HOW TO REPAIR SOLDERING IRON | SOLDERING IRON NOT HEATING | REPAIR SOLDERING IRON DIODE | SOLDERING

HOW TO REPAIR SOLDERING IRON | SOLDERING IRON NOT HEATING | REPAIR SOLDERING IRON DIODE | SOLDERING
How do you wire a soldering iron?
Make sure your soldering iron is fully heated and touch the tip to the end of one of the wires. Hold it on the wire for 3-4 seconds. Keep the iron in place and touch the solder to the wire until it's fully coated. Repeat this process on the other wire.
Why is my soldering not working?
Heat is the number one reason that solder flows. Without it, you'll unsuccessfully try to solder a piece for a very long time. ... Just enough to hold it, but not to pull a lot of heat from it. If it's still not working, consider a charcoal block which reflects heat, making it easier to solder.
How do you test a soldering iron?
If the resistance measures correctly, the temperature sensor should then be measured. This measurement is obtained between pins 4 and 5 on the soldering iron receptacle and should be between 1.2 to 1.5 ohms. If any of these resistance values are incorrect, the heating element should be replaced.
How do you replace a heating element in a soldering iron?
Go ahead and trash the old heating element. Insert your new heating element with the wire end first into the soldering iron assembly. Then screw the ring back on. Use your fingers to separate the two leads of your replacement heating element.
Do you need flux to solder?
Oxides are formed when metal is exposed to air and may prevent the formation of good solder joints. The flux also protects the metal surfaces from re-oxidation during soldering and helps the soldering process by altering the surface tension of the molten solder.
What do you do when solder won't stick?
A classic reason solder won't stick to something is because you're not getting it hot enough. My interns come to me with this problem all the time. Make sure the tip of the iron is nice and shiny. Touch some solder on it, and it should melt almost instantly.
Why is my soldering iron not melting solder?
If it's not melting the solder, then the iron is not hot enough or even working. Try poking the tip through a piece of paper. ... The thicker solder requires more heat to melt. 40W is relatively low power, for thin solder it should work fine though.

[@sundark2472]

சூப்பர் அண்ணா உங்களோட பதிவு எனக்கு நீங்க ஹெல்ப் ஃபுல்லா இருந்துச்சு ரொம்ப நன்றி

[@vivekthekk]

No diode in my soldron

[@krishnagopalp7903]

Super sir

[@sathishkumar-om8dh]

Very nice but my soldering maxxpamma shock adikuthu any solution

[@kanisriram1625]

Super vazhthukkal 🍫

[@elakkiyaelakkiya6226]

Sema anna

[@karnanmech2101]

Bro new ah vaanguna 1 but 2 time's tha use pana athuku apram athula suthama heat varla

[@007lion4]

long life soldering iron types sollunga

[@sathishcsathishc7399]

ஐயா டயோடு ஷாட் தானே ஆகியிருந்தது அப்படி என்றால் அயன் கண்டிப்பாக சூடு ஆகும். டையோடு ஓப்பனாகி விட்டால்தான் அயன் சூடு ஆகாது. டயோடு ஷாட் ஆனதால் அயன் அதிக அளவில் சூடு தான் ஆகும். புதிய வர்களுக்கு தவறான பதிவு செய்யவேண்டாம். நன்றி 🙏.

[@einsteinsiva1560]

Konjam over bro diode mathurathuku 16mins videova
Video superb bro & more informative keep it. We are all support you

[@ECAREERPLUZ]

Thank you so much 🙂

[@krishsudharsun.l]

Sir what diode should we use

[@ECAREERPLUZ]

in4007 diode