Great vid! wondering can you operate one solenoid at different amounts of current in one circuit? I'm guessing this would be done by some parrell circuit of some sort, or a diff. load voltage?
The solenoid is rated for 12 volts; at higher voltages, you might fry it, and at lower voltages, it might not move at all. Why would you want to operate a solenoid at different amounts of current anyway?
so if the power is on all the time the solenoid would be out yes then when power is cut off it springs back. can you keep a contants 12v feed to it without it blowing up 12v mine is i want to know if the 12v in is present for lets say 3hrs or so would it be ok
It can push with about 0.4 N of force. You're going to need to measure how much force your can needs. A servo motor may work better if you need more force.
Nice video,i'm trying to figuire out why the solenoid mounted on my car starter motor doesn't work, the solenoid gets warm so i'm guessing the coil inside is getting hot but for some reason the plunger won't pop out.I tried slapping it around with a hammer but to no avail. Even though they're irreparable,i'd still like to know what's wrong.Thanks.
Hi Dave I’m look at building something using basically the same solenoid and a PIR. So I have a micro PIR sensor that momentarily switches on and off for around 2-5secs running off a CR2 battery 🔋 what do I need in between the PIR & solenoid? I.e diode and also need a current limit of 100ma. If you can help me out
I assume that you can make the PIR and solenoid share a ground. You'll want an N-channel MOSFET. It can take a low-voltage, low-current signal and switch a high-voltage, high-current line on and off. Look at "Simple Solenoid Drivers" on www.electronicdesign.com/industrial-automation/what-s-best-way-drive-solenoid for the basic idea.
Not the one in the video. The force that is required will vary (different surfaces will have different amounts of friction, for example), but even in ideal conditions, the solenoid that I used won't push a whole tennis ball that high.
@@raymetal7 More like 1.3 cm in ideal circumstances. I previously measured the solenoid to push with at most 0.50 N. Let's assume that it exerts this force constantly while the plunger is moving, and let's assume that the ball stays in contact for the maximum travel of 0.010 m. That's 0.0050 J of work (force * distance). Convert that to gravitational potential energy (mass * gravitational acceleration * height). A standard tennis ball weighs at least 0.057 kg. Assuming 9.8 m/s^2 acceleration of gravity, if we solve for the height, that gives us 0.0090 m of height ([0.0050 J]/[9.8 m/s^2]/[0.057 kg] = 0.0090 m). Of course, that's going straight up; if the ball is rolling up a 45° ramp, then we can divide that by sin(45°) to get 0.013 m or 1.3 cm. Again, this is assuming no friction, a constant force from the solenoid, and contact between the ball and the plunger for the plunger's full range of travel. Of course, if you got a stronger solenoid, then the ball would move farther.
@@raymetal7 Oh, and this assumes that the ball doesn't roll. We already assumed no friction, so the ball won't roll as long as the force is applied perfectly in line with the ball's center of gravity.
Can you please mention the sizea nd Force of the Solenoid? Also the site from where you buy this? I need a solenoid of almost 15mm dimension and upto 20N Force.
I got the one in this video on Amazon: www.amazon.com/dp/B008LTHYLA It has a holding force of 4 N, but in my experimentation, it only pulled with about 0.75 N. If you need a lot of force, you should also consider pneumatics or a servo motor.
Hello David. I’m building a possum trap. Cage type. As a kid I made traps where a possums weight on a ramp tripped a guillotine type trap door that shut behind animal. Now I want a electric trip where I still use a ramp which taps a micro switch that sparks the coil/solenoid pulls the pin that drops the door. But how do I stop power after trap has tripped? Power would have to be switched off to avoid burning out coil.
You're looking for a monostable multivibrator. Here's a version that doesn't use a 555 chip: www.falstad.com/circuit/e-multivib-mono.html Here's one that does: www.falstad.com/circuit/e-555monostable.html
@@wecsam Thanks for the reply... I will just use another Micro switch! First one (N/O) will be on the platform and trigger the Solenoid. and gate drops The second Micro switch (N/O) on a roller arm will be on the dropping door and when the door has dropped the door will run off the switch and will "open" the circuit. Therefore cutting power to coil.
For something as heavy as a tennis ball, you'll probably have a much easier time with a pneumatic piston. These small solenoids can't produce a lot of moving force.
