LEDs require a 12v DC source. Your amplifier emits an alternating current or ac. This will effect how the load on the amp is received, and will cause damage to the components. Please stop telling people to do this.
well im not very knowledge in eletronics but i know some, so there is a way to kill your amp by doing this, using AC (speaker works with Alternate Current, leds are designed to work with DC) with leds, youre forcing voltage into led in a way they are not meant to have, doing that any led in the strip may fail and go into short circuit and then kill your amplifier. Im thinking that theres is some workaround to this, adding some other diodes into the negatives and RGB inputs on the strip, or just using some resistors in the same way to limit the voltage that goes to the leds, dont ask me for schematics bcuz i dont know.
HEY EVERYONE DON'T TRY THIS CUZ IT CAN BLOW YOUR AMPLIFIER OR HOME THEATER JUST TAKE A 1K CAPACITOR AND CONNECT IT TO LED STRIP+ THEN CONNECT - WIRE TO LED STRIP AND ANOTHER WIRE (+) TO THE OTHER SIDE OF THE CAPACITOR THEN CONNECT IT TO YOUR SUB WOOFER OR SPEAKER 👍
1: you make it look like more difficult 2: frome amplifier you get less power when it's normal volume, so you have turn volume a lot higher to get enough illumination * putting led directly not gonna helps you * just simply buy two amplifier one for speaker one for led There can be other alternative but At least you don't have to turn higher volume and 100% sure that your amplifier don't blow ✌
This is like the kind of thing that i would love to do but i just know that i will never bother learning because of the danger of fire lol. I wouldn't trust myself to not mess it up xd
Bigger resistor, you only need a tiny amount of power from the signal and 600w will blow these up. (I think) if you have an amp that does 600w @ 8Ω then it will do 300w @ 16Ω, 150w @ 32Ω, ...... 16w @ 128Ω, 8w @ 256Ω - measure the resistance of your strip and make up the difference in impedance with another resistor inline to bring it up to the correct value. I would check the rating of your amp first, if it is actually 600w at 8Ω or 4Ω or whatever, from there you can extrapolate where you need to get to.
Remember the Radio Shack light organ boxes, where each of the 3 colors operated on the different sound levels? That's what I want to learn how to properly make.
@@Speakershocker kannst du mir erklären warum hier der Verstärker kaputt geht? Kenne mich jetzt nicht wirklich aus aber wer nicht fragt bleibt dumm... Wenn jetzt theoretisch die Gesamtimpedanz über der Minimalimpedanz des Verstärkers liegt (z.B nur die LEDs ohne Boxen) fährt der Verstärker doch auch nicht ins Clipping. Dem is dass doch egal oder? Oder weil der Strom jeweils immer nur ne halbe Periodendauer fließt weil die LEDs während der negativen Amplitude sperren? Was schädigt hier dem Verstärker? Danke
Hi Hifi, it was the same and the ohm is adjusted to the speaker, performance when recording and transmitting, it's no use putting up a series of LEDs equipped with resistors, an LED works at about 3v, so you not only damage the hifi, but it can also cause a short circuit because there is no switch on it!
@@Kanoshe Amplifier is for speakers with definitive ohms and if you add another appliance like leds than mosfets or chip may burn up from excess current
Oh Junge 🤦♂️ macht das bitte nicht nach, das zieht eurem Verstärker nur Leistung und senkt den Widerstand des Lautsprechers am verstärker was ihn zerstören kann.
Das Stimmt Nur bedingt! Dem Verstärker ist das erstmal egal die LEDs mit widerstand haben einen VIEL höheren widerstand (je nach länge) als das sie schaden anrichten könnten. ABER Ein Problem ist eher das der Verstärker ungleich belastet wird. LED Lassen Strom nur in eine Richtung Durch Das heist die belasten auch nur bei einen positiven Impuls NICHT aber bei dem negativen. Dafür wäre eine Gleichrichtung mit elko nötig) Das ist aber MEISTENS auch nicht das Rissen Problem der Hacken an der Sache ist du must schon >SEHR LAUT< hören um auf die Spannung zu kommen das die LEDs überhaupt glimmen. Und im Video wird extra ein sehr bass lastiges Lied verwendet und das noch sehr laut damit die LEDs überhaupt flackern. Bei Zimmerlautstärke wird sich gar nix tuen oder kaum zusehen.
