Wow I finally got through the first what, 15 videos if you include 5C. I thought this one was very easy to understand, but maybe it is just because it is starting to sink in. I am assuming you are doing these for students of your class and not the general public, but I have have learned a great deal and am looking forward to the rest of your arduino videos. Thanks much!
Very well presented. I learned a ton. I am trying to use SPI on ESP32, so if I have only one TFT connected and know which in is MISO, MOSI, CLK, then I only have one pin for CS (chip select) can I use any digital pin and name it in the code? Or do I have to know the pinout number on the data sheet (that I do not have)?
Hi, many questions in the web about how to connect and addressed two I2C device (such sensors) in the Arduino, hope you can make a follow up part on this for I2C. I love your video because it tackles the very fundamentals that most of us jump over, but these can be great with further demo. Thanks, more power!
Hi there, very good video overall, but I would say give a bit more explanation on the code if you are going to include it. Does the MSTR, SPE and SPIE represent single bits (just set to either 1 or 0) or are they in the form of MSTR = "00010000", SPE = "01000000" etc. (42:19)
Sr, HELP ME, PLEASE!! I would like to send words across serial monitor. For example: I write "on" and the LED will turn on but if I write "off" the LED will turn off. Do you understand me?. My english is not clear, sorry, but I need your help
hi..sir , can you tell me 1.how to interface with micro-controller (arm7) and micro-processor (arm9)? 2. how to write c/c++ programmer for both micro-controller (arm7) and micro-processor (arm9)? 3. what to make client device driver and master device driver ? plz replay me ::::::::::::::::::::::::::::: :) thank you very mach..
i2c and spi hi..sir , can you tell me 1.how to interface with micro-controller (arm7) and micro-processor (arm9)? 2. how to write c/c++ programmer for both micro-controller (arm7) and micro-processor (arm9)? 3. what to make client device driver and master device driver ? plz replay me ::::::::::::::::::::::::::::: :) thank you very mach..
There are two aspects of interfacing: Hardware and Software. The hardware interface is the same for any microcontroller. The software connections depend on the programming instructions available on the microcontroller. While you can make a micro controller into a slave, it is usually set up to be the Master. As for the ARM 7 or 9 processors, I have no experience.
Wow I finally got through the first what, 15 videos if you include 5C. I thought this one was very easy to understand, but maybe it is just because it is starting to sink in.
I am assuming you are doing these for students of your class and not the general public, but I have have learned a great deal and am looking forward to the rest of your arduino videos.
Thanks much!
showwww!!!U am Braziliam and you speach is very friendly to me understending!!!Go ahead!!Thank you
thank you sir...learned a lot from this video.
Muchas gracias amigo.. me gusta mucho la manera en la que realizas la presentación.
Thanks! The lecture is very easy to understand!
good lecture and I have cleared basics of spi and i2c
Hey I'm from myanmar, Thanks alot for your video. I love it!!!!!
Very nice lecture! I am SW guy and I was looking for this kind of online training. Thank you!
Great video Robert!
It's a useful tutorial. I love it.
Very well presented. I learned a ton. I am trying to use SPI on ESP32, so if I have only one TFT connected and know which in is MISO, MOSI, CLK, then I only have one pin for CS (chip select) can I use any digital pin and name it in the code? Or do I have to know the pinout number on the data sheet (that I do not have)?
Hi, many questions in the web about how to connect and addressed two I2C device (such sensors) in the Arduino, hope you can make a follow up part on this for I2C. I love your video because it tackles the very fundamentals that most of us jump over, but these can be great with further demo. Thanks, more power!
Thanks for your input. I'll probably tackle this next.
very good,introduce very detail.
Hey Robert, you're videos are great. Just wondering if you had any information about easy to use GPS modules?
Hi there, very good video overall, but I would say give a bit more explanation on the code if you are going to include it.
Does the MSTR, SPE and SPIE represent single bits (just set to either 1 or 0) or are they in the form of MSTR = "00010000", SPE = "01000000" etc. (42:19)
hi sir +Robert Paz i need help. i want to handle two wii nunchuk using a single arduino board. so plz help me.
thanks robert!
why does i2c only allow 127 and not 128?
its 0-127 not 1-128.
Sr, HELP ME, PLEASE!! I would like to send words across serial monitor. For example: I write "on" and the LED will turn on but if I write "off" the LED will turn off. Do you understand me?. My english is not clear, sorry, but I need your help
If I understand you, you would like the Serial Monitor to display ON when say, Digital pin 3 is LOW (assuming the LED is active LOW). Is that correct?
I want to wirte "on" and turn on a led and I want to write "off" and turn off it (wirte "on" an "off" in the serial monitor text chart)
How do i implement a VGA controller using atmega328p
Gosh, you seem so hesitant and under-confident. Have confidence in yourself if you understand the material.
how to read slave data in spi
Sir could you make a video on how to use it and demo so we know how is it implemented. Thanks for the video though :)
Check out my Hands On Arduino videos 4 & 5.
i learned something
merci
oberek92 ļ
hi..sir , can you tell me 1.how to interface with micro-controller (arm7) and micro-processor (arm9)?
2. how to write c/c++ programmer for both micro-controller (arm7) and micro-processor (arm9)?
3. what to make client device driver and master device driver ?
plz replay me ::::::::::::::::::::::::::::: :) thank you very mach..
12:47 I2C master doesn't need an address
i2c and spi
hi..sir , can you tell me 1.how to interface with micro-controller (arm7) and micro-processor (arm9)?
2. how to write c/c++ programmer for both micro-controller (arm7) and micro-processor (arm9)?
3. what to make client device driver and master device driver ?
plz replay me ::::::::::::::::::::::::::::: :) thank you very mach..
There are two aspects of interfacing: Hardware and Software. The hardware interface is the same for any microcontroller. The software connections depend on the programming instructions available on the microcontroller. While you can make a micro controller into a slave, it is usually set up to be the Master. As for the ARM 7 or 9 processors, I have no experience.
+Pallikonda Ramu : www.codesforprogram.blogspot.com
nothing is understandable,...use some easy way
I'll do what I can in a follow-up video.
What's not to understand....it's very helpful.
Robert, the material is fine. You can't help it if the people have no basic understanding to start with.
Worst. Teacher. Ever.