Hey Bud, Will this ^ solenoid be able to push the button on a typical torch lighter. I'm building a miniature castle with a fire breathing dragon and I would like to work the lighter button remotely, Thanks, hope you can give me the magic answer ...
how fast is can this actuate? planning a 3d printed paintball marker, and trying to come up with ways to get something to actuate the ball valve letting air to escape and send the paintball flying. I am trying to get to atleast 5 balls a second if that info helps.
In this video, the plunger takes about 2 frames to move its full range. At 30 FPS, that is about 0.067 seconds. I would probably need a high-speed camera to get a more precise measurement.
I'm looking at these to activate a pull pin on a rc 1/10 winch can I just hook up the positive to a switch turn on stays pulled in until switch is turned off then springs back then opersite way wind winch in 🤔
Yes, the plunger stays pulled while power is on, and a spring pushes it back when the power is cut. A switch would work great for controlling this. However, just be aware that it doesn't pull with much force; I am not sure how much force your pull pin needs, but you might need a bigger solenoid.
@@wecsam does it matter wich wire I would use thinking about a servo too but need to convert it to two wire but I dunno if it self level modding to two wires 🤔
@@Lee-At-Green-Pheonix-Rc I recommend getting a force meter to figure out how much force you actually need and then using that to decide on a solenoid or servo.
You could add a heatsink to the diode, but if it's getting too hot, double-check that you're using the correct voltage for it. Check that it is drawing the amount of power that the manufacturer specified. You could also try another solenoid in case that you have a defective one. I don't have the exact diode model anymore, but any 1N4*** should work. It only has to block Vcc.
That's going to depend on the switch and the solenoid. The solenoid in the video was not able to push or pull with much force; it is not strong enough to push any switches that I've used. You would have to make sure that your solenoid is strong enough to push your switch. It might be easier just to use a servo motor; some of those have a lot of torque, and there are plenty of designs on the Internet that mount servo motors to light switches. I have a video where I show just that: th-cam.com/video/m3pA422aRlg/w-d-xo.html
After the current stabilizes, the solenoid draws about 4 amps. It does get hot, but I do not know whether it would fry. Perhaps that could be its own video.
+kawi21 The solenoid is an inductor, which means that the current cannot immediately flow at its maximum. When an inductor is discharged, it's like an open circuit. When it is charged, it is like a short circuit. The solenoid's magnetic field, therefore, won't be at full strength until the inductor is fully charged and the current is flowing at its maximum.
You need to make all your grounds are connected. This normally happens when people are using external power and something like an arduino but have not connected the grounds together. Also listen to David. Make sure your power supply is supplying 12V AND the current needed by the solenoid.
A solenoid is an inductor, which means that it draws very little current at first and then gradually draws more current. That said, real solenoids have some resistance. This one did not draw more than 4 amps while I was using it.
hi thank you for this awesome video. can you please guide me to use what kind of solenoid and battery with volts and other specs that can produce 50N and 100N of force.
+Be Like Bill Solenoids have two difference force ratings. The force that is usually listed is the holing force, which refers to the amount of force that you would have to exert in order to pull the plunger in the reverse direction when the solenoid is powered. (In fact, I just realized that the video description is a little ambiguous. I'll update it.) The force that the solenoid can exert on another object is usually much less than the holding force; in this case, it was less than 1N. If you need to exert 50N to 100N of force on another object, consider using a pneumatic piston instead.
Hi, How can ı make a full automatic selenoid engine? Forward-back-forward-back like a tatto machine? I want to make a pen for working on copper plate. For dotted texture.
I'm not sure how tattoo needles work, but a solenoid like this one probably won't be fast enough. An electric motor with a slider-crank mechanism might be a better choice.
It can push with about 0.4 N of force. How much weight that translates to depends on how you're using the solenoid. If you're pushing horizontally across a surface, you'll need to know the coefficient of friction between the object that's being pushed and the surface.
hello im trying to test my solenoid actuator but it wont work when i connected directly to 12v battert.. can you explain why? and how the actual way to test it and make it work?
What sort of 12V battery are you using? Some smaller batteries may not be able to supply enough current to power the solenoid. What proximity sensor are you using? If it has a simple on/off output, you can just connect that output to an NPN transistor or MOSFET on the ground side of the solenoid.