@@elektromicha6777 - Seriously? Do you even know what you are talking about? I did this with a car headlamp bulb when I was 13 on Dad's old Aiwa AF-5090. Lucky that it didn't fry the amp., should have added a resistor. However, it worked! Stuff your mouth with your old socks before you call it fake.
This is RGB(red ,green,blue)led strip 12V, so I can change colour by connecting different wires, but you can use one colour led strip that's more simple.
Braw.... this shit I was doing when I was 12-14 years old... now I am 24.... I thought that u found something better not like this. Something that will light up even you have the volume at 5% or at 50% and will illuminate with the same intensity based on the bass kicks, etc.
Unmm, I don't know about that one. The speakers run on AC voltage and LEDs work on DC so it would not work. But I think your led strips are AC voltage because you are not showing or writing it.
Yall, i only recommend if you take abart old bt speakers and use em for diy bs systems, I use leds with it straith connected, but if you have an expencive system that you def dont wanna replace, dont do it by anymeans, i actk as a short circut and will blow the sound chip real quick
What? You know this is a 3 way speaker yeah? So all 3 drivers would be affected not only the woofer (or sub as you call it even tho it's not). You are mostly just burning out the amp.
@@jomann3213 you can have a woofer with only medium and hight frequencies on it... what are you talking about? sub is a professional term to define lower frequencies under 60Hz that is even the frequency that electric current flows, besides, that kid also named the video about BASS , and no... not all frequencies are afected the same simply because the amp sends much more power from the crossover to deliver in the speacker the low and sub frequencies, than for the highs frequencies. If you use old lamps, you will see that they dont move much with the highs of music almost nothin but do a lot with kick drums and sub bass. for you to hear from a speaker tweter 15000Hz you need 300 times less energy from the amp, than the energy you need, to hear a Kick sub on theyre usual 50Hz frequencie.
Nice job , pretty sure the amp can deal with the extra 12v power draw , lol people in comments make me laugh it's not like he's going to have it on 24/7 with speakers at 100% lol it will be fine worst case scenario you have a power surge and pop an led , lol
LEDs require a 12v DC source. Your amplifier emits an alternating current or ac. This will effect how the load on the amp is received, and will cause damage to the components. Please stop telling people to do this.
Is there a way to do it
Can I connect it to every 7.1 channel? So I have separately visible from every sound channel
please dont inform people to do this as it will burn up the amplifier...
lol?
Yeah, TexasXplorer youre right
it did not burn the amplifier
@@paczkos545 not immediately but it will
Why? Pls show me i dont understand
This is very good to the amplifier 💥💥💥💥rest in peace
right
The title should be: How to blow up your amplifier
Yap :))
How....
@@mathwins7953 so if i have a 1973 Pioneer amplifier does it work?
Why?? Could you please explain me?
Exactly because I tried it and I blowed my amplifier too... Please don't try this
well im not very knowledge in eletronics but i know some, so there is a way to kill your amp by doing this, using AC (speaker works with Alternate Current, leds are designed to work with DC) with leds, youre forcing voltage into led in a way they are not meant to have, doing that any led in the strip may fail and go into short circuit and then kill your amplifier. Im thinking that theres is some workaround to this, adding some other diodes into the negatives and RGB inputs on the strip, or just using some resistors in the same way to limit the voltage that goes to the leds, dont ask me for schematics bcuz i dont know.
Hello Sir, how many led bulbs do i need for this particular project, thank you in advance.
