How I Make Airfoil Wings| For Beginners
ฝัง
- เผยแพร่เมื่อ 26 ส.ค. 2024
- Are you a beginner at making planes and the you can’t find an easy way to make your wings well this is an easy method.. Making airfoils is crucial when it comes to aerodynamics for your plane all you need to make this one is:
-Foamboard
- Craft Knife
- Hot wire table cutter
- Sand paper
Link to how to build your own hot wire table cutter :
• How To Make DIY Hot Wi...
Wing Dimensions
- Wingspan 100cm
- Root Chord 16cm
- Tip Chord 7cm
Become my Patreon to support this channel and let’s grow together in return you will get exclusive content and files ♥️♥️
/ toms_hobby
Thank you for watching and going through the video description, make sure to like and subscribe.
TomsHobby
Become my Patreon to support this channel and let’s grow together in return you will get exclusive content and files ♥️♥️
www.patreon.com/TOMS_HOBBY
This is about the easiest foam wing cutting making setup I have seen! It should be really great for the KFM type airfoils as well....Thanks Laurie
Thanks.. it’s very easy to use if you have seen my other build videos like the Arrow wing or Mustang I used the same method
Mrna can change your dna and gmos can have a patent, they also can contain heavy metals & chemicals, do some research before. Mrna is a new vaccine method, old ones were actually safe. Also it's not FDA approved I read. Someone in my family died after taking it.
** RESPECT = YOU MADE IT SIMPLE
Congratulations from INDIA.. GOOD DIY
Thank you
Mrna can change your dna and gmos can have a patent, they also can contain heavy metals & chemicals, do some research before. Mrna is a new vaccine method, old ones were actually safe. Also it's not FDA approved I read. Someone in my family died after taking it.
I am new here on your channel i discoverd it now and you doing very good job i like it. good luck (:
Thank you
I like how your adjustable hot wire cutter is set up for long angles. It is a smart design, but I see one flaw. The spring should never be in the circuit. It is a coil which acts as a resistor, it is steel which is not a good conductor, and it looses tension when it heats up. The cutter would be much more efficient if you attach the power supply to the same end of the spring that holds the resistance wire. I have seen some people attach it straight to the wire with a clip that can slide up and down, and they use that to adjust the heat.
All I know for now is that without that spring at the end the cutting would have been really messy, when I first built for testing there was no spring and the cut was really bad
EXCELLENT
You can give it more finishing by smoothing it from sand paper and colour it to make it a shining wing.
good skill you have..
Nice one bro, thank you very much. What is the thickness of the Nichrome wire
You are doing well.pls where did you get your nichrome and, where do you buy your electronics.
Very nice bro I m subscribe your channel 💓💓💓💓 I m making mig-21 70mm edf jet🤗
Mrna can change your dna and gmos can have a patent, they also can contain heavy metals & chemicals, do some research before. Mrna is a new vaccine method, old ones were actually safe. Also it's not FDA approved I read. Someone in my family died after taking it.
Hello.. What foam density is it?
Can you point me in the right direction?! Thanks
Where do I find nichrome wire
You buy them here www.ebay.com/b/Nichrome-Resistance-Wires/181810/bn_78165557
You can find some in an old soldering iron
Respect = great job
Are you in USA?
I live in the Bronx
Let's get together
I need your Service. I will pay you
Unfortunately I don’t l live in Nigeria
@@TOMSHOBBY
Please provide me with an email
I will send you my design and you tell me how much
You will charge me and the shipping cos please
Tommi
I sent you an email
Is it possible we can have a Whatsapp conversation
I didn’t get an email
RIP sound
Sorry copyright issues
Show us how to fly it
Check out my other videos
😜
not easy