watched many types of machines and balancing, but my question now is can you balance a wheel dynamic and static balancing at the same time to have a best job ? If not why ? What is the difference ? Thanks for your reply.
James Malone My friend thanks for your reply ... but I don't know why some videos showed that dynamic does both calibration together vertical and horizontal, whereas static is only one type... even in some machines you can see illustration of the weights in sides of a steel junt t indicate static calibration ... and not in the center of the wheel... very weird !!!
I'd been did this steps as shone in this video but in the end always get Error 8 .. can you help me? even someone sent to me that there are fault in power card and needed calibration.
I'd been finished.... But I have a comment on the issue... The fault was the screen card and the agent was replaced it without knowing the basic cause of problem... which is some solt on the solder connective boints need to clean.
Simple super
Ouais super cool rien a dire j'aimerais bien apprendre plus
Please email to sales05@chinapuli.com for a solution. Thanks.
Comment reconnaitre la position exacte d positionnement de la masse d'équilibrage pendant l'équilibrage d'une roue
الحديد تطيح مع الوقت لازم تبديل تاير
watched many types of machines and balancing, but my question now is can you balance a wheel dynamic and static balancing at the same time to have a best job ? If not why ? What is the difference ?
Thanks for your reply.
You can only do one or the other. Static is single weight in center. Dynamic is a weight on each side of the wheel.....
James Malone
My friend thanks for your reply ... but I don't know why some videos showed that dynamic does both calibration together vertical and horizontal, whereas static is only one type... even in some machines you can see illustration of the weights in sides of a steel junt t indicate static calibration ... and not in the center of the wheel... very weird !!!
Went putting my machine on I hear a beeping sound and don,t work what what wrong
I need the bottom circus board.
How to choose the mode of S/1/3
Simple Good
Please email to sales05@balancer-sh.com. Our sales engineer will give prompt support.
how do you calibrate this machine
How much for machine
Please email to sales05@chinapuli.com for a solution. Thanks.
How to reset
How do you calibrate this machine?... I Have an Error 8 at end of self calibration .... What is means Pls?
I'd been did this steps as shone in this video but in the end always get Error 8 .. can you help me? even someone sent to me that there are fault in power card and needed calibration.
I'd been finished....
But I have a comment on the issue...
The fault was the screen card and the agent was replaced it without knowing the basic cause of problem... which is some solt on the solder connective boints need to clean.
Please email to service@chinapuli.com and Mark: from youtube. Our sales engineer will give prompt support.
Sir if machine is showing ERROR 5 what will be the problem sir pls reply as soon as possible
ERR.5:
Open protection before beginning launch
CAUSE：
a)Open protection
b)Faulty protection switch
REMEDY：
a)Close the protection
b）Replace the switch
Error 5 please help
Error 5 means the Protection hood does not lay down, if not , please check whether the microswitch of hood has problem
I have eror 10! Please help!!!
i think this model doesn't has error 10
Hey! Err -1- 😢 what this means?
Code:Err 1
Meanings:Main shaft not rotate or have no rotate signal
Cause:
1.motor fault
2.position sensor fault
3.power supply board fault
4.computer board fault
5.connection-peg untouched
Remedy:
1.change motor
2.change position sensor
3.change power supply board
4.change computer board
5.check cable connections
Ses a combien on peu payé cette apareil
Thanks for getting in touch with us on Messenger. Please send us any questions you may have or email to: Rebecca: sales05@balancer-sh.com
السلام عليكم عند وحد مثل عاطلت
3etini nimero ta3k
One piece
One piece price
Please email to sales05@chinapuli.com for a solution. Thanks.
عملية ضبط الماكينة لما تكون 0000
20g kér a külső oldalra a csávókám meg 30 rak és jó!:D