MÉTODO RESET FUSOR: Lo probé en una Samsung 5010 y funciona perfectamente para hacer el RESET del FUSOR. La secuencia completa es: MENÚ #1934 MENÚ Entras al modo TECH y vas a DATA SETUP. Luego eliges COUNTER RESET. Le das OK. Eliges FUSOR y le das OK. Y así todos los que quieras restear. (Tray 1, etc) Finalmente apagas y vuelves a encender la máquina. El contador del fusor estará en CERO.
Just tell me: what does it help that "el contador del fusor estará en CERO" if the fuser's mechanically damaged? Or the other way around: why would the fuser cause ANY problems (associated with a counter) unless it's worn or damaged?
RE CLP415-NW SAMSUNG LASER - I've endeavoured to release sticky label that broke off and perhaps impacted within the fuser area. A small piece was retrieved but there remains fragments that are preventing release. All other areas a clear. I've been tempted to unscrew top over to get better access. Would that help?
Hello Viandant ! Thanks to help me . I have a CLP310, when the paper goes out the toner does not stick on the paper. Is this a problem of the heated roller ? Thanks a lot
Please share how to upgrade firmware via usb in dead mode or in starting problem, samsung scx 6545,55n and also share shot codes like nvm initiliaze or hard reset in non working mode
Hello Viandant. Thanks for the video. I don't know why, but the toner seems not to properly attach to the paper. When i pass with finger it go away. Do you think it can be the fuser roller? Thank you
Hello, I have Samsung CLP300 colour laser printer and it gives me a paper jam just before the fuser it is happening when the paper is trying to enter the fuser and when I open the back cover I can see the paper all wrinkled and the toner on it is not developed. May I ask you how this can be fixed. The paper is not even entering the fuser and jams. Should I clean the fuser rollers or do something else? Thank you!
+undecided I think it's not a cleaning problem. verify if there is a foreign object near the fuser unit, may be the paper is dump, try change paper. check if the fusers are worn
I have a Samsung C1860FW and it gives me the message "Replace Fuser unit". I am not sure what to take out "Fuser" and whether its worn out or dirty and should be cleaned. Any suggestions? Thanks;.
should the pressure roller be completely smooth? mine is uneven, like small ripples in the rubber, is this normal or does it mean it's ruined? the roller looks clean but I still get horizontal (not vertical) lines when I print that seems to correspond to these uneven places on the roller. (ML-1660)
Thank you for the cleaning tips. My ML 1860 is clean, no marks on the fuse or elswere, but when printing, black spots are visible on the paper. My toner is 67 % full and really don't know what is the problem. The printouts of images are also kinda blurry and I noticed that my Samsung printer setting vanished with windows 10 updates lol
I have a CLP-415NW and Im getting blue spots on all pages that are the same size shape and position. I checked the toner cartridges and cleaned the rollers of excess toner. I don't see any defects in the green roller but the spots persist. What else do I need to check or clean? Thanks.
You suggested we ask questions. All of a sudden, I'm having having trouble with my Samsung laser printer. The light is green...and printer starts to work, but then stops...yet, I can find no stuck paper or other obvius problems. I need a new toner cartridge, btw, but with a little shake-up have been hanging in there with this puppy....until I can get to ordering the cartridge. Any idea what this might be? THANKS.
Which samsung? most of Samsung toner cartridges have chips, so it's useless to shake them if the chip is over. you can also try to clean the paper feed rollers with alcohol
hello can guide me.... I have a samsung printer ml 2955dw that when you turn on the orange light on the panel is highlighted and a paper jam message appears inside the printer but it does not have any jammed paper. the fuser rollers is clean.
yes, it may be a problem related to the fuser. Look at the fusers. If the fusers are damaged the problem is there. If not, look at the drum. if there is toner on it, change the toner cartridge. That type of toner cartridge give lot of problems
My samsung ML-1865 laser printer is printing a solid black print out. Changed toner still the same . cleaned pressure roller still same . Is their a solution please ?
I have a m2070Fw xpress, getting the fuser failure message #U1-2320, very frustrating as its just out of warranty. could cleaning them solve this problem?
the temperaturel of the fuser unit is abnormal, too high. try to turn the printer off then turn the machine on. If the problem persists, remove the fuser unit. Check if the fuser connector is connected properly. Check if the thermistor is twisted or contaminated.
if you can't remove the fuser unit, you can try to remove the paper one piece after another. make attention not to damage the rollers, use tools made of wood or plastic. not metal
hy sir, thank you for this video. I have an issue with one of my samsung -2161 printer, as of now i am getting random spots in page while printing page. What do now?