1. Ruins your amp because of impedance
2. Only works with highs, unless you have a really powerful amp
hey, i just find your channel in my recommendation and we have almost the same "name", i tough it was funny ^^! nice content by the way
Hahaha that is funny, thanks!
th-cam.com/video/jABI0uKtpKE/w-d-xo.html
HEY EVERYONE DON'T TRY THIS CUZ IT CAN BLOW YOUR AMPLIFIER OR HOME THEATER JUST TAKE A 1K CAPACITOR AND CONNECT IT TO LED STRIP+ THEN CONNECT - WIRE TO LED STRIP AND ANOTHER WIRE (+) TO THE OTHER SIDE OF THE CAPACITOR THEN CONNECT IT TO YOUR SUB WOOFER OR SPEAKER 👍
He connected it to his stereo system
1: you make it look like more difficult
2: frome amplifier you get less power when it's normal volume, so you have turn volume a lot higher to get enough illumination
* putting led directly not gonna helps you
* just simply buy two amplifier one for speaker one for led
There can be other alternative but At least you don't have to turn higher volume and 100% sure that your amplifier don't blow ✌
How can I getbthese lights to buy?
Bhai kisi bhi hometheatre se kr sktee hai kyaa
3:59 music title please?
what is that 2 small metal what is it called?
It's led 12V bro?? Kindly reply
Eso no afecta el amplificado o puede dañarlo por la carga de tira led
para mi si
Do the colors change?
Can it be done with f n d 550x
Can you blow the LEDs with too much or would they not blow up??
They wont blow up but they will die
This is like the kind of thing that i would love to do but i just know that i will never bother learning because of the danger of fire lol. I wouldn't trust myself to not mess it up xd
I am 12 but....same 🤣
@@ConstabeastYT i am 13 and i do this things for 5 years now
@Teodor Vranchev i like mostly computers and speakers
@@CH-FOUR same
Nice, do you know if this works with more powerful amplifiers/speakers. Thinking of hooking them up to my 600w RMS subwoofer in my car
Bigger resistor, you only need a tiny amount of power from the signal and 600w will blow these up.
(I think) if you have an amp that does 600w @ 8Ω then it will do 300w @ 16Ω, 150w @ 32Ω, ...... 16w @ 128Ω, 8w @ 256Ω - measure the resistance of your strip and make up the difference in impedance with another resistor inline to bring it up to the correct value.
I would check the rating of your amp first, if it is actually 600w at 8Ω or 4Ω or whatever, from there you can extrapolate where you need to get to.
@@leeknivek it will work I’ve done it to amps that push out 1800 watts 🤙🏽
Nice work!👌👌👌
Remember the Radio Shack light organ boxes, where each of the 3 colors operated on the different sound levels? That's what I want to learn how to properly make.
Is the led light connected to the bass or is it separate? Is it safe to cut the led cord or will the bass be cut too?
Evet bass'a bağlı
Nice
I get inspired
Can we connect light direct speaker
Can I go directly to speaker?
DON'T TRY THIS
Bro I know it how to work set up I know operator I know
@@johnlloydcabacungan5717 Get a 1.1k resistor and connect directly to speaker
I Have Some Led Strips with 4 Pin Connectors
How Do I Know What Wires Are + Or -
I don't recommend it at all, but black is usually negative, use a battery to be sure
You kill the amplifier!!!
Ja Moin, dich sieht ja man überall😂
@@marcel7036 Ja normal. Sowas wie hier geht auch nicht. XD
@@Speakershocker ja geht auch nicht, teure Verstärker schalten da schon automatisch ab
@@marcel7036 bei so einem Unfug aber auch nicht immer.
@@Speakershocker kannst du mir erklären warum hier der Verstärker kaputt geht? Kenne mich jetzt nicht wirklich aus aber wer nicht fragt bleibt dumm...
Wenn jetzt theoretisch die Gesamtimpedanz über der Minimalimpedanz des Verstärkers liegt (z.B nur die LEDs ohne Boxen) fährt der Verstärker doch auch nicht ins Clipping. Dem is dass doch egal oder? Oder weil der Strom jeweils immer nur ne halbe Periodendauer fließt weil die LEDs während der negativen Amplitude sperren?
Was schädigt hier dem Verstärker?
Danke
This is so cool !!! Amazing :D
Awesome good bro 😍
Hi Hifi, it was the same and the ohm is adjusted to the speaker, performance when recording and transmitting, it's no use putting up a series of LEDs equipped with resistors, an LED works at about 3v, so you not only damage the hifi, but it can also cause a short circuit because there is no switch on it!
