I know this is old but for anyone wanting to do this don’t replace the battery light with LED is is part of the charging system and it needs resistance of incandescent bulb to work properly.
At 1:47, why do they send the bulbs like that with the wire bent over both sides? Do they work like that in some instrument clusters with the wire bent over both sides?
At 6:35 I assume since you had modified the bulb where it only had wire on one side at least when you put in before 6:35 on the left side and it was not working. At least all you had to do was turn it (flip it in the socket) to get it to work and when it was in there wrong way it did not damage the circuit board, correct???
Thanks for the suggestion on the oil pressure line. I would like to find a way to replace the oil pressure gauge with an electric sending unit but have not found a way to do that yet. I have a 1981 Mercedes 240d and I haven't found a project yet that is recorded on TH-cam that shows anyone who has successfully done this project.
@@dieselbenzrevive6820 Exactly, i tried it and it was a really easy fix, i just heated the copper coil/tube and rubbed tin where the leak was, it fixed the problem right away! Took about two hours from start to finish. :-)
You prolly dont care but if you guys are stoned like me during the covid times you can stream all the latest movies on instaflixxer. Been binge watching with my gf for the last couple of days xD
Make sure to tighten the oil pressure line so it does not come loose. I had a bad experience and what a mess. I finally got it cleaned up but I had to clean a lot of oil.
I fabricated my own from small LED but the color of the light is not as pleasant as the vintage bulbs even warm white LED is not so great but less heat.
Your referring to the all glass tiny bulbs that illuminate the center console switches. Do you remember the old school Led that where plastic those are a good solution.i can make a short video of you like
@@dieselbenzrevive6820 Yep - those are the tiny bulbs I'm referring to. I was hoping to make an all LED swap while I have my dash out so I don't have to worry about replacements again but couldn't figure out the equivalent LED option. I'd love to see that video - thanks!
i soldered a resistor instead of a wire where the potentiometer is supposed to be, i just want the lights to be really low dimmed so that i dont get blinded by the cluster lights. Works fine!
Wish I had saw your video before messing up my cluster. Thinking you install the bubs like they came.
How’d you mess it up?
I know this is old but for anyone wanting to do this don’t replace the battery light with LED is is part of the charging system and it needs resistance of incandescent bulb to work properly.
At 1:47, why do they send the bulbs like that with the wire bent over both sides? Do they work like that in some instrument clusters with the wire bent over both sides?
At 6:35 I assume since you had modified the bulb where it only had wire on one side at least when you put in before 6:35 on the left side and it was not working. At least all you had to do was turn it (flip it in the socket) to get it to work and when it was in there wrong way it did not damage the circuit board, correct???
Excellent job! Very helpful. Thanks.
UPDATE: DO NOT USE HOT GLUE. Use epoxy on the led bulbs 1:19
Yes the hot glue melts and then the bulb gets stuck. Use EPOXY.
What king of epoxy
Update : the oil line is a 13mm and 10mm not 14
also i dont like the color of the white LED lights the factory bulbs look better in my view.
They make a warm version of these LEDs, I'm curious to see if that looks good.
i just ordered some and im going to test out the warm white
What a Great video! Maybe one day you will come back and give some likes! hehe lol
Thanks for the suggestion on the oil pressure line. I would like to find a way to replace the oil pressure gauge with an electric sending unit but have not found a way to do that yet. I have a 1981 Mercedes 240d and I haven't found a project yet that is recorded on TH-cam that shows anyone who has successfully done this project.
its easier to just fix the original part or get a good used one
@@dieselbenzrevive6820 can i use tin to "solder" the oil pressure gaguge thingy where it leaks? Or what is the prefered method?
@@philen are you refering to the oil pressure guage from leaking oil inside the car? i used solder generaly used in copper water pipes.
@@dieselbenzrevive6820 Exactly, i tried it and it was a really easy fix, i just heated the copper coil/tube and rubbed tin where the leak was, it fixed the problem right away! Took about two hours from start to finish. :-)
You prolly dont care but if you guys are stoned like me during the covid times you can stream all the latest movies on instaflixxer. Been binge watching with my gf for the last couple of days xD
Hey bro I’m curious is there a way to check the back dashboard lights before putting it back together?
4:09 what size and material wire did you solder??
Make sure to tighten the oil pressure line so it does not come loose. I had a bad experience and what a mess. I finally got it cleaned up but I had to clean a lot of oil.
yeah happened to me once too what a mess.
Ruined many a pair of shoes before i figured that one out.
Dude! Thanks for the tip.
Did you happen to source LED replacements for the tiny bulbs that light up the switches in the center of the dash?
I fabricated my own from small LED but the color of the light is not as pleasant as the vintage bulbs even warm white LED is not so great but less heat.
Your referring to the all glass tiny bulbs that illuminate the center console switches. Do you remember the old school Led that where plastic those are a good solution.i can make a short video of you like
@@dieselbenzrevive6820 Yep - those are the tiny bulbs I'm referring to. I was hoping to make an all LED swap while I have my dash out so I don't have to worry about replacements again but couldn't figure out the equivalent LED option. I'd love to see that video - thanks!
@@plymsat71 rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F123897764301
@@pinzgauernorcal thanks for the help!
Still can't figure out how one uses SOLDER wire, a SOLDERING iron and then SODDER the connections. Then again in South Africa we speak ENGLISH.
i soldered a resistor instead of a wire where the potentiometer is supposed to be, i just want the lights to be really low dimmed so that i dont get blinded by the cluster lights. Works fine!