BB30 is too complicated to become an international standard. I am going to continue using Shimano external bearing bottom brackets, they are much easier to service.
There are so many things wrong here it's outrageous 1:34 That is the incorrect way to remove the old bearing, freeze or push out from outer edges with the same installation tool. 2:15 both c clips were not checked against each other for gap tensions. 3:00 that is the incorrect install procedure, the bearings most be put in a freezer for a bit to contract slowly their size to then make them slide in easier without expanding the frame socket they sit on. Notice here the frame socket is actually being expanded!! At no time did they use a digital caliper to check the socket sizes of the bearing housings. This is a critical step to know of it will creak soon again. Overall this is not even close to how BB30 30 is supposed to be serviced. It's already a poor design by nature so these steps will make you ruin your frame only after a few rebearings.
見ながら出た言葉が、うわあめんどくせえなあだった笑
ウェーブワッシャとか色々なワッシャーがあって面倒くさいな。
面倒臭い割りに異音が高い確率で発生する。
シマノのプレスフィットのほうがシンプルで耐久性もある。専用工具も入手しやすい。
フェルトのバイクを買おうとしたらBB30だったので、辞めた経験がある。
BB30はキャノンデールが生んだ負の遺産だが、キャノンデール以外にも採用しているメーカーがあって困る。
圧入式は自分でメンテできないんで、田舎暮らしだと本当に困る。
@@asdfghjkl79134 方式にもよるだろうけど、シマノのは専用工具あれば取り付け取り外し簡単だよ?
専用工具もAmazonで数千円も出せば買えちゃうし、普通のネジ式BBと工具揃える難易度やコスト、作業難易度も大差ないよ。
フレームは軽量でとても素敵なのにどーしてこのBBをが出来てしまったんだ、、、、
ネジ山作るより手間が少ないから、コストカット、つまり金儲けのためだね。
アルミフレームはねじ切り式の方がコストがかからないと思うのですが、、
Thank you for this simple to the point video. My Japanese is limited, but it is easy to understand by anyone.
BB30の音鳴りで1年の間、ベアリングを4回交換、費用もすごくかかりました。結局、アダプタでシマノのクランクに変更して治りました。
BB30は最悪でしたね。楽しい週末のライディング途中音鳴り発生すると本当にテンション下がります。
ベアリングの費用とクランク代、アダプタ代すべて考えるとミドル級のカーボン買えたよな。クソ。
ちなみに作業も専門のショップで頼んでましたが、治りません。BB30は買わないのが正解。
ほんまそうだよね、bb30は最悪。こんなもんを発明したやつって頭おかしいんじゃないかな
メンテしてないから異音がなるのでは?
自分は全然なりませんけど?
あとそこまで異音がなるなら
アダプタ入れて普通のBB入れたらどうですか?
そしたらSHIMANOとか他のクランクも取り付けれますし
僕はCAAD12とシナプス持ってますけど
CAAD12にはSHIMANOのクランクを入れてます(アダプタ使って)
結局メンテしやすいし異音も多分無くなると思います
ちょっと工夫してみるのもどうですか?
工具なら通販で買えますしね
@@onozcup新車で購入して1年間4回ベアリング交換だと3ヶ月ことにベアリングを交換するペースです。
また、雨の日は乗ってないし、メンテナンスも200キロことに行ってました。
今はsuginoアダプターをいれてシマノクランクにしたので騒音は解決してます。
Bb30はフレームによって当たり外れがあるようです。
ちなみに僕のはcaad10で少し古いですが、最近のbb30Aは改善されたかも知れませんね。
caad13もBB30で、買おうか迷ってるんですがやめておいた方がいいんでしょうか?アダプタ入れてSHIMANOにすれば大丈夫ですかね?ウィッシュボーンってやつ入れてもダメですか?(初心者です。質問多くてごめんなさい🙏)
give me the reference for fsa hallograme Cannondale caad 10 housing bearing please ??
例のBB
bb30はまだ許せる
ただしシートポスト(25.4mm)
てめぇは許さん
めんどくさい(笑)
BB30ってどうなん( ̄ー ̄)
ゆーさん 異音がなるらしい
メンテしてたら異音は鳴らん
メンテしてないから鳴る
@@onozcup メンテし過ぎてもなるよ
クランクもrotorの方が簡単
rotorのクランクは取り付け取り外しでなるほど!
このクランクはナニコレ!(見かけはカッコいいのに)
give me the reference for fsa hallograme Cannondale caad 10 housing bearing please
初めてのロードバイクcannondaleだったけど、次はやめとこう、、メーカー選びはメンテのしやすさも考えないといけないって勉強にはなりました
Thank you for this simple to the point video. My Japanese is limited, but it is easy to understand by anyone.
Thank you. This is SUCH a clear and complete video.
Great video and very helpful….wish this was also dubbed in English….f@#$
Hay lắm bạn .
Domo Arregato
BB30 is too complicated to become an international standard. I am going to continue using Shimano external bearing bottom brackets, they are much easier to service.
this is the best how to video shame its only in japanese! thankyou anyway cannondale Japan!
Hay chuyên nghiệp .
BB30の異音っていつの話しとるんか
There are so many things wrong here it's outrageous
1:34 That is the incorrect way to remove the old bearing, freeze or push out from outer edges with the same installation tool.
2:15 both c clips were not checked against each other for gap tensions.
3:00 that is the incorrect install procedure, the bearings most be put in a freezer for a bit to contract slowly their size to then make them slide in easier without expanding the frame socket they sit on. Notice here the frame socket is actually being expanded!!
At no time did they use a digital caliper to check the socket sizes of the bearing housings. This is a critical step to know of it will creak soon again.
Overall this is not even close to how BB30 30 is supposed to be serviced. It's already a poor design by nature so these steps will make you ruin your frame only after a few rebearings.
maybe their goal to make everyone buy a new bike after few rebearings
BB30本当に嫌い。
フレームは結構高い買い物なのに、不具合の発生率高すぎる。
7☆▪◇
--
.c10
2回もベアリング入れられちゃったらガバガバになっちゃう〜
早くbsaに戻して〜!
でいるどみたいにねじ込んで〜!