May be the toner cartridge is losing toner, on the recovery blade is damaged. clean the inside of the printer. check the fusers, if they are dirty try running a dozen of white pages
Thanks for Giving such usefull info about printers. I have samusng ML-1676P MonoChrome LASER printer. i found problem in Displaying RED light insted of Displaying GREEN light on starting of Printer with loaded Papers. There is no effect on printing with RED light, but i think printer may be heated without printing that's why the RED light displaying. Give me solution for RED light insted of GREEN light.
Thanks for the video! I have cleaned the fuser rollers, belt and cartridges but I still get bad printout. I have emailed you a photo of the print. I hope you can help me. Thanks!
@@viandant5 Thank for quick answer. I did it, but nothing changed. Paper si new, everthing is clear. I thing the roller surface is not more functioning. Any other idea?
@@velkytatko8879 It difficult to say without checking the printer. If nothing work may be there is something broken, the gear mechanism of the paper roller. I think that printer has to be repaired
Hello Viandant !! The problem is solved, I changed the fuser ! I noted the sheets of paper were cold, now they get out warm and the toner sticks. On the out of order fuser there are two thermal probes, is it possible to test them ?
+viandant5 Ciao! Possiedo una Samsung clp-550n, prima mi faceva una riga verticale per foglio dei 4 colori: ho sostituito il tamburo ed ora non lo fa più... Ma è arrivato un altro problema: con la vecchia fotounità dava il problema della riga ma i fogli uscivano bianco, invece con la nuova fotounità la stampa è senza righe ma i fogli vengono sporcati di grigio. Cosa può essere? In una clx-3170fn avevo una immagine ghost della stampa precedente, ho cambiato fotounità e questo problema scompare... Ma si evidenzai il problema delle macchie di grigio (in questo caso lievi) ai fogli. Ho sostituito anche la cinghia e ora stampa come nuova... La domanda è: il mio problema delle pagine sporche di grigio, può essere dovuto alla cinghia di trasferimento??? Eppure se metto la vecchia fotounità i fogli escono bianchi ma con la striscia dei 4 colori del toner. Nella clx-3170fn con problema ghost quindi ho cambiato tamburo (fotounità) e risolto, mentre macchiava le pagine di grigio e cambiando anche la cinghia si è risolto. Quel che mi interessa è per clp-550n: perchè il vecchio tamburo mi stampa le pagine regolarmente con sfondo bianco (ma essendo danneggiato fa anche la striscia verticale dei 4 toner) mentr eil nuovo tamburo giustamente ha risolto il problema dell'immagine ripetuta della stampa della pagina precedente ma ora però le pagine si sporcano di grigio uniformemente per tutto il foglio (o quasi)??? Grazie di cuore in anticipo per la risposta.
+Itanium IT sono macchine che cominciano ad avere un po di anni, è possibile che il nuovo tamburo fosse in magazzino da parecchio tempo e che sia scaduto o difettoso. se sostituendo il tamburo quel problema scompare è molto probabile che il tamburo sia il responsabile
mmmmm.. i have found this video by google after search some information about error #A3-3112 i obtain whiy a ML-1670.... i don't thinks what's the problems........ but i thinks i can trash this.....
I have a samsung Xpress Color printer. The print is coming out with a blue line like this ___________ ___________ down the center of the page. What can I do to fix??
the fuser unit contains a heat roller, & pressure rollers only. you are indicating there is more then ONE heat roller or pressure roller. There is not.
Hi. I have a Samsung SL-C1810W printer. When I print a photo there are lot of visible vertical line entire width of the paper. I use original cartridges and current set is more than 1 years old after replacement since I do not print much. Is it a problem with the cartridges? What should I do. Below is a demo page printed which shows the vertical lines. www.mediafire.com/view/q8wxgt757hr1h86/IMG_7225.JPG
The second most probably culprit is the OPC drum. If you keep the toner cartridge in a dry place with a normal temperature, the expiration date is not important
The OPC drum is in the cartridge which is not replaceable isn't it? Is there any type color test page which I can print individual colors and find which cartridge is faulty?
the drum is into the toner cartridge. Print a page with a square cyan magenta black and yellow and look where is the problem. it may be the transfer unit too
it's an error of the fuser unit. Turn the machine off and on. Check if the fuser connector is connected properly. Check if the thermistor is twisted or contaminated.
