2007-2010 Hyundai Elantra VVT solenoid replacement

แชร์
ฝัง
  • เผยแพร่เมื่อ 29 ต.ค. 2024

ความคิดเห็น • 28

  • @xBrendon
    @xBrendon 5 หลายเดือนก่อน

    Also works for the 1.6L, thank you!

  • @pedroj4230
    @pedroj4230 2 ปีที่แล้ว +1

    Thanks

  • @World-Superbike
    @World-Superbike 2 ปีที่แล้ว

    Do you, by any chance know precisely the timing settings for vvt intake cam and standard exhaust cam.. ? I've seen black link and 6 complete in between... 5 links between the lines... 6 links.... on and on.
    Any clues???

  • @WalterWhite-1957
    @WalterWhite-1957 2 ปีที่แล้ว

    Where would this be located on 07 sonata 2.4 i replaced the cam shaft position sensor do you know if my car even has one these sensor’s

  • @antonio1681
    @antonio1681 9 หลายเดือนก่อน +1

    Does the 4 cylinder only have 1 or 2 solenoid? I have a sonata 2010

  • @jasonn4597
    @jasonn4597 8 หลายเดือนก่อน +1

    Is that the same thing as oil control valve?

    • @xBrendon
      @xBrendon 5 หลายเดือนก่อน

      Yes

    • @metro7738
      @metro7738 13 วันที่ผ่านมา

      نعم

  • @PrinceLectro-qq8qj
    @PrinceLectro-qq8qj ปีที่แล้ว

    Greetings sir will this stop car from starting at all when it's broken ??? Pls reply me

    • @lestherlora2030
      @lestherlora2030 3 หลายเดือนก่อน

      Mines is broken and doesn’t want to start

  • @garnethart1137
    @garnethart1137 9 หลายเดือนก่อน

    Well which is it? Vvt solenoid like title says or vvt sensor like u keep saying in video?

  • @osmanali7578
    @osmanali7578 ปีที่แล้ว

    Hi ser in my car broke so can i do

  • @World-Superbike
    @World-Superbike ปีที่แล้ว

    Hello sir. I have a question.
    Do you know how the the OCV behaves on start up? I'm currently troubleshooting a persistent P0016 and have treble checked base timing which is perfect. I've replaced the Cam phaser on the end of exhaust cam. New Cam sensor also. Can sensor is good also but not replaced; pcm sees if it is left unplugged during startup and engine revs are affected accordingly.
    So, i removed the new ocv, plugged the hole in the valve tray with a rag and attempted a startup with ocv in the loom but out of the engine. I noted that it pulses during startup. Surely it should just retard during startup, and begin to advance around 1500rpm? Also.... can you please tell me ( if you know ) the amount of chain links between the mark on the vvt phaser and the inlet cam. This seems like a conundrum for all! Autodata says full link on timing mark on phaser, 5 full links and the next full link lines up with Mark on inlet cam. Hyundai Service manual shows 4 full links between. TH-cam diy mechanics have shown Seven! Links between. Out of some desperation i moved the inlet cam one tooth toward the Exhaust cam to have only Four links between. I had no P0016 on start and drive but the vehicle would not pull at all below 1500rpm... it just splutters! So you have any pictures of your cam phaser set up ??????
    I apologize for long message! Best regards, Eddie

    • @envricity
      @envricity ปีที่แล้ว

      Hello Eddie, sorry for not receiving answers. Unfortunately my son Steven passed away 5 month ago , it was his last video .:(((

    • @World-Superbike
      @World-Superbike ปีที่แล้ว

      @@envricity I am so very sorry to read this. Terrible news. What can I say or offer to you other than my heartfelt condolences and wishes.
      I am truly sorry.

  • @irisbaez1972
    @irisbaez1972 2 ปีที่แล้ว +1

    Tried to remove it and it was impossible. I just want to clean it but it was impossible to remove, so I just leave it along. Don't put problems where it doesn't exist.

    • @williamkrause5585
      @williamkrause5585 ปีที่แล้ว

      Oh now I see why you’re mad. Advice: you could just use a large pair of vice grip pliers to pull or twist it out, if you’re getting the same code. Then you’re not putting a problem, it’s just there already. Also no problem should belong anywhere.

    • @irisbaez1972
      @irisbaez1972 ปีที่แล้ว

      @@williamkrause5585 Mad? noooo. I never said that. Did you read my comment before replying? I just want to clean it as maintenance. I will not use a plier to brake it, I just want to clean it.

  • @nanaboakyejnrkingdavid4357
    @nanaboakyejnrkingdavid4357 ปีที่แล้ว

    My name is David and I'm from Ghana and I wish I could work for you

  • @irisbaez1972
    @irisbaez1972 2 ปีที่แล้ว +1

    How did 2009 have this problem? Mine 2008 has 156K miles and is still new. Advice: You are there already, why not clean the connector and use dielectric grease?

    • @stevensgarage7284
      @stevensgarage7284  2 ปีที่แล้ว

      The connector was already clean and still had some grease on it. Seemed like someone had already replaced the sensor then broke it.

    • @irisbaez1972
      @irisbaez1972 2 ปีที่แล้ว

      @@stevensgarage7284 Hi. What about cleaning that? if it's good can I clean it?

    • @williamkrause5585
      @williamkrause5585 ปีที่แล้ว

      @@irisbaez1972 Are you giving advice or asking for it?

    • @irisbaez1972
      @irisbaez1972 ปีที่แล้ว

      @@williamkrause5585 are you Steven's Garage?

    • @metro7738
      @metro7738 13 วันที่ผ่านมา

      هل يسبب في عدم استقرار المحرك