How to make wireless water level indicator without any microcontroller

แชร์
ฝัง
  • เผยแพร่เมื่อ 23 ก.ค. 2018
  • JLCPCB Prototype for $2(Any Color): jlcpcb.com
    Hello everyone,
    In this video I will show you , how you can make a wireless water level indicator with water pump controller ....
    Components required...(affiliate link present)
    Transmitter
    1. 433 mhz transmitter.......goo.gl/xyooYd
    2. HT12E IC.......amzn.to/2A48Fg2
    3. 18 PIN IC BASE (OPTIONAL)
    4. 1 MEGAOHMS RESISTOR
    5. 10K RESISTOR*4
    6. 9V OR 5V BATTERY OR POWER SUPPLY(USE 2*3.7V BATTERY IN SERIES CONNECTION)
    7. BC 547 TRANSISTOR*4
    8. SMALL PCB.......amzn.to/2uKNjiX
    9.220 OHMS RESISTOR 4
    RECEIVER
    1. RF RECEIVER......goo.gl/xyooYd
    2. HT12D IC.........amzn.to/2A48Fg2
    3. 18 PIN IC BASE (OPTIONAL)
    4. 9V OR 12V POWER SUPPLY
    5. 51K RESISTOR
    6. 5K RESISTOR*4
    7. 5 LEDS
    8. SMALL PCB......amzn.to/2uKNjiX
    IF YOU WANT TO USE PUMP THEN ADD
    1. 12V 20AMPS RELAY
    2. 1 BC 547 TRANSISTOR
    TIPS......
    1.USE JLC PCB WEBSITE FOR THIS PROJECT......
    2.USE A LONGER WIRE FOR ANTENA FOR BETTER RANGE
    3. USE 9V SUPPLY AT TRANSMITTER & 12V AT RECEIVER
    CIRCUIT DIAGRAM
    RECEIVER-drive.google.com/file/d/1uIk8...
    TRANSMITTER
    drive.google.com/file/d/1ttlJ...
    THANKS FOR WATCHING....
  • แนวปฏิบัติและการใช้ชีวิต

ความคิดเห็น • 72

  • @kumar7tube
    @kumar7tube 5 ปีที่แล้ว +1

    How much this setup will cost and what is the distance it covers. Can I purchase from you.

  • @bapisaha3990
    @bapisaha3990 ปีที่แล้ว

    circuit diagram for recever and transmitter is not available, from your link given here. Please give the circuit diagram link again.

  • @prasadksr6459
    @prasadksr6459 4 ปีที่แล้ว +2

    I have 3 queries. 1. Will this interfere with other wireless devices? 2. What is the total cost? 3. Antenna is a simple wire or something else? Please answer.

  • @dugu11
    @dugu11 2 ปีที่แล้ว

    I make it but transmitter battery running only 4 days, please suggest for long run of transmitter battery

  • @ramuvanparti
    @ramuvanparti 4 ปีที่แล้ว +5

    Can you please make the video of actual circuit making and assembling of all component

  • @omparkashkararwal6509
    @omparkashkararwal6509 4 ปีที่แล้ว

    Sir 9 volt battry ketna time used

  • @SS_Gaming
    @SS_Gaming 3 ปีที่แล้ว

    Why we used transistor there (to control the motor)

  • @maxaladin8924
    @maxaladin8924 4 ปีที่แล้ว

    Can you make a long range wifi batery indicator with the same circuit ???

  • @parvezsheikh2513
    @parvezsheikh2513 2 ปีที่แล้ว

    How meny distance covered??

  • @bselectrician1530
    @bselectrician1530 ปีที่แล้ว

    Sir, the circuit is 9v, but the relay is 12v, please reply, thanks,

  • @SubodhKumar-di8jc
    @SubodhKumar-di8jc 9 หลายเดือนก่อน

    Range?

  • @shammi59
    @shammi59 2 ปีที่แล้ว

    From where can we get this

  • @aakashnagar5118
    @aakashnagar5118 10 หลายเดือนก่อน

    Hello
    The attached files are missing

  • @RajkumarRaj-qs6oi
    @RajkumarRaj-qs6oi 5 ปีที่แล้ว +1

    Badlapur all hot work thank you information full Technology thank you

  • @rahulgkhs
    @rahulgkhs 4 ปีที่แล้ว

    There are lots of grounded pins in the encoder-decoder, can those be utilised to increase the resolution?