Thank you for taking the time and trouble to make this video. It helped fix my problem. Somewhere, sometime on the interwebs I will buy you a beer
+Tony Peterson THANK YOU!
Wow i never knew. Thank you for the info!
MÉTODO RESET FUSOR:
Lo probé en una Samsung 5010 y funciona perfectamente para hacer el RESET del FUSOR.
La secuencia completa es:
MENÚ
#1934
MENÚ
Entras al modo TECH y vas a DATA SETUP.
Luego eliges COUNTER RESET. Le das OK.
Eliges FUSOR y le das OK.
Y así todos los que quieras restear. (Tray 1, etc)
Finalmente apagas y vuelves a encender la máquina.
El contador del fusor estará en CERO.
Just tell me: what does it help that "el contador del fusor estará en CERO" if the fuser's mechanically damaged? Or the other way around: why would the fuser cause ANY problems (associated with a counter) unless it's worn or damaged?
thank you, i was getting repeated "chain" appearing marks on my papers, this took care of it.
Can we use the ethyl alcohol to clean the fuser instead of the isopropyl alcohol?
Yes but it could leave residues
RE CLP415-NW SAMSUNG LASER - I've endeavoured to release sticky label that broke off and perhaps impacted within the fuser area. A small piece was retrieved but there remains fragments that are preventing release. All other areas a clear. I've been tempted to unscrew top over to get better access. Would that help?
You have to remove the side panels first
Very helpful video. Uncomplicated and asy to follow.
Hello Viandant ! Thanks to help me . I have a CLP310, when the paper goes out the toner does not stick on the paper. Is this a problem of the heated roller ? Thanks a lot
+Guy Antequera yes, usually it's a problem related to the fuser rollers but may be also a defective toner cartridge
Please share how to upgrade firmware via usb in dead mode or in starting problem, samsung scx 6545,55n and also share shot codes like nvm initiliaze or hard reset in non working mode
Hello Viandant. Thanks for the video. I don't know why, but the toner seems not to properly attach to the paper. When i pass with finger it go away. Do you think it can be the fuser roller? Thank you
It's a typical error of the fusers, probably this is the problem
@@viandant5 thank you!
Hello, I have Samsung CLP300 colour laser printer and it gives me a paper jam just before the fuser it is happening when the paper is trying to enter the fuser and when I open the back cover I can see the paper all wrinkled and the toner on it is not developed. May I ask you how this can be fixed. The paper is not even entering the fuser and jams. Should I clean the fuser rollers or do something else? Thank you!
+undecided I think it's not a cleaning problem. verify if there is a foreign object near the fuser unit, may be the paper is dump, try change paper. check if the fusers are worn
I have a Samsung C1860FW and it gives me the message "Replace Fuser unit". I am not sure what to take out "Fuser" and whether its worn out or dirty and should be cleaned. Any suggestions? Thanks;.
It's difficult to remove the fuser unit, I think it's better to bring the printer to a repair center
should the pressure roller be completely smooth? mine is uneven, like small ripples in the rubber, is this normal or does it mean it's ruined? the roller looks clean but I still get horizontal (not vertical) lines when I print that seems to correspond to these uneven places on the roller. (ML-1660)
yes, the fuser roller must be smooth
Madame Traffic Jam
Thank you for the cleaning tips. My ML 1860 is clean, no marks on the fuse or elswere, but when printing, black spots are visible on the paper. My toner is 67 % full and really don't know what is the problem. The printouts of images are also kinda blurry and I noticed that my Samsung printer setting vanished with windows 10 updates lol
The problem vould be the toner cartridge, even if it's 67%. Check the transfer roller too
@@viandant5 Thanks, will do that. 👌
I have a CLP-415NW and Im getting blue spots on all pages that are the same size shape and position. I checked the toner cartridges and cleaned the rollers of excess toner. I don't see any defects in the green roller but the spots persist. What else do I need to check or clean? Thanks.
which is the distance of the blue spots? may be the problem is on the developer roller or on the charge roller
You suggested we ask questions. All of a sudden, I'm having having trouble with my Samsung laser printer. The light is green...and printer starts to work, but then stops...yet, I can find no stuck paper or other obvius problems. I need a new toner cartridge, btw, but with a little shake-up have been hanging in there with this puppy....until I can get to ordering the cartridge. Any idea what this might be? THANKS.