Where did you insert the 2 pins
This kills the amplifier
How?
@@gameboy1984 Drains too much current from it to light up leds
@@davidluptak go on
@@Kanoshe Amplifier is for speakers with definitive ohms and if you add another appliance like leds than mosfets or chip may burn up from excess current
@@davidluptak 4 ohm speaker is a much bigger load than those few LEDs
Loved this video because no difficult tasks is there...
Nice Video
led price ??
Oh Junge 🤦♂️ macht das bitte nicht nach, das zieht eurem Verstärker nur Leistung und senkt den Widerstand des Lautsprechers am verstärker was ihn zerstören kann.
Das Stimmt Nur bedingt! Dem Verstärker ist das erstmal egal die LEDs mit widerstand haben einen VIEL höheren widerstand (je nach länge) als das sie schaden anrichten könnten.
ABER Ein Problem ist eher das der Verstärker ungleich belastet wird.
LED Lassen Strom nur in eine Richtung Durch Das heist die belasten auch nur bei einen positiven Impuls NICHT aber bei dem negativen.
Dafür wäre eine Gleichrichtung mit elko nötig)
Das ist aber MEISTENS auch nicht das Rissen Problem der Hacken an der Sache ist du must schon >SEHR LAUT< hören um auf die Spannung zu kommen das die LEDs überhaupt glimmen. Und im Video wird extra ein sehr bass lastiges Lied verwendet und das noch sehr laut damit die LEDs überhaupt flackern. Bei Zimmerlautstärke wird sich gar nix tuen oder kaum zusehen.
Ich hab's mir schon gedacht das es nicht so einfach sein kann
awesome
You know that you actually can cut the shrink tubes shorter depending on how much you need?
I knew it but I don’t do it.
Cut is cut
@@paulybeatz3688 I know man but honestly it drives me crazy when I see someone wasting material like that..
Yes all cool and that but if u have a radio that outputs more than led's are rated for they are going to frie.
How many led lights can it make glow? Because when i connected a series, it didn't glow. Can you help me with some calculations
bro this is fake ;/
@@elektromicha6777 - Seriously? Do you even know what you are talking about? I did this with a car headlamp bulb when I was 13 on Dad's old Aiwa AF-5090. Lucky that it didn't fry the amp., should have added a resistor. However, it worked! Stuff your mouth with your old socks before you call it fake.
10 m led strip have about 24watts so his thing will have 3 watts. so shouldn't impact the performance a lot.
Is that a normal 12 volt led strip?
This is RGB(red ,green,blue)led strip 12V, so I can change colour by connecting different wires, but you can use one colour led strip that's more simple.
@@AVmake but what if the sub is in the amp and only tweaters are out of it ...
hi brother what is the positive lead the green? .... the green goes connected with the red of the amplifier?
I've never seen so many "no-no's" in a how to video. I won't even go into it. Everyone has to learn somewhere. lol.
Is not working 😥 plz help
Braw.... this shit I was doing when I was 12-14 years old... now I am 24.... I thought that u found something better not like this. Something that will light up even you have the volume at 5% or at 50% and will illuminate with the same intensity based on the bass kicks, etc.
How?
yeah apparetnly you gotta have like arduino's and coding to make it proper
@@Kanoshe you can use a spectrum analyzer board
Somebody got his big boy pants on all by himself 😂
Yo I've been searching for shit like that. Every tutorial or led light kit seems so basic.
It will burn your amplifier and btw there is Sony speakers with pre installed LED
Can I do this with my Creative A120 ???
Bro how I set in microlab speakers
Unmm, I don't know about that one. The speakers run on AC voltage and LEDs work on DC so it would not work. But I think your led strips are AC voltage because you are not showing or writing it.
Buy Yeelight Strip light this feature is also available in that strip
Please give links
Bro, I need some guidance with a project that I am doing, can we get in touch?
Ap na ky use kiya ha bata sktaho
Yall, i only recommend if you take abart old bt speakers and use em for diy bs systems, I use leds with it straith connected, but if you have an expencive system that you def dont wanna replace, dont do it by anymeans, i actk as a short circut and will blow the sound chip real quick
Excellent Work ..
