Good ides I liked that you insulated the with kapton before adding the magnet wire. Most guys you see doing these hacks never do this and it's very dangerous not to. So thumbs up 👍 from me for that alone 👍🇮🇪💚🙏🏻
Не надо. :) Трансформатор, явно не рассчитанный на ток в 1,4 А. Транзисторы без радиаторов, SMD резисторы на мизерные токи и т.д. При мощности лампочки в 20 Вт и высоком напряжении её питания эти токи были не значительными. А вот чтобы запитывать трансформатор, на выходе которого висит нагрузка в 1,4 Ампера, многие элементы схемы придётся пересчитывать.
Boa noite professor e amigos. Tenho algumas lâmpadas dessas aqui e procurava um bom uso para elas, e achei. Ainda mais com a amperagem que apareceu na carga da bateria. Por gentileza, qual o calibre do fio usado na nova bobina? Continue e forte abraço do Brasil.
Bom dia. No diagrama mostra uma bobina com dois pinos e um transformador. Não encontrei essa configuração em nenhuma das minhas lâmpadas. Na maioria tem transformador de 4 pinos e uma bobina toroidal. Dá para fazer com esses componentes? Não conheço muito de bobinas, por isso pergunto. Obrigado pela atenção.
Boa noite. Para usar com a lâmpada 12v do vídeo, necessita-se de no mínimo 0,600A,; o motor, desconheço; e na carga da bateria foi mostrado 1,4A, se não me engano. Agora, só conhecendo melhor o circuito e medindo-o, para sabermos a corrente dele. Forte abraço do Brasil.
With smps we have two sides, ac side and DC side..simply saying primary side and secondary side..this is fake..I don't see even the MOSFET and applo here
Single Mosfet Powerful Tesla Coil Circuit
th-cam.com/video/fIWaYa11Ax8/w-d-xo.html
Allahım
Good ides I liked that you insulated the with kapton before adding the magnet wire. Most guys you see doing these hacks never do this and it's very dangerous not to. So thumbs up 👍 from me for that alone 👍🇮🇪💚🙏🏻
Очень интересное применение. Надо проверять длительное время.
Не надо. :) Трансформатор, явно не рассчитанный на ток в 1,4 А. Транзисторы без радиаторов, SMD резисторы на мизерные токи и т.д. При мощности лампочки в 20 Вт и высоком напряжении её питания эти токи были не значительными. А вот чтобы запитывать трансформатор, на выходе которого висит нагрузка в 1,4 Ампера, многие элементы схемы придётся пересчитывать.
Me gustó el vídeo excelente esperó que hayan otros mejores
Boa noite professor e amigos. Tenho algumas lâmpadas dessas aqui e procurava um bom uso para elas, e achei. Ainda mais com a amperagem que apareceu na carga da bateria. Por gentileza, qual o calibre do fio usado na nova bobina? Continue e forte abraço do Brasil.
السلام عليكم.
بحاثة فضولي نجام هائل! استمر! افكار مبدعة مرنة! فضول علمي ممتاز!
Presente: Cordial Saludo desde Jalisco Mx Siempre Pendiente.
Super. Pozdrawiam serdecznie
the voltage drop after connecting the load it's not regulated without feedback there is no optocoupleur used.
How to put optocoupler
@@thawzinkhant1759 in the ccfl bulb they put an oscillator based on tow transistor or more with no feedback
@@labiadh_chokri ya we can see there's one optocoupler in every AC-DC-AC-DC charger circuits but how to connect ?
@@thawzinkhant1759 in general it's connected to the oscillator cercuit to vary the width of the pulse. It used with the voltage reference tl431.
@@labiadh_chokri ok I see
Thank for sharing. Like it
Bom dia parabens muito bom
What is the guage of the copper wire is being used to wind the extra windings?
What is the diameter of the wire you used
0.3mm
Good idea don't worry your like will be credited after experiment
Use double diode to get more efficiency..
Nice idea, Like it
Молодец все четко 👍
Thanks
Bom dia. No diagrama mostra uma bobina com dois pinos e um transformador. Não encontrei essa configuração em nenhuma das minhas lâmpadas. Na maioria tem transformador de 4 pinos e uma bobina toroidal. Dá para fazer com esses componentes? Não conheço muito de bobinas, por isso pergunto. Obrigado pela atenção.
You are right that the transformer has four pin, but only two pins are connected internally. Desolder and find those pins.
Thank you for your comment
Woaaaaaaw ,, amazng bro
Good work.
Thank, very good.
Está bien ese circuito 👍 que amperaje entrega?
Boa noite. Para usar com a lâmpada 12v do vídeo, necessita-se de no mínimo 0,600A,; o motor, desconheço; e na carga da bateria foi mostrado 1,4A, se não me engano. Agora, só conhecendo melhor o circuito e medindo-o, para sabermos a corrente dele. Forte abraço do Brasil.
Woow 👍👍👍thank you .
Good Job.
good!
Thanks!
love eletronics
It works...😮 ,good
what is the diameter of the wire 0,..? mm
Not sure it coult hold ~1Amp for a long time to charge the battery 🤨
You need Schottky diode sr360
А как насчёт нагрева транзисторов
Кто такими мелочами тут заморачивается?
How many amps can we get
This circuit maximum A how much
No super,👍👏
Wire thickness?
Like Brasil 🇧🇷🇧🇷🇧🇷
این یک دروغ بزرگ است.من وقتی خروجی ها را به هم وصل کردم ترانزیستور لامپ منفجر شد
👏👏👏
❤❤❤❤❤
There are only few cfl today...
Mostly used todays are LED's ..
Try making that one someday instead of that cfl
Too many outdated CFL circuits are in every home. It's good to find a way to reuse them
is the output electrocuted?
Nope, the secondary coil is insulated
Hi💜
apakh in berlaku untuk Semua jenis lampu LHE
Yes.
@@adolfbenit9217 terimakasi jawabanya.soly q membutuknay
With smps we have two sides, ac side and DC side..simply saying primary side and secondary side..this is fake..I don't see even the MOSFET and applo here
Bhai bilcul Kam Nani karta
Salam aleykum
That's not how a smps should work, don't try this.
Только такие лампочки остались разве что в Индии)))
👏👏👏👏
👍👍👍 نريد مثل هذا العمل على دائرة النيون ليد إذا كان ذلك ينجح فيها.
good idea but is there any temperature in the transformer while charging the battery ??
For 12 volt turns...?
14turn