Which samsung? most of Samsung toner cartridges have chips, so it's useless to shake them if the chip is over. you can also try to clean the paper feed rollers with alcohol
Sir, could you please provide the online buying link of the fuser assembly unit of Samsung ML1676p
amazon, ebay, or search for "fuser depot"
do you have any videos on how to change clutch on samsung xpress printer?
So the red one is the pressure roller and the one above it is the heated roller? Do both rollers get cleaned?
Yes, you are right. If both are dirty, you have to clean both.
If the orange roller is damaged it needs to be replaced?
Yes there is no way to repair it
hello can guide me.... I have a samsung printer ml 2955dw that when you turn on the orange light on the panel is highlighted and a paper jam message appears inside the printer but it does not have any jammed paper. the fuser rollers is clean.
in this channel you'll find a video on what do to in case of false paper jam message
Hi guys, my C1860FW is scorching the paper down both sides? do i need to replace the fuser or is that built into each of the toners?
yes, it may be a problem related to the fuser. Look at the fusers. If the fusers are damaged the problem is there. If not, look at the drum. if there is toner on it, change the toner cartridge. That type of toner cartridge give lot of problems
viandant5 thank you, is there a Fuser built into each toner cartridge? Or just a main Fuser in the back of the unit?
there is only a fuser unit in the back of the unit
My samsung ML-1865 laser printer is printing a solid black print out. Changed toner still the same . cleaned pressure roller still same . Is their a solution please ?
Check the contacts between the printer and the toner cartridge. then, probably you have to change the high-voltage power-supply assembly,
I have a m2070Fw xpress, getting the fuser failure message #U1-2320, very frustrating as its just out of warranty. could cleaning them solve this problem?
the temperaturel of the fuser unit is abnormal, too high. try to turn the printer off then turn the machine on.
If the problem persists, remove the fuser unit. Check if the fuser connector is connected properly. Check if the thermistor is twisted or contaminated.
do you have a video on how to replace the pressure roller? the orange one? I have the piece but absolutely no idea of how to do it.
which printer?
@@viandant5 sorry, I was talking about CLP 360, should have told you.
@@diddy2703 No. I've done it. May be in the next weeks
I have replaced the fuser unit in my Samsung Xpresss C1860FW Printer but cannot reset the display. its still showing replace the fuser unit - help!!!
Hi,My printer's rubber roll is punctured, how can I fix it?new one is too expensive
it's not possible to repair a damaged fuser roller
@@viandant5 Thanks.then I'm going to throw it away
if my paper keeps jamming is this caused by the fuser ? Paper jams on the back side where the fuser is located. samsung SCX-4826FN
Yes, it may be caused by the fusers
thanks for you quick reply... i'm planning to do some research and replace the heat roller (upper and lower)
Paper struck and rolled on the fuser roller of my Samsung ML 1640 Laser Printer, cant prient any more . How to resolve the problem ?
if you can't remove the fuser unit, you can try to remove the paper one piece after another. make attention not to damage the rollers, use tools made of wood or plastic. not metal
How do I reset the fuser replacement light on the Xpress C1810W?
I think you have to enter Tech Mode
Press "Menu > Back > Left > Right > OK > Stop"
Hi , my Samsung ml 1660 printer make horizontal lines when printing how to fix that ? Thanks
always at the same distance? it depends on which is the distance, probably the drum of the toner cartridge
hy sir,
thank you for this video. I have an issue with one of my samsung -2161 printer, as of now i am getting random spots in page while printing page. What do now?
May be the toner cartridge is losing toner, on the recovery blade is damaged. clean the inside of the printer. check the fusers, if they are dirty try running a dozen of white pages
do you know if Samsung M2070 has a fuser inside it?
yes, there is a fuser unit
Thanks for Giving such usefull info about printers.
I have samusng ML-1676P MonoChrome LASER printer.
i found problem in Displaying RED light insted of Displaying GREEN light on starting of Printer with loaded Papers.
There is no effect on printing with RED light,
but i think printer may be heated without printing that's why the RED light displaying.
Give me solution for RED light insted of GREEN light.
is it a blinking red light?
viandant5 blinking on starting of printer only. after Red light is stable and print is continued.
Try another toner cartridge but it's strange, with the fix red light it should not work
ok. thanks..
