Amazing to have this knowledge. I wish I knew all that you know to be able to fix these appliances. So much waste in our economy because it cost so much to fix something that is so cheap new. But fixing these things and knowing electronics is such a great hobby and skill set to have.
Sir ur demonstration is excellent . As per my experience,almost boards consisting of active & passive components suffering from dust, humadity , dry solderings Cleaning is too essential before surgery keeping safe from hair crack . Durgapur wb.
thank you Sir for sharing and teaching. but I'm afraid I cannot do it because I'm not a technician. I don't have tools like that. and I don't know how to use it. maybe I will borrow from my friends and follow your video step by step.
Hi Sir, greetings from Brazil! Thanks for your video. I’ve bought an Induction Heater Rice cooker from Japan, which is 100 volts. I want to use here in Brazil using 127volts. As the induction has a transformer to power the coils, Do you think it will be possible to use it as is? Or there are a risk of blowing all the circuit? Thanks again!
Los IGBTs se pueden dañar por que la señal de activación viene espuria desde la etapa de control PWM, igual los componentes de su circuito driver se pudieron dañar. Si se tiene osciloscopio antes de montar el IGBTs se visualiza la señal de activación. Otra situación es que los puentes rectificadores se dañen por baja tensión de red.
@@alexandrebensi1127 en las soldadoras inverters generalmente se debe a que al haber una baja tensión los condensadores exigen una mayor corriente que termina dañando un diodo. Igual condensadores defectuosos de fabrica o que se están secando generan esos daños. Generalmente cuando se daña un puente yo cambio los condensadores
@@proteomicrotronicsempresa2030 entendi, Porque es uno inductor. Gracias. Yo queria reducer la potencia en 220V, imaginei reducer la tension.. no puder hacerlo
In your underneath coils, I notice that there is a coil from one side that goes to the top and then fastened down to the opposite side. Such is lacking in mine. Could it be the reason why my induction stove is not heating up? It powers up so that electricity could not be the issue.
Good day sir, I have a Snappy Chef I had the same problem. No power from the start. I replaced the IGBT and Bridge Rectifier. I have power now but E0 error as its not picking up the pot/plate. I have check the 400V/4.7uF Cap (Broken) Also 5 resistors are very far from the resistance tolerance value. I am going to replace the capacitor and resistors. I hope that it will work. Any comments from your side would be highly appreciated. With Kind Regards
I have a buffalo induction hob. 3kw countertop I use in my cafe. It’s great but sometimes won’t turn on.. having to switch it off and on to get it too work. I feel it’s something we aren’t doing right. Any ideas???
First you have to remove the protection but it is risky because the coil works with high voltage. I made one around 600W but I don't know if it will work for you. th-cam.com/video/ZvR92HLy6qM/w-d-xo.html
I have a blown mains fuse that I reset. Forgot to use the lamp while repairing. The induction heater fuse is not blown. there is IC blown md12h. An there is T FUSE like resistor blown. What to replace the T Fuse with? I ordered IC from aliexpress
please help, if I turn mine on the breaker pops instantly, I opened the induction cooker and looked but the fuses do beep so they aren't blow. Also I see no broken/burned components... What could it be.
My induction cooker doesn't produce enough heat. Previously it used to consume 1300 watts on meter now it's consuming only 600 watts. What could be the problem?
@@irbindey it's thermal paste, but I don't think that will fix your issue. That sensor is there as safety and for setting temp. "The cooktop can detect whether cookware is present by monitoring power delivered. As with other electric ceramic cooking surfaces, a maximum pan size may be specified by the manufacturer, and a minimum size is also stated. The control system shuts down the element if a pot is not present or not large enough. If a pan boils dry it can get extremely hot - a thermostat in the surface will turn off the power if it senses overheating to prevent cooker failures and potential fires."
![กี่หมื่นฟ้า | Your Sky Series EP.1 [1/4]](http://i.ytimg.com/vi/vLGjxFL6U_I/mqdefault.jpg)
Amazing to have this knowledge. I wish I knew all that you know to be able to fix these appliances. So much waste in our economy because it cost so much to fix something that is so cheap new. But fixing these things and knowing electronics is such a great hobby and skill set to have.
Sir ur demonstration is excellent . As per my experience,almost boards consisting of active & passive components suffering from dust, humadity , dry solderings
Cleaning is too essential before surgery keeping safe from hair crack .
