How i can i decide the value if parameters r,f according to out run ohe(encrumbrance 500mm),M/L cantilever with encrumbrace 900,and X/O OHE with encrumbrance 1400.
i have made a video on ATD cutting, please watch it th-cam.com/video/Ix8LrchjsqA/w-d-xo.html Please Like and Share the video and Subscribe the channel.
pull off ya push off contact wire ki staggering k liye kiya jata h. Pull off k case me wire ko negative stagger diya jata h aur push off k case me wire ko positive stagger diya jata h.
There is no formula for calculating a amount of stagger, it is a predefined thing to protect our contact wire from wear and tear, but stagger should be remain in prescribed limits.
To clamp extend Long length stud about 8" from upside loomb to downside uplock nut 2nos to inside clamp lock nut each other after loose and reverse to upside
After certain time with some experience, people gain so much knowledge that they memorize for given implantation what will be the dimensions of tubes, but if you ask them how you guess that, then most of them will be unable to explain and will say "we have done so much work on site so we know what length tube to be use, you will also learn with experience".
itne saara formula koi batata bhi nahi hai na koi use karta hai waise hi kar deta hai log ye sab formula kaha se milta hai aapko aur ek cheez sir ye angle kiske kiske beech ka hota hai? SIR FOUNDATION PAR FULL DETAIL VIDEO CHAHIYE PLEASE
Bhot accha smjhaate hain..sir aap...🙌🙌🙌
Hey your work related to ohe Gyan is very good . Aapke Kam parshansha yogay hai . Keep it up.
Thanks
Super explanation sir. We want more videos on OHE. TRD its really helping.
Thanks
सर आप बहुत अच्छी जानकारी देते हैं
Thanks
Thanks Sir 👍👌
Make more videos
It is very helpful.
Thanks, next video is coming soon.
Very good teaching power
Sir bhut badiya bataya aapne.sare dout clear ho gaya
Superb artical. Good Luck.
Thanks
Thank you so much sir.. Plz upload more video.
next video coming soon
That was a great Lesson. But is this also applicable for Modified OHE bracket used is WDFC Railway? Does All those formulas applies as well?
bahut acha hi video. formula ka shortcuts be badadhejiye
just apply pythagorous theorem, you will get all values approximately
Plz make vedio regarding type of Mast & portal
Right
Sure, i will make a complete video on structures.
Bahut achha hai
Thank you sir thank you very much.
How i can i decide the value if parameters r,f according to out run ohe(encrumbrance 500mm),M/L cantilever with encrumbrace 900,and X/O OHE with encrumbrance 1400.
Hello sir. Kea aap bata sekte hai kiy avi ohe kaa kaam kaha chal raha hai.
Urgently
Sir please upload more vedioes the and psi related....
ok, more video are going to upload soon
@@railwayelectrificationohep7524 formula samajh nhi aaya L kya h
sir i am waiting for your new video kaha chale gaye hai
next video is coming soon
sir, where1.15m and 1.35m length steady arm is used.
Very nice video sir ...
Thanks
Bhai badiya keep it up
Thanks brother
Good explanation.
Very good style.
Can you suggest some book for OHE construction.
i think best book is ACTM
Sir kindly make a video on ATD Cutting and Adjustment of X & Y
i have made a video on ATD cutting, please watch it
th-cam.com/video/Ix8LrchjsqA/w-d-xo.html
Please Like and Share the video and Subscribe the channel.
Please make a video on BWA cutting
Ok, i will make a video on ATD erection and its adjustment.
@@railwayelectrificationohep7524 please make a video of ATD cutting not erection
Waww nice experience
Thanks
C ka lengths different imp may change hota hay keya
Reply
Different types of implementation may c ka valu kayse change hote hay
yes it changes, bcoz if you will fix it then how one can maintain proper dip
Track sempresan kaise lete h iska b video banao sir g
ok sure, i will a video on track separation also.
Plz make vedio related to sp ,ssp & TSS
Right
yah sure, i will make a separate video for each SP, SSP and TSS.