Thanks for the video! I have cleaned the fuser rollers, belt and cartridges but I still get bad printout. I have emailed you a photo of the print. I hope you can help me. Thanks!
try to remove it with a wood or soft plastic spatula, there are no other ways unless you want to disassembly the fuser unit
I have samsung clx467 and on printing paper is rolling on pressure roller and is not coming out. What have I to do?
Try to clean the roller with alcohol, check if there are foreign objects along the paper path. try to change paper, may be the old paper is damp
@@viandant5 Thank for quick answer. I did it, but nothing changed. Paper si new, everthing is clear. I thing the roller surface is not more functioning. Any other idea?
@@velkytatko8879 It difficult to say without checking the printer. If nothing work may be there is something broken, the gear mechanism of the paper roller. I think that printer has to be repaired
Gracias, en vez de alcohol use thinner y se limpio mas rapido
Wtf
Samsung ml1676 laser printer Power on but no function what problem.
It could be the power supply
Hi my showing red light I am checking my fuser lamp is dead please guide the red light show showing is the reason lamp ?
Yes it could be the lamp
My printer ML-1666 , after command one page print out clearly but also one page jam in half out and half in ,how to relief the problem .
try cleaning the paper feed rollers with alcohol
viandant 5, my problem is that the copies come out of my printer with ripples on the bottom of the paper. HELP PLEASE
which printer? may be the feed rollers are worn or dirty, clean them with alcohol. verify if there are no foreign objects in the paper path
Hello. Do you have a link on cleaning using alcohol; is it a particular product that is readily available at any computer supplies shop?
isopropyl alcohol? it think you can find it easily searching with google
those links are only general rules on how to clean inside a printer
I have a C1860FW and the ink is printing powdery at the bottom. I can't figure out where the fuser is to clean it. Help?
In this model is not easy to clean without dismantle the printer. You can try opening the rear cover
My Samsung ML- 3310 d.does not response to print command but it prints configuration report.
Please solve.
Thanks
are ou sure the printer driver is correctly installed?
if u have a service manual of Samsung scx 4623fn pls share
no, I have no service manual
Hello Viandant !! The problem is solved, I changed the fuser ! I noted the sheets of paper were cold, now they get out warm and the toner sticks.
On the out of order fuser there are two thermal probes, is it possible to test them ?
+Guy Antequera the connections of the heating element? I think you can test them with a tester
+viandant5 No , on the fuser there are two thermal probes like KLICSON . Is it possible to see if they are good ? Thanks
+Guy Antequera the thermistor, its purpose is to check the temperature of the fuser. it's possible to check it wiht a tester
+viandant5 Ciao! Possiedo una Samsung clp-550n, prima mi faceva una riga verticale per foglio dei 4 colori: ho sostituito il tamburo ed ora non lo fa più... Ma è arrivato un altro problema: con la vecchia
fotounità dava il problema della riga ma i fogli uscivano bianco, invece con la nuova fotounità la stampa è senza righe ma i fogli vengono sporcati di grigio. Cosa può essere?
In una clx-3170fn avevo una immagine ghost della stampa precedente, ho cambiato fotounità e
questo problema scompare... Ma si evidenzai il problema delle macchie di grigio (in questo caso lievi) ai fogli. Ho sostituito anche la cinghia e ora stampa come nuova...
La domanda è: il mio problema delle pagine sporche di grigio, può essere dovuto alla cinghia
di trasferimento??? Eppure se metto la vecchia fotounità i fogli escono bianchi ma con la striscia dei 4 colori del toner.
Nella clx-3170fn con problema ghost quindi ho cambiato tamburo (fotounità) e risolto, mentre macchiava le pagine di grigio e cambiando anche la cinghia si è risolto.
Quel che mi interessa è per clp-550n: perchè il vecchio tamburo mi stampa le pagine regolarmente con sfondo bianco (ma essendo danneggiato fa anche la striscia verticale dei 4 toner) mentr eil nuovo tamburo giustamente ha risolto il problema dell'immagine ripetuta della stampa della pagina precedente ma ora però le pagine si sporcano di grigio uniformemente per tutto il foglio (o quasi)??? Grazie di cuore in anticipo per la risposta.
+Itanium IT sono macchine che cominciano ad avere un po di anni, è possibile che il nuovo tamburo fosse in magazzino da parecchio tempo e che sia scaduto o difettoso. se sostituendo il tamburo quel problema scompare è molto probabile che il tamburo sia il responsabile
may printer is samsang 4321 ns printing problams insart new cartege after print is not good pls. comet in sajetion
may be the cartridge is defective?