Durgapur wb.
Thanks you sir for ur tios just few tols to use I have save my money to buy a new electric stove.🤝
I'm glad I was able to help you with this video.
You can install it upside down GBJ25K BRIDGE RECTIFIER face up directly and then weld the legs
Oczywiście
No
Because it heatsink side
estoy de acuerdo , va a disipar igual
Excelente video. Tuve el mismo problema y la misma solución 🤝
I'm glad if I was able to help with this video🙂🤝🤝🤝
Very good video quality and demonstration.
Thank you for sharing God bless always☝🏻🙏🏻
Fantastic works sir. Love it.
thank you Sir for sharing and teaching. but I'm afraid I cannot do it because I'm not a technician. I don't have tools like that. and I don't know how to use it. maybe I will borrow from my friends and follow your video step by step.
Perfectly done! Thanks for sharing ☺️☺️☺️
Thank you my Friend🙂🤝🤝🤝
Thank you my Friend🙂🤝
Awesome job & thank you so much :)
Great job as always Brother! ✌️
And it is better than original 😜
PS: 6:42 i know this struggle very well 😅😂🤣
And the soldering iron cable was unfolded all the way 🙉😆
Excellent post, congratulations, I wanted to ask you a question. If the + and - keys do not work, possible damage to the control board?
Thanks a lot!
Tkasih tutorialnya....sy menyimak .
Good thanks for sharing
Thank you a lot for video. Which paste do you use for rectifier and transistor? Where did you by transistor an rectifier? Thanks for answer.
Silicon paste
Verry nice
I think I like your soldering iron, can you give me the brand and specific of your soldering iron? Thanks. 😊😊😊
buen video buena reparacion y buen tip ... gracias
Thank you🙏🙂🤝
Would the cause of the transistors burning out be because the device we unplugged too soon, eg before the fan had cooled those transistors down?
I need to do this
Hi Sir, greetings from Brazil! Thanks for your video. I’ve bought an Induction Heater Rice cooker from Japan, which is 100 volts. I want to use here in Brazil using 127volts. As the induction has a transformer to power the coils,
Do you think it will be possible to use it as is? Or there are a risk of blowing all the circuit? Thanks again!
Thank you sir for your sharing. May I know what is the white paste use on the bridge rectifier.
This is the thermal conductive paste.
Los IGBTs se pueden dañar por que la señal de activación viene espuria desde la etapa de control PWM, igual los componentes de su circuito driver se pudieron dañar.
Si se tiene osciloscopio antes de montar el IGBTs se visualiza la señal de activación.
Otra situación es que los puentes rectificadores se dañen por baja tensión de red.
Porque baja tension en lá red danas los puentes? La potência se queda junto, no?
@@alexandrebensi1127 en las soldadoras inverters generalmente se debe a que al haber una baja tensión los condensadores exigen una mayor corriente que termina dañando un diodo.
Igual condensadores defectuosos de fabrica o que se están secando generan esos daños.
Generalmente cuando se daña un puente yo cambio los condensadores
@@proteomicrotronicsempresa2030 entendi, Porque es uno inductor. Gracias. Yo queria reducer la potencia en 220V, imaginei reducer la tension.. no puder hacerlo
In your underneath coils, I notice that there is a coil from one side that goes to the top and then fastened down to the opposite side. Such is lacking in mine. Could it be the reason why my induction stove is not heating up? It powers up so that electricity could not be the issue.
Bom dia parabens muito bom excelente
Thank you my Friend🙂🤝
Good day sir, I have a Snappy Chef
I had the same problem. No power from the start.
I replaced the IGBT and Bridge Rectifier. I have power now but E0 error as its not picking up the pot/plate.
I have check the 400V/4.7uF Cap (Broken)
Also 5 resistors are very far from the resistance tolerance value.
I am going to replace the capacitor and resistors. I hope that it will work.
Any comments from your side would be highly appreciated.
With Kind Regards
what is called the learning of these mother board and electrical things
Great !
I have a buffalo induction hob. 3kw countertop I use in my cafe. It’s great but sometimes won’t turn on.. having to switch it off and on to get it too work. I feel it’s something we aren’t doing right. Any ideas???
Kondensatory elektrolityczne w zasilaniu, utraciły pojemność, trzeba wymienić na nowe
Sir, what kind of paste do you put in igbt, thanks
só usa um transistor igbt?
