How to wire a 3d printer arduino RAMPS 1.4 A4988 stepper motor driver
ฝัง
- เผยแพร่เมื่อ 14 พ.ค. 2016
- How to wire a 3d printer adruino RAMPS 1.4 A4988 stepper motor driver
You get all the parts fom here gearbest.com/electrical-tools-c_11347/?lkid=15838445 whit coupon :ONQQGY2KCC with 6% off
3d printer giveaway on 500.000 views, you must share and like this video to enter the giveaway. Good luck www.gearbest.com/3d-printers-...
how to wire a 3d printer,
3d printer arduino,
3d,
3d printer,
printer ramps,
ramps,
a4988,
driver,
stepper motor,
printer stepper motor wire,
ardunio,
arduino ramps,
arduino mega,
arduino mega 3d printer,
wire arduino mega,
ramps 1.4,
ramps ardunio printer, - แนวปฏิบัติและการใช้ชีวิต
Seriously this should be the number one video for ramps!
that is the best illustration I have seen for wiring ramps thanks :)
You have every board backwards on top of the ramps at 42 seconds. It is a good thing i saw the writing on the bottom of the drivers that told me what pins they needed to go to.
best info out there, thanks very much for sharing. awesome!
perfect, thanks !
Hello! Simple and easy to follow, thanks.
With this arrangement how do you wire the fans?
So cool !!! thanks
Thank you so much
Hi,
I have a question about the building from scratch 3D printer. for my idea, I would like to have 4 PMW output to simulate the extruders as I am using actuators that need this type of signal. So my question is, Can I use 4 pins on the RAMPS board and assigned as extruder on the Marlin firmware and when I slice the design using Slic3r with the 4 different colors I would be able to activate this 4 pins with PMW signals when the Pronterface perform each extruder?
Hope this question makes sense and I could hear soon from you. Really appreciate your content.
Thank you.
Bro it was good.....but need more help . new with this stuff but could you look forward related to marlin.. with RAMPS 1.4..
Hi, I have two question.
1) Why are there two holes for power supply 1:04? I know the two below ones (Hot and Ground) are for Motor. How about the above ones because when I applied the power supply to them, there's nothing happened?
2) How much voltage do you recommend for controlling 5 stepper motors simultaneously? When I applied 17V to control 2 stepper motor, they ran pretty smoothly. But when I hooked up one more motor, it started to mess up. It appears that at 17V, the board cannot handle 3 motors or more.
Thank you.
thanks very much
The heat bed is powered through the 11 Amps connection. The 5 Amps is used for all the Arduino and the stepper motors etc.
thank you
Are the stepper drivers on back-worth on the first picture? 0.43
yes
Ești din Romania?
👍👍👍😊😊😊
well it work for a monoprice mp select mini 3d printer
What software are you used in this video firtzing?
Can it be used for 5 axis router ?
what is the max power input for Ramps in :
Volts =
Amps =
Can i replace my mks gen board from sunhokey prusa i3 with this one without instalking firmware
Can we use tmc2208 or tmc 2209 with this one ?
can not you please write links to the stuff from which it is compiled? so I can order right .... so kind of an amateur and I'm afraid it's complicated :)
very nice video,
i am a rookie in 3D printing so......
why do we need two extruders again, as it said in the video above "extruder1" and "extruder 2".........................any type of help is appreciated
Vyom Rajan Singh you dont need 2 , but there are printer whit 2extruder to print whit 2color
ohhhk thankyou calin
i want 2 motors into x ax is ,is that possible with the extruder motor 1 port location ?
In the beginning on list of what you need wires are not listed nor do you specify what gauge wire is used like heater bed 12 gauge wire or extruder wire 22 gauge etc
I thought using one driver to power two steppers reduced current and torque by a little more than half, meaning it would be better to use one or abandon extruder 2 and use as z2?
It's probably better to have a separate stepper drive for each stepper motor, but many 3D printers have two Z axis steppers connected to a single stepper. It is actually possible to stack two steppers for Z axis, if you desired to do so.
What about the jumpers under A4988 are there all installed?
good question where do the jumpers go?
on top of shield bord conectors u place driver modules
Mike Menci wait, what are jumpers?
jep
Mike Menci all jumpers
Hi, I'm using nema 17 for Z axis,
For DLP 3D printer, what power supply should I use?
Thanks
the controller with the stepper motors need ~90W adding to that around ~40W for nozzle heating element. The heating bed needs at least ~100W to heat the bed fast. So, that would mean 240W would be good. If you have no heating bed, you can go with ~160W.
Thanks for the info
This video is called tutorial video.
