Tormek chisel sharpening - Mirror polished bevels on old scrap chisels
ฝัง
- เผยแพร่เมื่อ 12 ก.ย. 2024
- Tormek chisel sharpening - Mirror polished bevels on old scrap chisels
Hello friends and fans!
I just received 15 old and worn out chisels from a customer. She told me that the chisels belonged to her dad and grandpa, and now was the time someone took good care of them.
My job was to put a new beautiful bevel one them, and make them mirror polished.
And so I did. I didn't record all 15 because it took long enough just to make the big ones straight and even.
I use:
Tormek T8
MB-100 Multi Base
SE-77 Square Edge Jig
Diamond Wheels Coarse,
Fine & Extra Fine
www.woodcraftbyjonasals.dk
woodcraftbyjonasals
#tormeksharpening
Takes a while. Least your not ruining the hardness with a moder bench grinder
I learned something new today
Great video Jonas. I think I will have to get a machine like that in future 😄. Makes the job much easier
I totally agree! Sharpen all your tools in hand takes so long time.. Tormek helps a lot 😉
Great video brother
Thank you very much Mona 🙏🏻🌳
I was surprised you made no effort to flation the back. Other than patina was there a reason for that?
I totally forgot everything about that.. Really bad.. hehe
Can the back of the chisels be ground flat using the MB 100 jig and diamond wheel combination?
Never ever seen anyone sharpen a chisel on a Tormek using the side of the wheel
Hello Paul 👍🏻
That’s the diamond stones that makes it possible to sharpen on the sides, making a flat surface, instead of a hollow.
Really awesome!
You need to watch some more videos how to do it correctly. You start with the back side and then move forward in the process. Nice start but need some work on your steps.
Hello Haggard
Yeah, I realised that I was doing something wrong.. my bad. Next will be better, hehe.
You really should have used wet and dry to flatten the backs before re grinding an edge.
Nice video though
Agree
can you flatten the back of chisels using tormek ? using the side of the diamond wheel ?
Yes
How long do the diamond wheels last compared to stone?
When using that side jig how do you find the bevels
Very first step folks is to flatten the back. Then grind a new bevel. This is not what is being demonstrated.
Hey Gary.
Yeah, I noticed that right after I finished editing the video. Totally amateur, hah! Won’t happen again.
Flattened the backside afterwards and shipped to the customer.
Thanks for the comment 💪🏻💪🏻
How long did it take you to become proficient at using the Tormek grinder?
Hey dude!
All by yourself, it takes months or years to master it. But takes classes (easier online) and get all the tips and tricks you can get, it’s not bad at all. Months (2-6).
It’s worth it!
@@formgjortbyJonasAls Thanks for a quick reply!
Does it take much to maintain the grinder in good condition?
Sorry for showering you with questions, but I'm actually considering making an investment in this stuff :)
@@Owieczkin No worries man, that's cool. I can't be a big deision to invest in a Tormek (buy the T8!), because it's not cheap. But the quality is the best on the market, and trust me, you an earn it all back pretty fast, by sharpening knives.. in a week or two (if you now how to do it, otherwise, e few months).. I've eanred it back at least 20-30 times during the past 2-3 years. So go for it!
Oh and the tormek won't flatten the back on a chisel in that state. 80 grit wet and dry and work up to around 600 grit. The flat back edge is what guides the chisel as you know
Yeah, I realised after I made this video.. It's really bad. At least now I know!
Hi. Hope you don’t mind me giving you some advice..
for initial regrind (100 grit, start on one bevel until a full burr is reached, repeat same number of passes on other side of blade, and if there’s a new burr, move to the second stone… if no burr, continue until one is created.. then do one pass on each side… the blade now has a perfect geometry
Stone 2.. this will remove metal, all abrasive and polishing wheels do.. to keep the perfect geometry, do the sharpie test until happy.. then do one pass on each side until you are satisfied… if you do more passes on one side, the knife loses geometry, and you end up removing more steel than needed
Honing wheel… light passes, no more than light pressure. Mix your honing compound with a mineral oil. One pass at a time on each side, from heel to point.
I always use the following basics
Only remove the least amount of steel as possible
Clean wheels with a rare earth magnet, not sand paper
Perfect geometry means quicker sharpening
👍👍👍
Nice
Good job bro
Thank you Hussein!
You have to say you really have a great belt on your pants! 👍 He is in the 3rd hole and sits exactly on the zipper of your pants.
Jonas when regrinding old chisels, do you flatten the backs first.?
Hey Ernie
I actually did it all after this video.. totally forgot to film that too 🤯👎🏻
What kind of jigg do you use for the chisel ?
Hello Konstantin
The name of the jig is ‘SE-77 Square Edge Jig’. It comes as a standard with the T-8 Original ;)
Need to do the backs too... Otherwise no point. In 11:41 looks like you have a bit o a back bevel, perhaps just from you stropping.
Yeah, I realized.. after I finished this video. Doh.. I did the sharpening on the backside, so now I got a better understanding of chisels and how to sharpen them.
Thanks for the comment :)
You are rounding over the edge on the lether wheel. Can see this on the micro bevel and the edge not shaving very well.
Yeah, I didn't do a pretty good job there. Learned a lot, but makes me cringes a bit, hah. I'll do better in the next ;)
Thanks buddy!
my chisels doesn't turn out exactly 90 degrees with the 90 degree jig. they are off a bit on one side on all of them. Think maybe my stone is not even enough
Ok
Buy a new tormek
@@d.k.1394 nah. It was the stone that was uneven, bought the stone truing tool and it fixed the issues. Now im using a diamond wheel anyways and that works flawlessly
The diamond wheels are such a great product! So many benefits!
Would have taken forever by hand. Not really feasible.
IMHO a poor vid. No focus on flattening the back. Only half the job!
Yeah I admit. Realized after editing and shooting.. really stupid 👎🏻👎🏻
@@formgjortbyJonasAls that’s a bit harsh. Tough in yourself! Sorry didn’t mean to be rude - I was looking to see how it was done that’s all.
Hehe, it’s no problem Jeff. You’re not the first to mention 😉
I was totally green on chisels, and forgot all about the flat side. That’s was so noobish man, haha. Well, everything has its beginning 😄
Takes a while. Least your not ruining the hardness with a moder bench grinder