Bro i have a question can i make a induction warmer for mechanical parts with this kind of kitchen ?
First you have to remove the protection but it is risky because the coil works with high voltage. I made one around 600W but I don't know if it will work for you.
th-cam.com/video/ZvR92HLy6qM/w-d-xo.html
Will it be possible to make this induction cooker to work with dc power 12/24 or 48volts, using less complex applications.
Greetings from Nigeria
It can work but with a smaller or the same size but rare coil.
I even made a similar prototype 3:00
👉th-cam.com/video/j89HrMeCvec/w-d-xo.html
Thank you for sharing this, if I understand, it will not be possible to convert/change the same stove. You have to create a new one.
Nice work..💪💪
Nice video bro ....
Hi, what's that white circle with liquid right on the center that I can see as soon as he opens it?
Heat sink compound on the temperature sensor that gives it good contact with the glass.
Buen trabajo amigo, lo que no entiendo para que el puente con los cables?
probablemente por que el integrado que ocupo no era el mismo y las terminales estaban alreves
Good old fashioned electric or gas solves that problem
Shorted diode and IGBT
I have a blown mains fuse that I reset. Forgot to use the lamp while repairing. The induction heater fuse is not blown. there is IC blown md12h. An there is T FUSE like resistor blown.
What to replace the T Fuse with? I ordered IC from aliexpress
please help, if I turn mine on the breaker pops instantly, I opened the induction cooker and looked but the fuses do beep so they aren't blow. Also I see no broken/burned components... What could it be.
wow emezing
Tengo uno pero solo calienta olla pequeña no grande.?????
excellent job !
My induction cooker doesn't produce enough heat. Previously it used to consume 1300 watts on meter now it's consuming only 600 watts. What could be the problem?
You better off just getting a new one because this looks like a lot of work and know how
Abi kolay gelsin bendeki ocak filip flop yapıyor göz kırpıyor özelden yardımcı olabilir misin sebebi nedir sana zahmet
Teşekkür ederim, soruyu tam olarak anlayamadım
@@ErCanEverything sosyal medya kullanıyor musunuz özelden video atıyım size daha anlaşılır olur
@muratakdemir1127 facebook.com/share/M8dGMG2YzSVthwJ6/
@@ErCanEverything yazdım Facebooktun abi
Hello what MOSFET and bridge rectifier can I use becouse I can't find exact match for the ones in my aobosi model I hope you can help
Do you need to put thermal paste on the metal sensor? Mine keeps having error that it doesnt detect any metal cookware on top
That is not metal sensor, that is thermal sensor. That is why paste is there, to better conduct heat and have more precisely measurements.
@@TheAlexXxA1991 thanks for your answer. Is that thermal paste? Or a different compound? I have one lying around for my pc
@@irbindey it's thermal paste, but I don't think that will fix your issue. That sensor is there as safety and for setting temp.
"The cooktop can detect whether cookware is present by monitoring power delivered. As with other electric ceramic cooking surfaces, a maximum pan size may be specified by the manufacturer, and a minimum size is also stated.
The control system shuts down the element if a pot is not present or not large enough. If a pan boils dry it can get extremely hot - a thermostat in the surface will turn off the power if it senses overheating to prevent cooker failures and potential fires."
@@TheAlexXxA1991 ik but it disassembled it was not sure what to putnthere
Before replacing igbt ,points voltage not checked wrong impression.
I change the igbt and it works for 10 minutes and then it goes short again, what could be the problem?
Fan is running But no light in display and pannel board is not working what is problem?
👍👍👍
I have no idea what he just did.
Location ng shop bossing
yeah,TheFuseShouldBlowToProtectTheIgbt.
Slayer please..,..
Fault code? 03 ?
My iduction plate shows er 42
Köprü diyodu tersini çevirip direkt takabilirdin...
Pasaron más de 10 minutos.
Let it be 11 minutes, if not 10 minutes.😅
In the first 30 seconds I showed you it doesn't work and I was ready at 11:30😉
Music just killed me. Could not watch it with sound. LOL
🤠😄
🤣😂😅 Bob Marley style...
Bob Marley Faruk😄😄😆
The mf is not replying to comments. So mean.
Mf
Waste of time
👍
Hahahahahahahaha... WHY???????????????????????????
You have a parts