Sir, Pls let me know how the L , e, f,H values will come or how we hav to calculate
mail me, i will send you pdf
Sir kindly send me pdf then only I could understand calculation very well
Plz make a video on presag. Why presag given in ohe.
ok i will make a video on this
Curve ka cantilever assembly video example ke sath dijiye
Lsw wire ka drawing me use kaise hitahai
How to measure section insulator 1.45/1.65 m
By Track centre or track sepreation if any video regarding please post ,thanks.
ok, i will make a separate video on section insulator
@@railwayelectrificationohep7524 ha ispar ek video bana dijiye
Back to back cantilever assembly ka overview ....video demanded
ok i will make this very soon
super sir
Sir brecket pipe ka koi aasan tarika bataye
When i put data on B formula then 3.234 mtr is not coming. Plz solve my issue. Plz reply
It is a minor calculation mistake, it will come 3.230 mtr.Thanks for pointing it out.
सर tramway के braket की जानकारि दीजिये
ok i will make a video on that
i am in DFCCIL ,Jr./executive /electrical,my TRD training in Varodara yard
Push off ya pull of rakna hai ye kaise decide kare?
pull off ya push off contact wire ki staggering k liye kiya jata h. Pull off k case me wire ko negative stagger diya jata h aur push off k case me wire ko positive stagger diya jata h.
@@railwayelectrificationohep7524 0 mm stagger me Konsa dete hai? Pull of ya Push off
staggering contact wire k liye ki jati h aur contact wire me normally push off & pull off rkhna hi hota h,wahan 0 mm nhi diya jata.
Bhai ji ye BOOM ke upar isolator kyo banate h
Maintenance pupose ke liye, loop line wiring ko main line wiring se alag krne k liye boom pr isolator lgaya jata h.
Stager kese nikalte hai sir ji batwao
There is no formula for calculating a amount of stagger, it is a predefined thing to protect our contact wire from wear and tear, but stagger should be remain in prescribed limits.
To clamp extend Long length stud about 8" from upside loomb to downside uplock nut 2nos to inside clamp lock nut each other after loose and reverse to upside
Wow.... Muje iska pura derivation sikhana hai
Thanks, i will upload its derivation also.
Ok
Isme CM Mm ya metre me Lena main calculation karke dekha nahi aa raha hai
sir me Jo railway electrification ka logo h uske Karan bhut se value chip jate h ,Jo hum note down nhi kr pa rhe h
ok, in next video i will keep logo size relatively small.
Sir what is l in formula
Fully technical
OHE kitne type ki hoti hai
Super
Thanks bhai
Nice sir
Thanks
Sir overlap pr video bnao
Video on overlap has been uploaded.
Sir mujhe aapka namber chaiye
PTFE pe viedo bnao sir
ok, i will make a video on that also
Tnq sir
Sir or vedeo bnaye bilkul zero se btate chle than you sir
Next video is coming soon.
Tractors cultivation of soil plogh adgester arm
Good vedeo sir lekin in fourmulo ka use krte hue nhi dekha kisiko
After certain time with some experience, people gain so much knowledge that they memorize for given implantation what will be the dimensions of tubes, but if you ask them how you guess that, then most of them will be unable to explain and will say "we have done so much work on site so we know what length tube to be use, you will also learn with experience".
@@railwayelectrificationohep7524 right sir
@@railwayelectrificationohep7524 sir make video on Mast type,portal,TTC ,TTC boom length,SP,SSP,TSS etc...pls sir
itne saara formula koi batata bhi nahi hai na koi use karta hai waise hi kar deta hai log ye sab formula kaha se milta hai aapko aur ek cheez sir ye angle kiske kiske beech ka hota hai? SIR FOUNDATION PAR FULL DETAIL VIDEO CHAHIYE PLEASE
Angle is between bracket tube axis and the horizontal plan.
i'll make video on foundation also.
sir kahi recruitment hoga to bataiyega
ok, sure, 👍
simple caliculation bathayiye
for approx result, you may calculate by pythagoras theorem, also.
OU mast da assembly parts ka details do
ATD KA REAL VIDEO BANAYE SIR ATD formula bhej dijiye
ok, sure ,👍
ATD ka real video kab OHE
Or vedio bnao sir ji
Due to some issues, i was not able to upload videos, but now will continue...
Farmule me L Kiya hai
Bracket Chart chahiye
ok mail me, i will send you
I want to talking with you
Sir aapka mobile number chaye I am ohe staff central railway
Aur koi saral tarika hai nahi
use pythagorous theorem, you will get approx values.