Yes, the techique itself is not complicate, but just time consuming, but it makes you feel good when you finish and get a good result, right? Enjoy~~ I myself used also around 2 hours to get all 6 piece done, and cost me 2 days for design pattern only on the hands
@@studioFO haha yes, I do enjoy the 2 lines I added hahaha, but I find it hard to do on small parts, my tape isn't sticky enough or I'm scared it moves... My first attempt I used too much pressure and the lines were wobbly T_T
@@yunkil yea... I also have the same problem even I did it many times, suggest you can use less glue to make it stay on the kit first, then apply more glue in this case you don't need to press it hard to keep the correct position
![[ENGSUB] UNPRODUCTIVE DAY ใช้ชีวิต (เปื่อยๆ) ด้วยกัน 1 วัน! | OUROAD CLOSEFRiEND SS2 EP.9](http://i.ytimg.com/vi/pyYKZ3kra9w/mqdefault.jpg)
想請教下，如果想令膠板同模型件有無縫效果，例如想有高低差嘅感覺，係咪都係用紫蓋膠水都OK，定係另外要用其他方法
可以用aa膠做無縫，如果個gap真係好大的話
請問
本片示範的肩甲明顯為曲面
完全平面的膠板
是如何服貼於曲面的？
硬黏嗎? 還是用熱風槍
若用熱風槍吹，又是怎麼依曲面形狀調整的?
熱風吹到軟→彎曲→拿去曲面貼貼看 重複這個步驟嗎?
可是能調整的時間很短，而且膠板往往變得太軟
還是 直接拿膠板貼著曲面零件 吹熱風
溫度適當時，只有膠板會軟化 而零件比較耐熱？
(實際試好幾次，都無法將膠板貼於曲面，硬貼後來又會跳起來...)
好問題，第一只可以用比較薄身的膠板，另外真係太彎的話我會分開細塊細塊做唔同分隔而唔會傾向一大片咁上 薄身去到一定的面積之前都可以硬黏
@@studioFO 感謝您的建議，很棒的參考方案
想請問，點樣先至可以避免到好似片裏面咁樣唧咗啲膠出嚟
另外呢我唔知點解，貼咗塊膠板上去，諗住沿邊刻線，發現條邊吾直，條線攣咗🥲
只要唔好用力壓由得佢自然粘死就可以，咁你等佢第一次粘死後再補膠水粘埋其他邊（如有須要）
咁好大機會係膠片本身個邊唔直，我自己會係未貼之前刻左線先的
@@studioFO 但係我有個疑問想請教下，如果個面本身唔係平面，有啲微曲，咁唔係要壓一壓塊膠片先至貼服到咩，定係有咩解決方法？
@@kenchoi392 咁可以先粘一邊，等佢乾再粘另一邊，用已粘死的一邊借力就會少d溢膠
想問如果想做立起嘅型態，膠水可以點癡？
如果係我理解岩的話，你要挖空個膠件塞入去俾足夠支撐，淨用膠水都幾肯定會甩
支持你👍🏻
感謝！！！
請問點樣先可以將啲膠板切落嚟，切得好整齊
想問多句hg 用幾厚膠片好？
切就可以先用0.15訂線刀刻好先用界刀切斷。
幾厚就真係要睇你自己要點改了...
用界刀係咪比用推刀好？
@@benhung1987 界刀太尖, 第一刀同第二刀係有機會唔一定對岩個切口. 如果用刻刀先開左坑就至少有一邊係一定岩. 但你都可以自己先試試. 呢個係我的習慣only
Thanks for sharing, I was doing something similar last night, took me hours to make simple shapes haha
Yes, the techique itself is not complicate, but just time consuming, but it makes you feel good when you finish and get a good result, right? Enjoy~~ I myself used also around 2 hours to get all 6 piece done, and cost me 2 days for design pattern only on the hands
@@studioFO haha yes, I do enjoy the 2 lines I added hahaha, but I find it hard to do on small parts, my tape isn't sticky enough or I'm scared it moves... My first attempt I used too much pressure and the lines were wobbly T_T
@@yunkil yea... I also have the same problem even I did it many times, suggest you can use less glue to make it stay on the kit first, then apply more glue in this case you don't need to press it hard to keep the correct position
@@studioFO thank you for the tip!!
想請教一下，點樣可以係一個有弧度既件上面加膠片呀，例如好似你條片最後面既紫色件咁，thx
我係你另外一條片睇到了，謝謝
整得很好，實在太強了
@@nailcwb 呵呵, 我岩岩先睇到你留言, 如果仲有問題的都可以再問.
講多句, 如果真係好弧, 可能你要用風筒加熱等佢變軟先再上. 問題係呢個方法未必用得到係厚過0.5mm厚的膠片上, 因為我只做過0.5mm
@@studioFO 唔該曬你😀
很專業喔
呵呵, 謝謝
我用雙星淺綠色extra thin cement 可以代替紫蓋膠水嗎？
如果係abs膠痴gundam件就唔建議，應該會痴唔到的.
郡士紫盖胶水可以粘abs胶板吗？
快d講噴油
因為我租人地場噴only... 係人地個場拍自己野會老尴wor... 我想下辦法！