    • @SOUNDFOLIO369
      @SOUNDFOLIO369 2 ปีที่แล้ว +1

      That gnded pins are for addressing
      Which are the pins connected in encoder that should maintain in decoder otherwise it's not work properly

  • @lingeswaranr1617
    @lingeswaranr1617 4 ปีที่แล้ว

    Thanks u r guide

  • @VikasSharma-lc7ge
    @VikasSharma-lc7ge 5 ปีที่แล้ว

    सर मोटर ओटो मेटिक ओन ओफ होने के लिये हम कया लगाये जो ऐसा हो जाये

  • @AMOL8143
    @AMOL8143 4 ปีที่แล้ว

    Sir can we add motor in this , auto on off , which water tank empty

  • @monadicyt521
    @monadicyt521 4 ปีที่แล้ว

    I need a help sir,
    If this device install in water tank which at roof and receiver place in the room then work properly??

    • @devendrasagar1342
      @devendrasagar1342 3 ปีที่แล้ว

      Transmitter placed on tank and reciever placed incide home

  • @njrchannel2249
    @njrchannel2249 5 ปีที่แล้ว

    Very nice

  • @anitha_kiran
    @anitha_kiran 5 ปีที่แล้ว +6

    Sir , what is the range covered by the transmitter?

    • @jamtechguru5580
      @jamtechguru5580 4 ปีที่แล้ว

      100 meter

    • @SOUNDFOLIO369
      @SOUNDFOLIO369 2 ปีที่แล้ว

      30 mtrs

    • @ekamautomation1567
      @ekamautomation1567 ปีที่แล้ว

      @@jamtechguru5580 this circuit range is only 5 to 10 meter

    • @nabilseoudi2910
      @nabilseoudi2910 ปีที่แล้ว

      Is it 100 meters or 5 meters ? It looks like no one have the correct answer!

  • @jaishree5431
    @jaishree5431 5 ปีที่แล้ว +1

    Sir
    Underground water tank me pani nahi hone par bhi Water leval indicator me sari lights on Rahati hai. Explain me sir

    • @HowToBro
      @HowToBro  5 ปีที่แล้ว

      That means all the trigger wires are connected to the supply.... that's why the leds are always on....

  • @adamsaifur5639
    @adamsaifur5639 3 ปีที่แล้ว

    Hosem video bro

  • @RizwanAli-ev9gm
    @RizwanAli-ev9gm 3 ปีที่แล้ว

    Pani m wire par corozen lag jaata hai.ye success ni hai.m pehle bhi try kar chuka hu.kuch esa ho jo wire tank m n dalna pade.

  • @patelkush5353
    @patelkush5353 5 ปีที่แล้ว

    Jlcpcb ke undar jo file apne upload ki thi vo kaha milegi

    • @HowToBro
      @HowToBro  5 ปีที่แล้ว

      Check description

  • @palashjyotibhuyangau-c-1719
    @palashjyotibhuyangau-c-1719 3 ปีที่แล้ว

    great

  • @CKCREATION02
    @CKCREATION02 4 ปีที่แล้ว

    Bro this transistor is npn or pnp
    Emmiter connected to 9v

    • @CKCREATION02
      @CKCREATION02 4 ปีที่แล้ว

      In npn Emmiter is ground hey na

    • @HowToBro
      @HowToBro  4 ปีที่แล้ว

      @@CKCREATION02 npn

    • @abhrajitchanda2447
      @abhrajitchanda2447 4 ปีที่แล้ว

      @@HowToBro apne to npn transistor ka emitter kor 9v diye hai circuit diagram pe oi hai but emitter to gnd hoga na!!!!!!

    • @trevor18ut
      @trevor18ut 4 ปีที่แล้ว

      @@abhrajitchanda2447 Hi, You are right the circuit Emitter goes to +ve whereas npn normally is -ve. Comment and correct me if wrong.

  • @EforEngineering
    @EforEngineering 5 ปีที่แล้ว

    Can i get pcb from jlcpcb in West Bengal?

