulda got a bike with rear gears. could lower or raise the ratios :) more speed or more torque when needed
Делай натяжитель с успокоителем внизу перед большой звездой и будет долго работать а так молодец всё ок.
A donde venden ese motor? lo venden aqui en Mexico? Y si es a si , cual es la direccion ,y cual es el nombre del expendio.
You need to install one more hoverboard motor for make it run faster ⚡
10.41 into the video you did a test run of the motor.. It looked like it was off-balance and had a small wobble. This is not safe.. Also, your battery pack is a fire waiting to happen. Don't leave this thing unintended in your home even if it's not being charged. The whole thing of a death trap. But,,, at least you can say you tried. 🤓
Hey how did you figure out the electronics and control part of this, fabrication isn't a problem for me but I just can't understand the electric side. What controller is this and do I need to do anything other than just wiring it all up?
If you find the answer, please inform me, here need a hall Efected brushless controller 3 phase motor controller controller, please Help me
Boa noite muito legal
Weld the sprocket to the metal plate if you're able to. Definitely a safer option.
Best
Admiro tu iniciativa de tu proyecto, sin embargo, como crítica constructiva te digo lo siguiente puntos:
1- La especie de cajita que hiciste no tiene ventilación y se va a calentar tu controlador junto con la batería en periodos semilargos (imagina en periodos largos).
2-Al quitar los pedales no podrás pedalear y en cuesta arriba tendrás que bajarte a caminar junto con la bici ( debido a que el motor no tiene Torque y no podrá con el peso).
3- Al estar en constante uso el motor aunque este sea en terreno plano, se va a calentar debido a que solo él está jalando el peso de la bici y el tuyo (sabemos que esta es la finalidad) sin embargo, este motor no está diseñado para jalar el peso de bicicleta y el de la persona (ten en cuenta que en el hoverboard son 2 motores que se usan y que su carcasa es menos es 1/4 de peso de bicicleta aprox).
No tomes a mal mi crítica, te lo digo porque yo hice una, pero puse el motor en la llanta delantera y ahí puedo deducir en base a esa experiencia los puntos antes mencionados.
Saludos desde México...!
Cool
А сразу не догадался звёздочки наоборот.хотел 120км в час.😂
twin motor is faster and can last longer. single motor can easily overheat and burn.
i wonder if i can just simply put a hub motor and the stock hoverboard esc and bypass the on/off thing and manually put the sensor on the bike pedal so i just move my feet to move, im so stupid and smart i just might do it and i get a free battery pack installed that has a charging circuit
И что бы мы делали без гироскутеров ...
Todo esta muy bien hecho excelente pero por que no pusistes el chucho de encendido de la yave en el manubrio es mas facil por que si la llave se afloja se cae y pierdes la llave
my man didnt wanna clean or grease nothing
Dont do this without a spring tensioned chain. Direct like that its a toe chopping machine
What have you added to the motor shaft to fit in the cycle .where can I get it.nice build. At 1:53
I made it on lathe, with 32mm shaft
How can i get it or make it
@@ikechukwucollins8028 what's the diameter on your crank, I'll make you one and mail it to you, unleßs you have a 3d printer.
@@michaelmoreland5280 I will be so grateful
@@ikechukwucollins8028 take calipers to your crank after you pull it and tell me what they read
i see everyone changing sprockets, why notjust leave the larghe one from the peddle on and have geared back wheel sprocket? there is more than enough torque on the motor... what you did there is a waste of time. leave the small sprocket at the back.
speed ?
Hola, aqui en Mexico en que tienda venden el motor, y si es asi cual es su direccion, yel nombre del expendio.¡ me gusta la coneccion!!
Ruedas de hoverboard. En mercadolibre venden ruedas o el hoverboard a buen precio ,..de ahí partes , ahí mismo en mercadolibre venden el controlador y acelerador.
Notebok batery ?
Boa noite fiz o mesmo sistema igual ao seu mas o motor d hoverboard esta esqueitado o q pode ser se puder me ajudar agradeço
Y otra sugerencia a todos esos cables sueltos les hubieras puesto y uno grueso de color negro un fideo grueso donde estubieran todos los cables y te evitas meterlos todos juntos por el agujero
Invertí las relaciones pero atrás ponele una con velocidades de esta forma no le costará al motor lastima y agarra más velocidad.
Si tenes la otra llanta ponérsela en frente. E irá más rápido y no costará la salida.
What battery is suitable for a motor in terms of voltages and amperes
36v
@@jgprojects912 thank you
You need to Open this motor and change the three-phase coupling, from star to delta after the speed will be improved
And it will become 12v motor after transform
@@jgprojects912 no 36v
more speed and less torque
@@medshadow1 If you find the answer, please inform me, here need a hall Efected brushless controller 3 phase motor controller controller, please Help me
Can u tell me what the parts is? What do you call the sprocket at the back?
Ebike sprocket
А почему звëзды расположены именно так????
battery need be lot biggest. about 50AH have ok, and if buy motor better have 64-72Volt. dont buy 12-36V weak power no good.
its about 10kph?
About 20 kmph on full throttle
@@jgprojects912
It goes very slowly, with 20 km / h. I pedal and go at the same speed.
I saw this project and I want to build something similar.
th-cam.com/video/mzadJk8_w10/w-d-xo.html
But I go long distances (40-50 km). If I run out of power, I'll pedaling !
Why did You changed the large chainring to the back?
Because motor has high rpm and low torque
And to increase torque I put large chainring at back
What's your approximate maximum range and top speed?
your mother
BOAS NOVAS ON LINE
(Brasil)
Friend help me with a brushed controller d 30 vts 500w 28 A. XUN brand.
I don't know how to connect this device, on the accelerator with a contact key, this accelerator has 5 wires
(On Throttle Socket: Green, Black and Red)
(separator: 2 wires; Yellow and blue.) This throttle has a motorcycle key and battery indicator.
on the brush controller there is a white socket written: (Derailleur) in the colors green red and preto. I already know it's the accelerator but what about the two yellow and blue wires????
where can i plug it in?? we have two blue wires in a white socket written lock two blue wires written lock; what are these two wires for?
It will be better to ask to seller for connections
Mine controller is different
U should switch the sprockets round and it’ll go faster
Can you please provide buying link of Hoverboard motor.
buy a broken hover board on the used market. in the UK you can buy them for £10 or so. Strip it, boom you have your motor
it also may have a decent speed controller with it
Contact me for new motor
@@ajaymixup4396 number
range?
With those batteries (4.5 Ah), about 5 km.
That big sprocket at the rear is like having it in first gear.
Just like riding a bike in first gear you'll be going nowhere fast.
First Gear is good for going up hills and for the first 3 seconds riding on a Straight road.
exactly
This motor has Hall sensor, so how do you manage that? & please share controller link.
It is 350w bldc hub motor controller
Puikus hobis.verta pabandyti
I just dont get why his using masking tape to cover the battery's up surely that's a fire hazard it's not made for that masking tape is made for painting lool 😂😂😂
very slow speed
Why can't I read the comments?
little ugly box haha, i add my bike nice elektric box, you have wery little battery need lot more if want drive good. and 350W motor have too little bicykle, no power lot no go up hill newer ,need pedals help lot, minimum bicykle motor need be 500W good have 1000-2000 W if want comfortable drive. i has build 4 E-bicykle now cheap controllers and motors, but true have better buy 1000W motor only not less.
U
wrong gear ratio man....u only got 10 km/h top speed,because the rpm motor hoverboard about 400rpm