LS head bolt torque
ฝัง
- เผยแพร่เมื่อ 17 ต.ค. 2024
- Joe Cabral showing the proper torque sequence and proper torque of GM LS head bolts.
All of Engine Quest LS Head bolts
Chevrolet Ls Head Bolts Set 2007 - 2016 4.8, 5.3, 5.7, 6.0, 6.2 - Part #EQ-HB349NC
enginequest.co...
Chevrolet Ls Head Bolts Set 2004 - 2010 4.8, 5.3, 5.7, 6.0, - Part #EQ-HB349NB
enginequest.co...
Chevrolet Ls Head Bolts Set 1999 - 2003 4.8, 5.3, 5.7, 6.0, - Part #EQ-HB349NA
enginequest.co...
Good job big bro I just did mine watching you 💪💯
No BS , to the point , thank you and subscribed
Dude thank you for this. Really needed this
hi this is the aluminum engine of the GM 2007 to 2013. ??????
Best video i seen so far 👍
its always good to put a white mark top edge of bolt just to let you know there all torqued right.And none are missed.
thank you so much. you made it so frigging simple.
best video i seen so far thanks
As a cylinder heads up, factory recommends torquing 1-10 first. 22lb, 90*, 90* (50* on the 9 & 10 if you have 1st design heads with 3 bolt lengths) THEN taking 11-15 to 22ft lbs.
Stewart Chen either way those bolts are tighter than dicks hat band lol
Great job. Really appreciate this. Be blessed Richard Iowa
Thank you very much . No one could do that better .you are the man .
Would this work for my 6.2 engine? I have a 2016 c7 stingray
When I put my arp head bolts in the instructions said to get your bigger bolts torque sequence done first then do the smaller upper bolts last .. is there a difference in the procedure from arp and oem?
No I think it’s the same procedure I think he just did it wrong. You’re supposed to torque the small ones after you have taught one through 10 and then you torque the top ones to 22 lb
Yup, the top bolts will loosen big time after torquing all the others.
Are you doing this on an aluminum head and aluminum block?
Did you waste good bolts for this video? I noticed you didn't have valves in the head so it had to come back off.
noticed that as well
This ls engine you can install the valves through the spark plug holes
@@tomaszszymczyk5246 lmfao
@@tomaszszymczyk5246 what??
Nice video, what lube did You use for the bolts?
The bolts come pre lubed so to speak
Please give this man some modern tools ! Great video!
No shit 😂😂😂😂
I prefer my torque wrench like that
He knows what hes doing.
Uh, that style torque wrench is the most accurate
Is this the same for flex fuel ls gen 4 aluminum 5.3 block n 243 heats!?
Thank you for keeping simple.
Excellent tutorial
Is this the same for L76 heads?
Hola que tal tengo varias preguntas Tu crees que se muy inportante poner los tornillos nuevos ? Y por que es que muchos torquean en grados y otros en libras ? Saludos y todo el equipo tecnicos en unos dias enpezare a armar mi motor y este video me va servir mucho
Si, es mejor poner los tornillos nuevos..ya bienen con la pasta para que permanezcan firmes.
Awesome video. I’m happy now knowing I did it right lol.
Thank you very much helpful explanation 🤙🏼😘
that is your torque sequence...and that concludes your heavy resistance workout for today......and the next few days...
When are you going to put the valves and springs?
4:10 he’s saying 22, I’m reading 10 off the dial.
Excellent ...Excellent explanation
Is this the same torque sequence on a 5.3 truck engine
Believe so if it runs the three different length bolts like the LS1.