    • @HowToBro
      @HowToBro  5 ปีที่แล้ว

      FUN WITH ELECTRONICS yes...

    • @EforEngineering
      @EforEngineering 5 ปีที่แล้ว

      Any delivery charges?

    • @HowToBro
      @HowToBro  5 ปีที่แล้ว

      Depends on many factors....you can contact to the support team...

  • @VijayVijay-en2lj
    @VijayVijay-en2lj 3 ปีที่แล้ว

    Make a new video with 12v or 24v relay connection with rf receiver
    Make sure you clearly explain wire connection with relay
    I hope you make this tutorial as soon as possible but speak in HINDI

  • @BluCasper
    @BluCasper 2 ปีที่แล้ว

    you should recheck your design. something is wrong.

  • @joshitoshi9835
    @joshitoshi9835 3 ปีที่แล้ว

    Thanks for enlightening us but this is not a practically working circuit design i guess, because if we attach it with motor and when upper level is achieved motor will be off and when some water is used than motor will be turn on again and therefore motor will remain on always which is not feasible. You didn't tell this in the video, So please make another video addressing this issue and there should be manual switch to turn on.off motor at any time. Any micro-controller or nodemcu can be used to do that i guess.
    Also it will be very helpful for students and tech guys if you educate us how this thing will work, why we are using transistors and how water level will be achieved by ics so that we can apply this knowledge to other projects too instead of copy pasting circuit designs.

  • @surinderdhiman
    @surinderdhiman 4 ปีที่แล้ว +1

    Best video in its class

  • @rafiqueuddin7215
    @rafiqueuddin7215 5 ปีที่แล้ว

    Range kitni h Mr.

    • @HowToBro
      @HowToBro  5 ปีที่แล้ว

      upto 50 meters...

  • @techieelectro3355
    @techieelectro3355 5 ปีที่แล้ว

    But every time jab pani use karne ke baad 4th level se niche jayega to motor automatically on ho jayegi.. to motor hamesha on off on off hoti rahegi .... Is this right na?
    Reply????

    • @HowToBro
      @HowToBro  5 ปีที่แล้ว +1

      yes I agree ...& I also thinking about this problem without any microcontroller...hope I will upload that video very soon...

    • @rahulkamboj9375
      @rahulkamboj9375 5 ปีที่แล้ว

      Bhi tu apna b mind use kr,,, extra sensor use kro

    • @abhrajitchanda2447
      @abhrajitchanda2447 4 ปีที่แล้ว

      Iske liye apko 555 timer ic ka use karna parega to ap ak level select kar sakthe ho ki ap ak level set karo ge us level pei pump on hoga

    • @shammi59
      @shammi59 2 ปีที่แล้ว

      Transmitter & receiver. How to link them or say pair them

  • @nageshgatty9510
    @nageshgatty9510 4 ปีที่แล้ว

    Sir,
    I want design this model , where i get the Rx & Tx module and what the range of Tx , will it cover about 500mtrs
    can you give me your Phone no: PLz.

  • @Aradhya_Agrima
    @Aradhya_Agrima 4 ปีที่แล้ว

    1m resister kitne watt ka h
    10k resistance kitne watt ka h
    51k resistance kitne watt ka h
    5k resistance kitne watt ka h

    • @HowToBro
      @HowToBro  4 ปีที่แล้ว

      Everythin . 25 watt

    • @Aradhya_Agrima
      @Aradhya_Agrima 4 ปีที่แล้ว

      @@HowToBro thanks

  • @trevor18ut
    @trevor18ut 4 ปีที่แล้ว

    Has anyone tried this circuit, please comment on its fuction.

  • @maheshpagremaheshpagare8684
    @maheshpagremaheshpagare8684 4 ปีที่แล้ว

    हिन्दी में बता भाई

  • @trevor18ut
    @trevor18ut 4 ปีที่แล้ว

    Need your support, please email.......

  • @balwinderjaat305
    @balwinderjaat305 5 ปีที่แล้ว

    Sir mujhe quantity me chahiye h 8950851001

    • @HowToBro
      @HowToBro  5 ปีที่แล้ว

      Order it from jlcpcb....or contact them.....

  • @ravidomala1732
    @ravidomala1732 5 ปีที่แล้ว

    Iam fast dislike
    This is not wireless