David Tsai yes im using the 12v dc battery the smaller one.. oh so its not enought current? I need to try using generator? I use npn inductive proximity sensor so if i use transistor/mosfet i dont actually need relay&base to connect my sensor and the solenoid?
+nadyrahh slvee Connect the output of your proximity sensor to the base of your NPN transistor. Connect the ground of the solenoid to the collector of the NPN. Connect the emitter of the NPN to ground.
I've been curious about the possibility of using a type of actuator like this to act as a firing pin for a firearm that I've considered building. I figured that it would only require a momentary contact switch for the actual trigger, so it could be extremely sensitive. It looks like the model that you show here might not provide enough force to the firing pin. You also need a certain speed hitting the firing pin -- a slow large force will not necessarily set the primers off.
I've never operated a firearm, but I can say that this model solenoid could not produce enough force to move a light switch. You would probably need a bigger solenoid.
Never operated a firearm before? Wow... I've *heard* about people like that, but I don't think I've ever actually met one. :) Oh... You're in New Jersey... I guess that explains it... :)
+jossesphere Uxcell a12022000ux0201 4N Push Type Open Frame Solenoid Electromagnet Actuator, DC 12V, 10 mm www.amazon.com/dp/B008LTHYLA/ref=cm_sw_r_cp_apa_OUy7xbNQJ3MSJ
+Let's Talk Retro The polarity of the solenoid doesn't matter. The plunger moves the same way either way. You should connect one to + and one to -, though.
I enjoyed this video so much! I came to see the solenoid but you were more fun. Keep on doing what you do!
I never thought about using a flyback diode, thx!
Yes indeed..
I am making some laser game rifles and was thinking of using linear solenoids as a kind of recoil tool. This demonstration was quite helpful.
thanks for the demo bro! This video swayed me to buying an electromagnet for my project
Did you ever do anything else with the noid?
Great vid! wondering can you operate one solenoid at different amounts of current in one circuit? I'm guessing this would be done by some parrell circuit of some sort, or a diff. load voltage?
The solenoid is rated for 12 volts; at higher voltages, you might fry it, and at lower voltages, it might not move at all. Why would you want to operate a solenoid at different amounts of current anyway?
@@wecsam I'm envisioning using a solenoid as an actuator for a lever arm, that may move different things depending on its strength.
so if the power is on all the time the solenoid would be out yes then when power is cut off it springs back. can you keep a contants 12v feed to it without it blowing up 12v mine is i want to know if the 12v in is present for lets say 3hrs or so would it be ok
Can you keep the connection on to keep the bolt extended out the entire time until the connection is broken then it retracts.
Would this 5v solenoid have enough force to push the nozzle of a spray paint can down? Thanks for your demonstration
It can push with about 0.4 N of force. You're going to need to measure how much force your can needs. A servo motor may work better if you need more force.
What is the current this solenoid takes? I suspect about 1A.
Which solenoid would you recommend with smaller current (
Is the diode used on AC and DC solenoid actuators?
Nice video,i'm trying to figuire out why the solenoid mounted on my car starter motor doesn't work, the solenoid gets warm so i'm guessing the coil inside is getting hot but for some reason the plunger won't pop out.I tried slapping it around with a hammer but to no avail. Even though they're irreparable,i'd still like to know what's wrong.Thanks.
Hi Dave I’m look at building something using basically the same solenoid and a PIR. So I have a micro PIR sensor that momentarily switches on and off for around 2-5secs running off a CR2 battery 🔋 what do I need in between the PIR & solenoid? I.e diode and also need a current limit of 100ma. If you can help me out
I assume that you can make the PIR and solenoid share a ground. You'll want an N-channel MOSFET. It can take a low-voltage, low-current signal and switch a high-voltage, high-current line on and off. Look at "Simple Solenoid Drivers" on www.electronicdesign.com/industrial-automation/what-s-best-way-drive-solenoid for the basic idea.
Hi there, not sure if you are still active here.. May I know what is the model that you use for the linear actuator?
Hi David
What is the easiest way to make a solenoid recoil?
This solenoid has a little spring in it that retracts the plunger when power is cut.
do you think the solenoid is powerful enough to push a tennis ball up a 30 cm ramp which makes a 45 degree angle with the floor?
