Don’t give up your day job to be a dancer mate 😂😂😂 Well done on the build. Slow progress but very well detailed! I look forward to seeing the next one bud
I know what you mean but I am trying to keep as much of the original metal as possible and I couldn’t get under the car any further as I put the pallets underneath 😬
Can I ask what make of floor panel you used please?Just about to attempt the same on my MPI.Some of the panel suppliers web site are a minefield.Mine is exactly the same as yours for rot.keep up the good work.
They are magnum panels I believe I got them from m machine….. the only heritage panel I have used so far was rear valence, everything so far has just needed a lot of manipulating and a few bits added on etc but they are not as bad as I expected Thanks for watching
@@PocketRocketGarage thanks for your time and keep up the good work.These MPI minis don’t half rot.Just hope the near side is like yours and not as bad I dare not look yet lol.
Hi mate it’s looking great, I’ve just started on a 1996 SPI so following your project. What panel was your door step and quarter panel? I bought a magnum one and it’s an awful fit! Cheers, Matt
Magnum as well, I did cut it right down though as no need to cut so much fresh metal away on mine…. Still needed a lot of hammer and dolly work and a few good skims of filler and it should look good🤞🏼
@@PocketRocketGarage that’s encouraging thanks! The worst part looks like the radius of the bends on mine, they’re not tight at all not sure if I can fix that, yours looks nice and tight.
You have made a great job of the welding the door step is a tricky area to shape Hats off to you. Cheers Dave
Thanks Dave for watching , yes some smaller air tools would have been very handy!
Great work as usual Kevin. Glad you sorted the issue with the inner cill being short. 😎
Thanks Mark, I used some muscle and managed to adjust the panel as I welded it….. 🚀👍🏻
Don’t give up your day job to be a dancer mate 😂😂😂
Well done on the build. Slow progress but very well detailed! I look forward to seeing the next one bud
I was asked to go to dance school to be honest 👍🏻 but yes slow progress I know
Great job mate, well done.
Thank you! Cheers!
Great welding skills 👏🏻 👌🏻
I knew you were watching Sophie! Couldn’t resist 😁🚀
Cracking job. It’s taking great shape.
Thanks! Just a lot slower than expected
Brilliant work, Kev!
Thanks buddy! I am still going 🤪
Good stuff. Hope that the Michael Jackson tribute concert was also good. Best wishes.
It was ok that’s all I will say 😬
Great work mate, i saw you see light at the eend of the tunnel! You will get there!
Thanks! Yes still going at it
Nice work but why didn`t you put the whole floor panel in? Would have been all new metal then.
I know what you mean but I am trying to keep as much of the original metal as possible and I couldn’t get under the car any further as I put the pallets underneath 😬
Very good work mate . New subscriber . Where are you based ?
Hey Steve thanks!, based in Cambridgeshire
@@PocketRocketGarage can’t wait to see the updates .
Can I ask what make of floor panel you used please?Just about to attempt the same on my MPI.Some of the panel suppliers web site are a minefield.Mine is exactly the same as yours for rot.keep up the good work.
They are magnum panels I believe I got them from m machine….. the only heritage panel I have used so far was rear valence, everything so far has just needed a lot of manipulating and a few bits added on etc but they are not as bad as I expected
Thanks for watching
If you are on Instagram you can see more pics and follow the never ending battle against the rust 🤘🏻
@@PocketRocketGarage thanks for your time and keep up the good work.These MPI minis don’t half rot.Just hope the near side is like yours and not as bad I dare not look yet lol.
Hi mate it’s looking great, I’ve just started on a 1996 SPI so following your project. What panel was your door step and quarter panel? I bought a magnum one and it’s an awful fit! Cheers, Matt
Magnum as well, I did cut it right down though as no need to cut so much fresh metal away on mine…. Still needed a lot of hammer and dolly work and a few good skims of filler and it should look good🤞🏼
@@PocketRocketGarage that’s encouraging thanks! The worst part looks like the radius of the bends on mine, they’re not tight at all not sure if I can fix that, yours looks nice and tight.
@@PocketRocketGarage could I send you a pic to show you my concern? Get your opinion before I buy another panel?
@mattmillington6746 of course did me on Instagram @pocketrocketgarage