gracias por este video que aporta bastante para quienes se inician en mantencion de bombas. Este tipo de videos ayudan a la formacion de buenos tecnicos. por favor sigan publicando
uggestions:1st, avoid contamination of lubrication on d seal faces by applying d fluid in d pump bore & shaft rather than on d seal itself. 2nd, use an installation tool instead of screw driver. A slip of d screw driver can damage d rubber, & d likelihood of d drive band being installed too deep into d seal face side;which virtually nullifies d ability for d seal face side to float axially. Lastly, arbor press should be used to install d stationary seat in order to avoid parallelism issues.
First of all you have loctited a seal sleeve to a stainless steel shaft, which would require a activation spray as stainless steel isn't a reactive material,, so seal sleeve may possibly slip in the future, causing a leakage path between sleeve / shaft . The use of a soap detergent isn't recommended for the stationary seal seat or the rotational seal. And never fit a seal without a suitable seal bush to eliminate any rubber boot damage
Mucha limpieza en el lugar de trabajo nada de suciedad un ejemplo para los tecnicos mexicanos que suben sus tutoriales y todo bien puerco aunque lo expliquen bien.
Not even checking seal working length, and how is that impeller nut going to hold tight, again stainless bolt and shaft no activate spray used, No proper torque setting , 30NM minimum and not even torqued onto shaft taper properly. No way to fit a gasket without a set of alignment studs . Need to improve your assembly skills mate !
gracias por este video que aporta bastante para quienes se inician en mantencion de bombas. Este tipo de videos ayudan a la formacion de buenos tecnicos.
por favor sigan publicando
luis Diocares
liked
Que tipo de aceite es ese el que ocupa para lubricar los cellos
밀봉 물이 모터 안 들어 오게 검은것 넣고 흰것 아니고
흰것 넣고 검은것 넣 어떤 문제 입니까
메카리씰 축 및 케이스 들어감 안 십히게 구리스 바름
uggestions:1st, avoid contamination of lubrication on d seal faces by applying d fluid in d pump bore & shaft rather than on d seal itself. 2nd, use an installation tool instead of screw driver. A slip of d screw driver can damage d rubber, & d likelihood of d drive band being installed too deep into d seal face side;which virtually nullifies d ability for d seal face side to float axially. Lastly, arbor press should be used to install d stationary seat in order to avoid parallelism issues.
잘보고 갑니다 도움이 되었네요 수고 하셨습니다 south korea man
what was the first liquid he used on the brass sleeve?
홈 안 메카 흰것 넣고 검은것 넣어면 안 됩니까
넣음 윤활 바름 십핌 방지
First of all you have loctited a seal sleeve to a stainless steel shaft, which would require a activation spray as stainless steel isn't a reactive material,, so seal sleeve may possibly slip in the future, causing a leakage path between sleeve / shaft .
The use of a soap detergent isn't recommended for the stationary seal seat or the rotational seal.
And never fit a seal without a suitable seal bush to eliminate any rubber boot damage
What you recommend instead of soap for installing the seal and why??
@@zhr4121 Silocain grease, washing up liquid is considered corrosive to delicate parts like seals and rubbers.
If you ever make another video. Do it without sound
It's vertical pump???
vamos sempre divulgar os vídeos e conhecimentos que temos de melhor em qualquer lugar a união faz a multiplicação tamos juntos.
André Araújo visita o meu canal🤙🏼
Thank you so much, nice demostration.
Muchas gracias, ya tengo más claro como colocar un Sello Mecánico!
what liquid you apply on the stationary ??
Flo meter?
Mucha limpieza en el lugar de trabajo nada de suciedad un ejemplo para los tecnicos mexicanos que suben sus tutoriales y todo bien puerco aunque lo expliquen bien.
Barulho de mais
Very good assemble of mechanical
good video, very useful !
Good luck 🤝
Great work thanks
very nice video
Not the ideal way to insert the mechanical seal. But, yeah, screw driver may work.
Washing up liquid to the 'O Ring' surface prior to pressing same into the stationary housing and a squeeze of soapy water on the shaft to
thank you
good job bro
Looks like water circulator, maybe.
Pepa
Not even checking seal working length, and how is that impeller nut going to hold tight, again stainless bolt and shaft no activate spray used,
No proper torque setting , 30NM minimum and not even torqued onto shaft taper properly.
No way to fit a gasket without a set of alignment studs .
Need to improve your assembly skills mate !
wouldn't let this guy service my pump
Malo Hoang dxxxx
تسلم ايدك
please, never install mechanical seal that way. Never!
How should it be??
@@zhr4121 The Seal Guru has the answer below
method id good
useful think
Hi my friend, I am mechancial seals manufacturer. If any interested, please let me know.
.
wrtrr