Bhai is led strip ma length ka bhe hesab hota ha ya nai
Replay plz
How meny LED can you have of the speakers
Where to put the wires in the input or output socket???????
Why is it only blue not red and green
One tip you meed to use a 5v (volt) led strip with a collor blu Red or green use to much voltage I hope this wil help you with making these things👍
I'm not sure if I want to do that to my speakers
congratulations, you work is very beautiful.
parabens, seu trabalhor ficou muito bonito.
How come you can't just use red and black and directly hook into pos and neg on speaker
0:05 SONG NAME?
It was perfect, congratulations
By doing so you are reducing the power inputed to the sub
What? You know this is a 3 way speaker yeah? So all 3 drivers would be affected not only the woofer (or sub as you call it even tho it's not). You are mostly just burning out the amp.
@@jomann3213 you can have a woofer with only medium and hight frequencies on it... what are you talking about? sub is a professional term to define lower frequencies under 60Hz that is even the frequency that electric current flows, besides, that kid also named the video about BASS , and no... not all frequencies are afected the same simply because the amp sends much more power from the crossover to deliver in the speacker the low and sub frequencies, than for the highs frequencies. If you use old lamps, you will see that they dont move much with the highs of music almost nothin but do a lot with kick drums and sub bass. for you to hear from a speaker tweter 15000Hz you need 300 times less energy from the amp, than the energy you need, to hear a Kick sub on theyre usual 50Hz frequencie.
How much wattage the led strip light should be?
I have made a 200w speaker I power it up with 12v 5amp adaptor
I have tried it when I power the speaker it just bumps up and not blink after the music is on
Please let me know about it
Song?
Can we use 20 watt led strip tube light on strip (T5 100 led)without driver please reply anyone ASAP
Can you add led lights to JBL boombox 3
Thank you so much ❤️
Use a transistor to switch the led strip and connect the base pin of the transistor to the amp like you did not...
Vai led strip kitna volt ke hai
th-cam.com/video/jABI0uKtpKE/w-d-xo.html
Pakai adaptor gk bang
song at 4:03
Thank you
Actually u can just go buy rgb led strips with mucis mode
Cost bro 🤧
Is amplifier ka Kya naam Haii Plzz link dija.....plzzz plzzzzz
all genius things are very easy
Bikin video bos pasang lampu led semua jenis , dri lampu kolong lampu led strip dll pasang ya ke batok lampu sorot viar 200L dan motor matic
Nice job , pretty sure the amp can deal with the extra 12v power draw , lol people in comments make me laugh it's not like he's going to have it on 24/7 with speakers at 100% lol it will be fine worst case scenario you have a power surge and pop an led , lol
Thanx bro
i also made this one but the amplifier never blew up.
Hitlights Told Me The Led Strips Won't Work
Just Connected To Speakers.
They Said They Need A Content Steady
Flow Of 12 Volts.
4:09 sound tittel?
Have you found it?
@@alexandrualex2066 no
If you do let me know
a little late but darude sandstorm
Buwat apil besar bisa a om
Hola buen dia yo tengo esa luz led pero el mio tiene dos cables se hace lo mismo ?
Si le das más volumen no se queman decasulidad
Why RGB? U can use blue led tape????
Ovo sam imao,pa eto da iskoristim...
@@AVmake haha ja ne mogu da verujem, zaista nisam očekivao da srpski pričaš
Jako prijatno si me iznenadio. Ps jako mi se sviđa ovo što si napravio
:-)
@@AVmake Sviđa mi se tvoj kanal! Evo subscribe :)
Pozdrav!Zapravo sam iz Hrvatske,vidio sam ti ime pa mi je lakse bilo odgovorit na hr hahah
How to blow up the led strings
Holaa yo lo hago asi como muestra el video lo ise y no prende las luces xq seria q no prende
So cool
its not working
plz help
Wheres the problem
Ham Yaha light parichit karna chahte hain kahan milega
Song at 3:57 pls
Jensation - delicious look it up on youtube and its the one by ncs.
Nice
Name song 3:20?
Warriyo - mortals
3:15 wats the songs name? Plzz
Mortals warriyo feat Laura brehm