Sir my samsung ml1640 printer showing thermistor open cycle power error
How to over come from that issue
It's a fuser error. Probably you have to change the thernistor of the fuser unit. there are no reset procedures
mmmmm.. i have found this video by google after search some information about error #A3-3112 i obtain whiy a ML-1670.... i don't thinks what's the problems........ but i thinks i can trash this.....
My pinters rolling over have a lizard girdle how to make it out of the roller please say.
Without knowing the name of the printer is difficult to say, try to clean the rollers
hi. My hp laser printer smoking when paper gose out. any ideas?...:)
the paper is damp. change paper
thx
I have a samsung Xpress Color printer. The print is coming out with a blue line like this
___________
___________
down the center of the page. What can I do to fix??
which Samsung Express printer. a blue line vertical or horizontal?
Thank you for your reply. I don't know the model number. It is a color printer and uses C504S toners. The lines are horizontal and blue.
which is the distance of the lines? probably the problem is the cyan toner cartridge not the fusers
Maybe about an inch.
itt's the developer roller. the problem is the cyan cartridge
MY SCX 3405f have #1 2320 error code
i can not use it
remove the fuser unit and check if the fuser connectors are connected properly. Check if the thermistor is twisted or contaminated.
sir pressure roller hetter roller merged how to solved this problem in 1016 printer
I think you can only change the roller
@@viandant5 Sir the roller has already been replaced but still stuck
@@p.v.p.v.murugan7957 It stucks where? Does it stuck against the other roller or is it blocked?
@@viandant5 sir roller to roller merge
@@p.v.p.v.murugan7957 Did you check the gears? May it is blocked by a damaged tooth. Does the fuser melt with the other fuser?
the fuser unit contains a heat roller, & pressure rollers only. you are indicating there is more then ONE heat roller or pressure roller. There is not.
When I say there is more than one heat roller?
all the laser printer has fuser?
yes
Hi. I have a Samsung SL-C1810W printer. When I print a photo there are lot of visible vertical line entire width of the paper. I use original cartridges and current set is more than 1 years old after replacement since I do not print much. Is it a problem with the cartridges? What should I do. Below is a demo page printed which shows the vertical lines.
www.mediafire.com/view/q8wxgt757hr1h86/IMG_7225.JPG
I think it's a cartridge problem, probably yellow. I would try to change that cartridge.
Thank you for the reply. Is there anyway I can pinpoint which toner cartridge is faulty? and is there any expiring date for cartridges?
The second most probably culprit is the OPC drum. If you keep the toner cartridge in a dry place with a normal temperature, the expiration date is not important
The OPC drum is in the cartridge which is not replaceable isn't it? Is there any type color test page which I can print individual colors and find which cartridge is faulty?
the drum is into the toner cartridge. Print a page with a square cyan magenta black and yellow and look where is the problem. it may be the transfer unit too
Hello sir if possible make a video on format card repair power supply repair or scanner repair on chip level i wish to learn
i here make some sound in fucer unit
after change the fuser unit same problem arised
change the cartridge, if nothing works bring the printer to a repair center
Đổ hộp mực 12A chỉ với 1 chiếc kéo th-cam.com/video/UHt720xcOLw/w-d-xo.html
Hộp mực 12A giá 100k th-cam.com/video/b-9UurlqyYU/w-d-xo.html
My samsung printer errer #U1-2320 TURN OFF THEN ON.printer is not work please tel me please
printer model is SCX-4321NS
it's an error of the fuser unit. Turn the machine off and on. Check if the fuser connector is connected properly. Check if the thermistor is twisted or contaminated.
Privew nhi aarha h
Thank you Leonel Messi!!
Porra eu estou no BRASIL, vocês estão falando outra língua..Que merda.
There are CC portuguese subtititles if you want
what must I do if the fucking paper is stuck in the fuser unit???
You have to remove the sheet using a wood ot soft plastic spatula, there are no other way if you don's want to disassemble the fuser unit
I have a ML 2545 Laser printer that shows paper jam, I have removed all paper but still shows paper jam any ideas?
may be a paper sensor, here your find some methods. th-cam.com/video/yXWgx8m-gY0/w-d-xo.html
I have a Samsung scx4623fn printer.when it starts after initializing a error shown
"error #02-000 turn off then turn on the printer" .
pls help me
Power the printer off and then power it on again. try to replace the toner cartridge. if it does not work, the problem is caused by a bad fuser unit.