Not the one in the video. The force that is required will vary (different surfaces will have different amounts of friction, for example), but even in ideal conditions, the solenoid that I used won't push a whole tennis ball that high.
@@wecsam how high would it push it then? 10 cm? Let's say the surface has minimal friction.
@@raymetal7 More like 1.3 cm in ideal circumstances. I previously measured the solenoid to push with at most 0.50 N. Let's assume that it exerts this force constantly while the plunger is moving, and let's assume that the ball stays in contact for the maximum travel of 0.010 m. That's 0.0050 J of work (force * distance). Convert that to gravitational potential energy (mass * gravitational acceleration * height). A standard tennis ball weighs at least 0.057 kg. Assuming 9.8 m/s^2 acceleration of gravity, if we solve for the height, that gives us 0.0090 m of height ([0.0050 J]/[9.8 m/s^2]/[0.057 kg] = 0.0090 m). Of course, that's going straight up; if the ball is rolling up a 45° ramp, then we can divide that by sin(45°) to get 0.013 m or 1.3 cm. Again, this is assuming no friction, a constant force from the solenoid, and contact between the ball and the plunger for the plunger's full range of travel.
Of course, if you got a stronger solenoid, then the ball would move farther.
@@raymetal7 Oh, and this assumes that the ball doesn't roll. We already assumed no friction, so the ball won't roll as long as the force is applied perfectly in line with the ball's center of gravity.
hey ,Which swg wire u have used for this ?And Can u tell how to calculate the dimensions, number of turns, wire diameter to pull "500g". Thanks.
Can you please mention the sizea nd Force of the Solenoid? Also the site from where you buy this? I need a solenoid of almost 15mm dimension and upto 20N Force.
Any idea from where I can buy such small solenoid with such a force
I got the one in this video on Amazon: www.amazon.com/dp/B008LTHYLA
It has a holding force of 4 N, but in my experimentation, it only pulled with about 0.75 N. If you need a lot of force, you should also consider pneumatics or a servo motor.
It is possible to make this baby high speed ?
Hello David. I’m building a possum trap. Cage type. As a kid I made traps where a possums weight on a ramp tripped a guillotine type trap door that shut behind animal.
Now I want a electric trip where I still use a ramp which taps a micro switch that sparks the coil/solenoid pulls the pin that drops the door.
But how do I stop power after trap has tripped?
Power would have to be switched off to avoid burning out coil.
You're looking for a monostable multivibrator.
Here's a version that doesn't use a 555 chip: www.falstad.com/circuit/e-multivib-mono.html
Here's one that does: www.falstad.com/circuit/e-555monostable.html
@@wecsam Thanks for the reply... I will just use another Micro switch!
First one (N/O) will be on the platform and trigger the Solenoid. and gate drops
The second Micro switch (N/O) on a roller arm will be on the dropping door and when the door has dropped the door will run off the switch and will "open" the circuit. Therefore cutting power to coil.
@@byLokie Good thinking. That works, too.
David Tsai Thanks. Simple enough.
Hello sir i want to push a 100 kg weight bar like that colgate box cross section area how much capacity of linear solenoid actuator i have to use ?
A 100-kilogram bar the size of the toothpaste box? Did you mean grams?
what type of solenoid can be used for a ‘launcher’ of a tennis ball?
For something as heavy as a tennis ball, you'll probably have a much easier time with a pneumatic piston. These small solenoids can't produce a lot of moving force.
Hey Bud, Will this ^ solenoid be able to push the button on a typical torch lighter. I'm building a miniature castle with a fire breathing dragon and I would like to work the lighter button remotely, Thanks, hope you can give me the magic answer ...
how fast is can this actuate? planning a 3d printed paintball marker, and trying to come up with ways to get something to actuate the ball valve letting air to escape and send the paintball flying. I am trying to get to atleast 5 balls a second if that info helps.
In this video, the plunger takes about 2 frames to move its full range. At 30 FPS, that is about 0.067 seconds. I would probably need a high-speed camera to get a more precise measurement.
David Tsai no need man, those calculations are good enough for me. Thanks!
