@pedekiller Yeah my heat gun goes from 0C (32F) to 80C (176F) in about 8 seconds. Mill only needs to be 160F ish for pre=heat. That way there is less strain on the piston, and it will fire in 1 pull. and if your LSN is set from a previous run all you have to tune is the HSN. and have you heard of WD40?? Spray it on the block and the tvp's and the oil from the nitro will run right off. Spray it on the bottom of the chassis and the mud will run right off.
I was wondering, if you have your batteries hooked up to the car, does it waste the battery's juice if you turn on the evx 2 leaving it at throttle, since you have to put on the body and clips?
@pedekiller WRONG ! It takes next to no skill to tune a mill . Ill have my mill pre-heat, tuned up and ready to go before your done hooking one batt up =P
somebody, please tell me what's the name of that chasis cause i love it, and i am doing my brushless conversion on my revo 3.3... i really like that one! thx!
Its a race truck. Not a top speed truck. Top speed seen on most tracks don't exceed 40MPH tops. Track racing is more about driving skill than top speed.
![🔴 ฟุตบอลแชมป์กีฬา 7HD แชมเปียน คัพ 2024 [รอบรองชนะเลิศ]](http://i.ytimg.com/vi/zPm8ClLVhoE/mqdefault.jpg)
![[Part 1] ทารกน้อยถูกทิ้ง👶 หญิงชราเก็บขวดขายเลี้ยงดูเขาจนโต #โลกการละคร](http://i.ytimg.com/vi/nPTDvFCExks/mqdefault.jpg)
Let's see it run!!!
@pedekiller
Yeah my heat gun goes from 0C (32F) to 80C (176F) in about 8 seconds.
Mill only needs to be 160F ish for pre=heat. That way there is less strain on the piston, and it will fire in 1 pull. and if your LSN is set from a previous run all you have to tune is the HSN.
and have you heard of WD40??
Spray it on the block and the tvp's and the oil from the nitro will run right off. Spray it on the bottom of the chassis and the mud will run right off.
Good job!
I was wondering, if you have your batteries hooked up to the car, does it waste the battery's juice if you turn on the evx 2 leaving it at throttle, since you have to put on the body and clips?
Yes mate it will fit a E Revo
Those are Pro-Line Bow-Tie MTR and Crime Fighter MTR tires in the 1/2" offset
Theres no clutch. Its an adapter for electric motors so they can use the larger pinions needed for nitro trucks.
Hey how does the 2 speed work with the brushless.
@pedekiller
WRONG !
It takes next to no skill to tune a mill .
Ill have my mill pre-heat, tuned up and ready to go before your done hooking one batt up =P
@SCRTpilot You could say it's both.
What Magazine for the whole article
youre calling him a noob? I bet that revo would rock every car that you own offroad
the e revo brushless edition with 11.1 3S lipo X2 would destroy that bodge job!
what tires and wheels and sizes do you have?
somebody, please tell me what's the name of that chasis cause i love it, and i am doing my brushless conversion on my revo 3.3... i really like that one! thx!
Will that body fit a erevo?
@joeowen50 there are lots of steel driveshafts at rc4wd.com and you should check there to see if anything works
how about a brushless losi 8T
@goastdoggg and handling
doesnt erevo have twim motor?
why does ithis have one
A real race kit is from Bomb-Proof Products and Mr. C conversions.
I see u tured a revo in to a erevo
lmao same here.
Its a race truck. Not a top speed truck. Top speed seen on most tracks don't exceed 40MPH tops. Track racing is more about driving skill than top speed.
That sounds like it cost u 2+k to build
huh?
ummm...soo...brakes?