Thank you!
how you going to install the valves ? lol
Great video 👍
A long string of robots install bearings, hydraulically press cam bearings in, install rings, then rod caps, head gaskets, photo confirmed, head installed, dry bolts installed and one machine tightens all in one shot. Everything to complete engine behind glass. The only techs wore with suits and loaded trays with parts, never touched by humans until ran on natural gas for 10 minutes at 2K RPM, stamped, yellow marker, sheet wire-tied to dip stick tube then last robot picks it up & places in plastic create to truck to the assembly plant. Even GM eSI points out "Dry" bolts for repair in the field. Been there, saw that! Both iron & Al. blocks identical. Oh yea, the heads came in fully assembled with valves. Retired ASE Master Tech / Contract labor for GM at the time.
Now how do you get our valves in with the head on? 😂
Without the pistons in reach up through the cylinders with the valves of course. LOL.
🤔 X2
@@deegan727 good luck getting the pistons in
Rock Roll Squeeze one ring at a time. All jokes of course.
Lol
Someone get this guy a impact
Don't trust em
How show me how to do it whilst motor is in the car
So what's the actual ft. Lbs. When done?
If you don't want to buy the angle meter I think you can buy arp head bolts and they'll give you the pattern and tork numbers for each pass
Pound Feet
Is this the same for the LS3 engine and heads
Great video! Thank you sir!
Greatest video ever thanks brother
Thank you so much.
Thanks for video
thank you very helpful im doing heads on my ls
What about 05 Ls 5.3 would it be the same?
is the first torque inch pounds or foot pounds.
Big bolts are FT pounds (22ft lb, 90 degree, 90 degree, little bolts up top are also FT pounds (22).
This guy torque all bolts to 22 ftlbs including 8 mm bolts others say the 8'll bolts are last to torque 22ft lbs . Who's right ?
The book says 8m bolts get torqued down last
He's wrong. It must be his rings.
Summit day torque specs are 22ft pounds/90 degrees/50degrees not 70
What's that tool called with the degrees on,it?
Torque Angle guage
He dont need modern tools, he needs some WHEATIES !!
All the grunts and groans yielding 11mm bolts
How about the top bolts?
They stay at 22ft. Lbs.
I wonder how long it took him to realize he didn't have any valves installed.
Cuestión. This is for 5.3 liter flex fuel. 2007 Silverado. Good morning
Does he realize that he does not have the valves and springs in it...
🙏🏽🙏🏽
Farted at 35°.
Jk..
Great video
this is for any ls?
1997 - 2004 model years
my 2000 formula 5.7 has a noise I think it's a lifter your video will be very helpful thanks
Do 05-07
What about the mains
Homeboy can't even read his own torque wrench. What he thinks is "22" is around 13lbs. I really hope he's not taking anybody's money for this level of work.
If the valve spring was there you couldn't use that angle thing.
Yes you can. I’ve done them with the autozone torque angle guage on 4 different LS engines. Just gotta pay attention is all.
Couldn't you find the torque at 90 degrees , ? Why wouldn't every bolt be the same weather ... either 90 degrees or the said torque , Apple's ARE Apple's. I don't understand this method ,
Bolt design and accuracy
Where are ur valves
Gruntin and groaning yielding 11mm bolts
Makes me anxious. Haha
I believe factory says to torque the small ones last you’re gonna have to retort them once you do the other two steps, but I think you did it wrong but whatever it’s a five-year-old video so
why hasn't anybody figured out the torqued spec on 90 degree turn, and 70 degree turn?
I know right!!!
Because they're torque to yield bolts so there is no torque spec on it they stretch you cannot reuse the bolts
Because 90 degrees is literally an L. You don't need an angle meter. Lol
i thing you forget the valves lol
Probably just building a display engine
Cardio may need to be added into your weekly routine... and breathing treatments may be of interest as well.
Videos went black
I just did 22, 50, 70. Simple
I was nervous watching
So a 1/4 turn.
Where are the valves lol
Book calls for 90 and then 50 not 70
Ñ
Would not let this guy work on my engine, i feel like he did this all wrong. Maybe its just me.
It’s you. That just the way it’s done.
It’s just you.
Sounds like someone needs to retire
Its useless
How about a ratchet. Ridiculous video
Don't see the valves