I'm looking at these to activate a pull pin on a rc 1/10 winch can I just hook up the positive to a switch turn on stays pulled in until switch is turned off then springs back then opersite way wind winch in 🤔
Yes, the plunger stays pulled while power is on, and a spring pushes it back when the power is cut. A switch would work great for controlling this. However, just be aware that it doesn't pull with much force; I am not sure how much force your pull pin needs, but you might need a bigger solenoid.
@@wecsam does it matter wich wire I would use thinking about a servo too but need to convert it to two wire but I dunno if it self level modding to two wires 🤔
@@wecsam or recommend a bigger solenoid that not too bulky smaller the better
@@Lee-At-Green-Pheonix-Rc I recommend getting a force meter to figure out how much force you actually need and then using that to decide on a solenoid or servo.
How arrest heat and which type of diode are you using this?
You could add a heatsink to the diode, but if it's getting too hot, double-check that you're using the correct voltage for it. Check that it is drawing the amount of power that the manufacturer specified. You could also try another solenoid in case that you have a defective one.
I don't have the exact diode model anymore, but any 1N4*** should work. It only has to block Vcc.
Hey David, I need your help. I wanna know can I use it to push a modular electrical switch?
That's going to depend on the switch and the solenoid. The solenoid in the video was not able to push or pull with much force; it is not strong enough to push any switches that I've used. You would have to make sure that your solenoid is strong enough to push your switch.
It might be easier just to use a servo motor; some of those have a lot of torque, and there are plenty of designs on the Internet that mount servo motors to light switches. I have a video where I show just that: th-cam.com/video/m3pA422aRlg/w-d-xo.html
@@wecsam Thanks David!
May I know the specifications of the Solenoid that you used in the video?
@@harenderjeetarora7508 You can find them on the original item page here: www.amazon.com/dp/B008LTHYLA/
interesting, what is the valúe of that diode?
It's a standard 1N5408 diode.
this looks like more than a 10mm stroke.will this pull a 3lb object ?
+Rob M What direction are you pulling it in? Is it up and down or left and right?
left right, a trigger rated at 3lb break
Do you have a link on ware I can find this?
What happens if you leave the power on? Will it fry the solenoid or reduce wattage drawing?
After the current stabilizes, the solenoid draws about 4 amps. It does get hot, but I do not know whether it would fry. Perhaps that could be its own video.
this is amazing video
can you share with us the details of your snubber diode? is it the same as using a rectifier diode? thanks!
+Jodie Trinity Yeah, I just used a cheap rectifier diode.
cool, thanks for the advice and enjoyable video!
hello David. how we can make it by 220 v. i want to know exactly how the danfoss solenid wotk whit 220 v?
The solenoid in this video uses DC. Just get an AC adapter that works with your 220V source.
what would cause a 1 second or so delay in the solenoid after 12v is applied?
+kawi21 The solenoid is an inductor, which means that the current cannot immediately flow at its maximum. When an inductor is discharged, it's like an open circuit. When it is charged, it is like a short circuit. The solenoid's magnetic field, therefore, won't be at full strength until the inductor is fully charged and the current is flowing at its maximum.
I need a help.. If a solenoid is conected to a 12 v suply it continuously shutters..how to solve that? Any sugestions..
Make sure that your power supply can handle the current that the solenoid needs.
You need to make all your grounds are connected. This normally happens when people are using external power and something like an arduino but have not connected the grounds together. Also listen to David. Make sure your power supply is supplying 12V AND the current needed by the solenoid.
Great video.
By the way, how much current does a solenoid this size drag?
A solenoid is an inductor, which means that it draws very little current at first and then gradually draws more current. That said, real solenoids have some resistance. This one did not draw more than 4 amps while I was using it.
hi thank you for this awesome video. can you please guide me to use what kind of solenoid and battery with volts and other specs that can produce 50N and 100N of force.
+Be Like Bill Solenoids have two difference force ratings. The force that is usually listed is the holing force, which refers to the amount of force that you would have to exert in order to pull the plunger in the reverse direction when the solenoid is powered. (In fact, I just realized that the video description is a little ambiguous. I'll update it.) The force that the solenoid can exert on another object is usually much less than the holding force; in this case, it was less than 1N. If you need to exert 50N to 100N of force on another object, consider using a pneumatic piston instead.
