This is a 2-year old video, so perhaps you know this already, but the leaking sensor is fixable. Just remove the top section (2-screws and it slides out) and then the tank comes out with just 2 more screws. Undo the strap clamp, remove the sensor, silicon the fitting, let dry, and reassemble.
@ 7:30 - pull out the drill and pop a hole in that plastic housing so you can access the hard to reach screw. I doubt one small hole would compromise anything
I have a problem with mine where it leaks in an area behind where the kcup goes. Now is all rusted. I need to open it and see why is it leaking from the top. I don't have a clue what I am doing. Thanks for the video. this will help.
Have a k80 My problem is the part you open on top to put the k cups into is all floppy and doesn’t move like it should, also sometimes it binds and I have to move it around by hand til it sits mow normal and kinda have to push the lid down HARD(probably breaking more stuff in the process). If I shake the machine there’s clearly something broken and rattling inside…(even before I had to press and move thing around by hand)
Yesterday I took apart my Keurig for deep clean and over torqued one of the three screws on the tanks diaphragm cover. The crack didn’t extend through and I’ll monitor it but it’s about 1”Lbs of torque needed and I did an 10”Lbs if torque. To clean this one need to take apart the whole system
Help! Our K-Select stopped working after descaling. We've disassembled it but can NOT find the thermal switch to reset it. Any suggestions? Thank you so much for your videos.
Thanks for the video. Mine is leaking from the bottom as well. I suspect it’s from the same place. But also, the machine just started brewing very weak coffee. The needles are free from obstructions and it’s been descaled. Do you think that it’s possible related to the leak? Thanks For your time
So the power went out at my house due to a transformer blowing across the street. Took my 4 y/o completely out of commission so I’m going to try to check it out and see if it’s salvageable because it wouldn’t been headed to the dumpster anyways.
Hey “Just A DAd” I picked up a Red Keurig K-Select Single K-Cup, it look like it’s never been used but there’s no power, won’t turn on. Have you dealt with this issue yet? I’ve been searching for the last 3 hours and the only thing I’m finding is resetting the thermostat after descaling. If anyone has any idea what the problem may be reply back…thanks!
Incomplete video. You did not show how us how to remove the heater tank subsequently you did not fix the leak. Mine also leaks and it's probably from the tank but your video only gets me half the way towards fixing my Keurig K-80.
How to clean check valves because only half cup brews. Clean all needles etc but no luck! Thanks for your videos!
Thanx
Welcome
Nice pace. Well done
Thank you
This is a 2-year old video, so perhaps you know this already, but the leaking sensor is fixable. Just remove the top section (2-screws and it slides out) and then the tank comes out with just 2 more screws. Undo the strap clamp, remove the sensor, silicon the fitting, let dry, and reassemble.
Great video! I needed to change the power cord to a longer one and your video helped me in disassembling the unit. Thanks!
Your so welcome!!!
@ 7:30 - pull out the drill and pop a hole in that plastic housing so you can access the hard to reach screw. I doubt one small hole would compromise anything
I have a problem with mine where it leaks in an area behind where the kcup goes. Now is all rusted. I need to open it and see why is it leaking from the top. I don't have a clue what I am doing. Thanks for the video. this will help.
Sorry to hear that! Good luck with it! let me know how it goes and Good job for even trying to do this!!!!
Have a k80
My problem is the part you open on top to put the k cups into is all floppy and doesn’t move like it should, also sometimes it binds and I have to move it around by hand til it sits mow normal and kinda have to push the lid down HARD(probably breaking more stuff in the process). If I shake the machine there’s clearly something broken and rattling inside…(even before I had to press and move thing around by hand)
Yesterday I took apart my Keurig for deep clean and over torqued one of the three screws on the tanks diaphragm cover. The crack didn’t extend through and I’ll monitor it but it’s about 1”Lbs of torque needed and I did an 10”Lbs if torque. To clean this one need to take apart the whole system
Help! Our K-Select stopped working after descaling. We've disassembled it but can NOT find the thermal switch to reset it. Any suggestions? Thank you so much for your videos.
Thanks for the video. Mine is leaking from the bottom as well. I suspect it’s from the same place. But also, the machine just started brewing very weak coffee. The needles are free from obstructions and it’s been descaled. Do you think that it’s possible related to the leak? Thanks For your time
It could be just a tube that come off or is leaking, It might be worth opening it up.
My keurig supreamplus stuck in descale.
This could be a known issue Keurig has with this model of Keurig. I would call Keurig Customer Care at 866-901-2739.
So the power went out at my house due to a transformer blowing across the street. Took my 4 y/o completely out of commission so I’m going to try to check it out and see if it’s salvageable because it wouldn’t been headed to the dumpster anyways.
I have a K80. Power button is stuck in the pressed position. Hard to take that top portion off. Please help thank you
Are… are you John Cusack lol?
Funny!!! lol
Hey “Just A DAd” I picked up a Red Keurig K-Select Single K-Cup, it look like it’s never been used but there’s no power, won’t turn on. Have you dealt with this issue yet? I’ve been searching for the last 3 hours and the only thing I’m finding is resetting the thermostat after descaling. If anyone has any idea what the problem may be reply back…thanks!
Mine doesn't turn on at all. Just over 1 year old so out of warranty. Is there a reset that I can do so that I can turn on and brew coffee again? 😂😂😂😂
Incomplete video. You did not show how us how to remove the heater tank subsequently you did not fix the leak. Mine also leaks and it's probably from the tank but your video only gets me half the way towards fixing my Keurig K-80.