Complete detail.
Do you think you could show us how to set up two stepper motors with a single nozzle I’ve been trying for three weeks and I can’t figure out the firmware or the slicing software
can someone please explain the correct color coding for the steppers what i have is blue-red-green-black sequence left to right, as i have looked over and over on the ramps photos. my motors are moving but i am having problems with aligment.
you must check the the wiring rezistance search on youtube
Can some one tell me where to get code for upload to arduino board. Video show only wiring diagram. No detail where to get code.
i need controller printer inject from arduino what?
Helloo i vant to make 3d printer with this electronic but i want to connest 2 motors to y axis not z iz it possibile or no?? Thanks..
Yes it is ok
Still doesn't show how the drivers should be installed. They are not all created equal so it would be nice to show that.
There are some errors in this video. Check out official ramps website for facts.
which is best dc voltage of input current is best for this 1.4 ramp.........
i doing project of 3d printing
3D MAKER 12v dc from pc power suply
watss plzz
3D MAKER TAMIL i use 450w pc power
photo plzzz
I connect that power from psu.using 10 to 15 my arduino mega voltage regulator is burned
Why there are two power supplies???
There is an 11 amp and a 5 amp terminal. The 11 amp terminal powers the heated bed and the 5 amp terminal powers everything else. If your power supply only has two wires, run them to the 11 amp terminal and use small pieces of wire to connect the 11 amp terminal to the 5 amp terminal (positive to positive, negative to negative, of course!). If you don't have a heated bed, you don't need the 11 amp circuit at all.
micvee where would you recommend I put my earth cable?
we are working with DC, so you will only have 2 wires. ac has 3 and that goes to your power supply
why 5 motors? X, Y, Z, EXTRUDER, and whats the 5th one for?
Tech The Trucker its a second hotend for bicolour printer
Actually in his picture he is using 6 motors (x, y, two z axis and two extruder). Does the z-Axis really need 2 motors?
It depends on the printer... A Prusa style 3D printer has two Z axis steppers and is one of the more common printer designs. If you have that style of printer you need both Z axis steppers.
I did every thing right but ended up firing Arduino 🙃
In what way is that RAMPS card photo showing anyone how to correctly install the stepper drivers the right way round?!.Ah! ANOTHER Photo. Hurray. So what was the first photo for exactly??
لو سمحتولى ترجمولى افيدوني افادكم الله
the power is 12v or 5v?
12v
ok
I have put 12v the new ramps 1.4 that came to me and burned again. which
can happen to be of poor quality, because well conctado was, two wires
from the power supply to the ramps and nothing else, and burned
You can make a video for imbeciles. Thank you
What is a heat "bead"? LOL
wats the music name?
soundcloud.com/zoravenka/fascinam
input power is ? v and a
replay any one
3D MAKER TAMIL pc power suply
no.my qutn is input v of ramp 1.4 or..........out put v and ahms of power suply
can i use arduino uno instead of mega?
no the uno got to little i/o's
+Marco Mayer can u Make a video for arduino uno pls..
Музыка то нахрена
i dont understand, iv done all the wiring correct (i think) but yet it doesnt work for me. if anyone can help me, maybe skype with me so i can show you please help... i really want it to work :( my skype name is dontstopbelieveng
whenever i finally fix the problem ill edit this comment so if you're reading this its still not working! thanks
Hello , Tell me if you solved your problem .
miratehnicbc I did, I bought a new 3d printer that was fully assembled lmao
I m faceing your problem with a cl-260 and I was wondering if you can help me
miratehnicbc unfortunately I "fixed" my problem by returning mine and getting a monoprice makers select (prusa i3 clone)
your diagram shows a completely wrong wiring for stepper motors so im not even going to bother watching the rest of this video....take time and ensure your graphics are correct and accurate before adding to the rest of the ill experienced crap people are flooding the internet with, if you dont know what youre doing dont make a video about it we need real tools to help us not idiots who cant even get the right pin out for an industry standard part right
The biggest problem with this video is that it implies that there is one correct way to wire the stepper motors for all 3D printers. If you invert the wires (red stepper wire on pin 1B rather than 2B, for instance), the only thing that happens is your motor spins the opposite direction. The fix is to simply flip the stepper motor connector 180 degrees, or invert the stepper in the firmware settings.
stupid music in all videos
sounds like the music is more important than the information you trying to impart so THUMBS DOWN
I FRIED MY DRIVER BASED ON YOUR BAD PICS!!!!!!!!!!!!!!!!!!!!! THUMBS DOWN!!!!!!!!!!!!!!!!