Hi,
How can ı make a full automatic selenoid engine? Forward-back-forward-back like a tatto machine?
I want to make a pen for working on copper plate. For dotted texture.
I'm not sure how tattoo needles work, but a solenoid like this one probably won't be fast enough. An electric motor with a slider-crank mechanism might be a better choice.
how many battery or volts should i use to run a 12v solenoid?
+Ajit zone Use a 12V battery or eight 1.5V batteries to power a 12V solenoid.
David Tsai i used 8 1.5v batteries. but it didnot work. 12v battery costs alot. any other way?
+Ajit zone Get yourself a multimeter and see whether you are actually getting 12V.
12Vplts...
Isn't that obvious? It said that in it's name: 12v solenoid, 12v = 12 volts why do people keep asking stupid questions?
How much weight it can push
It can push with about 0.4 N of force. How much weight that translates to depends on how you're using the solenoid. If you're pushing horizontally across a surface, you'll need to know the coefficient of friction between the object that's being pushed and the surface.
very good thanks. how to make it?
DC 12V 2A Push Pull 10mm 20N what diode do i need?
Any old diode that can block 12V will suffice. A 1N4001, for example, can block up to 50V and will work fine.
@@wecsam thank you buddy
DC 12v .82A my solinoid gets hot after 5 seconds when kept on can diode will solve the problem?
cool. I really need this..
hello im trying to test my solenoid actuator but it wont work when i connected directly to 12v battert.. can you explain why? and how the actual way to test it and make it work?
and i want to connect the input of actuator to proximity sensor if you dont mind can you help?
What sort of 12V battery are you using? Some smaller batteries may not be able to supply enough current to power the solenoid. What proximity sensor are you using? If it has a simple on/off output, you can just connect that output to an NPN transistor or MOSFET on the ground side of the solenoid.
David Tsai yes im using the 12v dc battery the smaller one.. oh so its not enought current? I need to try using generator? I use npn inductive proximity sensor so if i use transistor/mosfet i dont actually need relay&base to connect my sensor and the solenoid?
David Tsai and if i use bjt/moafet which leg do i connect with the gnd of solenoid?
+nadyrahh slvee Connect the output of your proximity sensor to the base of your NPN transistor. Connect the ground of the solenoid to the collector of the NPN. Connect the emitter of the NPN to ground.
I've been curious about the possibility of using a type of actuator like this to act as a firing pin for a firearm that I've considered building. I figured that it would only require a momentary contact switch for the actual trigger, so it could be extremely sensitive. It looks like the model that you show here might not provide enough force to the firing pin. You also need a certain speed hitting the firing pin -- a slow large force will not necessarily set the primers off.
I've never operated a firearm, but I can say that this model solenoid could not produce enough force to move a light switch. You would probably need a bigger solenoid.
Never operated a firearm before? Wow... I've *heard* about people like that, but I don't think I've ever actually met one. :)
Oh... You're in New Jersey... I guess that explains it... :)
+Grumpy OldMan It sure does.
Yeah, up there in the non-free states, they only allow the criminals and cops (not necessarily two separate groups) to be able to protect themselves.
+Grumpy OldMan I guess so.
Hey David, do you happen to know what model that solenoid is?
Really educational vid :)
+jossesphere Uxcell a12022000ux0201 4N Push Type Open Frame Solenoid Electromagnet Actuator, DC 12V, 10 mm www.amazon.com/dp/B008LTHYLA/ref=cm_sw_r_cp_apa_OUy7xbNQJ3MSJ
A 4N will push alot more than I thought !
Where I can buy those?
I got them on Amazon.com. Search for the seller "Uxcell."
Thanks!, Can you please tell me the serial #?
Can I ask a stupid question, which way round do you wire the solenoid or does it not matter as long as one is + and one is - ?
+Let's Talk Retro The polarity of the solenoid doesn't matter. The plunger moves the same way either way. You should connect one to + and one to -, though.
Thanks David.
doesn't matter.
I want to use on or 2 on a locking steel box in my truck.
thats literally a minecraft piston
This is not linear actuator only top bottom or left right position.. where is the middle position???
is there a automatic version
Puedes compartir el diagrama de conexión
Lol, great video!
so funny :)
It's too hot in my solenoid
You could have showed us the entire set up