Mk3 Supra transmission removal and clutch installation

แชร์
ฝัง
  • เผยแพร่เมื่อ 24 ธ.ค. 2024

ความคิดเห็น • 20

  • @hammysandmich5252
    @hammysandmich5252 5 ปีที่แล้ว +3

    Your channel will get big if you keep this up nice video

    • @suprachefgarage9845
      @suprachefgarage9845  5 ปีที่แล้ว +1

      Thank you! Your positive feedback is always appreciated here. Btw I will be on the dyno in the next month hopefully.

  • @sunnyblumen3807
    @sunnyblumen3807 3 ปีที่แล้ว +2

    What does it mean when you say fill up to this drain plug? Do I fill with max fluid level in tsrm then loosen plug to ensure oil has reached it and let out air? Want to make sure I understand

    • @suprachefgarage9845
      @suprachefgarage9845  3 ปีที่แล้ว

      I take that plug out and fill the transmission until gear oil comes out of the plug on the side of the transmission. Make sure the car is level and keep a catch pan under the transmission fluid. I can send you pics or a short video from my instagram later if you would like @suprachef

  • @oudomkosaketh40
    @oudomkosaketh40 4 ปีที่แล้ว +1

    Im literally stuck here on my supra. Ive only seen like a minute so far. Is this a 7m gte or 1jz gte? Or something else?
    Aside from that. Cant figure out how to put it back in. The transmission.

    • @suprachefgarage9845
      @suprachefgarage9845  4 ปีที่แล้ว

      2jzgte in a MK3 Supra with the R154 transmission. Reinstalling the transmission is a bit of a pain. What do you have?

    • @oudomkosaketh40
      @oudomkosaketh40 4 ปีที่แล้ว

      I have a 7mgte with r154 transmission. Trying to figure out how to put the trans back in. Just not enough space. Thought of jacking the front of the engine to give a better angle.
      But i also didnt know you had to put the trand in first, then tighten the clutch. I think.

  • @671carkulture2
    @671carkulture2 3 ปีที่แล้ว +1

    Ayye bro, I really need help, so my tranny is in but now I am trying to figure out where the wires go and I don’t know how

    • @suprachefgarage9845
      @suprachefgarage9845  3 ปีที่แล้ว

      I believe there is only the reverse switch. The wires run down the drivers side on my car

  • @dan.dom.2445
    @dan.dom.2445 10 หลายเดือนก่อน

    How much clearance did you need off the floor?

    • @suprachefgarage9845
      @suprachefgarage9845  10 หลายเดือนก่อน

      Approximately 20" from then punch weld to the floor. My floor sags a little right there. I believe I kinda pushed the transmission off the jack to get it out from under the car though.

  • @erickportillo613
    @erickportillo613 2 ปีที่แล้ว

    Hey how many bolts are connected to the motor

  • @UncontrollableOne
    @UncontrollableOne 4 ปีที่แล้ว +1

    Thank you for this bro!!!!!

  • @andyalexisvasquez4082
    @andyalexisvasquez4082 4 ปีที่แล้ว +1

    Youre the man !!

  • @majorva2653
    @majorva2653 3 ปีที่แล้ว

    this is a 3 inch stainless---- completely rusted xD

    • @suprachefgarage9845
      @suprachefgarage9845  3 ปีที่แล้ว

      The downpipe is a poor quality steel. The rest of the exhaust pipe is better stainless